Search Documents

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By T Ye Koltunova an, L A. Otrozhdyonnova

This paper presents the results of studies on the development of an efficient non-cyanide technology for processing massive, finely disseminated, copper-zinc ores of the Urals deposits. Copper is mainly represented by chalcopyrite and zinc û by sphalerite. The main ore mineral is pyrite, with its content in ores varying from 50 to 80 per cent. At the present time, separation of copper concentrate at the Urals concentrating plants is achieved in a lime medium by non-cyanide technology using sodium sulfide and zinc sulfite as depressors of zinc and iron sulfides and butyl xanthate as the collector. Copper content in copper concentrates amounts to 15 - 17 per cent; considerable losses of zinc are associated with copper concentrate and final tailings. Various collectors were tested during the studies: xanthates and aerofloats with different lengths of hydrocarbon radicals, thionocarbamates, Aerofine 3418A of Cytec Industries, reagent S-703G of Mineral Reagents Int, and modifiers û sulfur dioxide, sodium sulfide and zinc sulfite, with a pH of the medium varying from 5 to 12. Optimum results of copper concentrate separation were achieved in a weakly acidic medium using S-703G as the collector and sulfur dioxide and zinc sulfite as modifiers. The copper content in the copper concentrate was increased by 4.8 per cent. Total copper recovery into the copper concentrate and zinc recovery into the zinc concentrate exceeded five per cent.

Jan 1, 2005

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By R. W. Raymond

This paper is simply a summary, prepared at the request of the Council of the Institute, of the report of Mr. Albert Ladd Colby, of South Bethlehem, Pa., presented at the New York meeting (October, 1896) of the Association of American SteelManufacturers, on " The Advisability of the Endorsement by the Association of the United States Standard Gauge, approved by Act of Congress, March 3, 1893, to the Exclusion of the Birmingham Gauge, the .Brown and Sharpe, and all Others:" a subject on which, at the Pittsburgh meeting (April, 1896) of the said Association, Mr. Colby had been appointed as a committee. The report favors the adoption, not of the United States standard gauge to the exclusion of others, but of a decimal system of gauging all materials in thousandths of an inch, thus doing away entirely with arbitrary gauge-numbers running in inverse order to the actual thickness. The American Institute of Mining Engineers originated this movement. The report of its committee on a standard wiregauge, presented in October, 1877,* recommended the abandonment of the system of fixed gauges for commercial use, and of the system of representing the diameters and sizes by numbers, and the adoption, in lieu thereof, of the system of expressing sizes in thousandths of an inch or fractions of a millimeter, and the use of the micrometer-gauge as a means of measuring sizes. In 1892 the American Society of Mechanical Engineers appointed a similar committee, and corresponding action was

Jan 1, 1898

By Horace M. Lawrence, Edmund S. Leaver

"The sulphidizing filming of minerals in oxide ores as a preliminary treatment to aid their recovery by flotation is known practice. In this work the use of barium polysulphide does not appear to have been considered. A study of the properties of barium lead to the following comparative investigation of the sulphides and polysulphides of the alkaline and alkaline-earth metals. It is thought that barium polysulphide may prove to be a more satisfactory sulphidizing reagent than others now in use under conditions that favor the cheaper barium reagent.For the investigation two fairly typical oxidized ores of copper and lead were selected. The copper ore came from the Big Indian Mine in southeastern Utah, and assayed 3.8% Cu; the copper was present in a sandstone gangue mainly as the carbonates, malachite and azurite, with less than 0.2% as sulphides, or silicate. The lead ore is from the Tintic Standard mine in the Tintic district, Utah. It is typical of the oxidized lead-silver ores of that district; the lead is present in an oxidised form in a siliceous gangue, much: Uncolored by ferric oxide. The sample assayed 5.15% Pb and 11.3 oz. Ag.In addition to the results obtained in this investigation, there are included some results secured by Mr. J. B. Lain, consulting metallurgist of Reno, Nevada, on a sample of ore from the Chino Copper Co. The ore assayed about 1.7% Cu, of which about 0.25% was nonsuiphide."

Aug 1, 1925

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By C. P. Mangelsdorf

Between June of 1975 and November of 1978 Stateham and Radcliffe of the Denver Research Center of the Bureau of Mines in cooperation with officials of the Bear Coal Company of Somerset. Colorado Conducted extensive studies of the roof conditions in the Bear Mine. The purpose of the investigation was to determine the relationship if any between the length of time the roof was left unbolted and the subsequent stability of the roof. Using the comprehensive information available from Stateham and Radcliffe (1), (2), (3), (4) the author has proposed a design for a roof truss installation which might have been used in lieu of some of the bolting in the areas where bad roof was encountered. Historically roof truss installations like bolting patterns have been applied rather than designed. The purpose of the present paper is to demonstrate how with the information available, one might proceed through a semi-rational design. In spite of the very extensive documentation by Stateham and Radcliffe, it was still necessary to make some working assumptions. It is, therefore, not intended that the process here illustrated be used without modification in any other mine nor is there any criticism implied or otherwise, of the way in which Bear Coal Company conducted its operations. The author has never visited the mine in question. This paper is meant to be an encouragement award a more rational use of roof trusses in situations where it is economically and structurally reasonable to do so.

Jan 1, 1984

By W. L. Dennen, V. H. Wilson

THIS paper is a description of the opera¬tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery of The Hudson Coal Co. during the first nine months of operation and follows a pre¬liminary description given at the Anthracite Institute in May, 1947, in a paper titled "Preparation of Anthracite Sift for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size operating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig 1 and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which handles the Breaker waste water. This underflow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped .to vibrating screens where the plus 316-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine

Jan 1, 1948

By Douglas F. Scott

Researchers from the U.S. Bureau of Mines conducted geologic investigations in an area of the Lucky Friday Mine, Mullan, ID, that included the 5300-107 demonstration stope using underhand longwall cut-and-fill mining. Structural analysis of the area suggested that argillite beds form planes of weakness between blocks of brittle quartzite, and energy may be released along these planes and at the junctures of fractures. Mapping argillite beds and fractures in the stope wall rock showed that the planes of these features diverged and that their attitudes corresponded from one wall to the other. Seismic analysis showed that the number and location of events varied as each cut was mined, with about 39 pct of the total number of events occurring above the cut being mined, about 54 pct below, and 7 pct at the same elevation.

Jan 1, 2010

By George W. Crawford, W. P. Aycock, E. W. Hough

Forty oilfield brines have been examined so far by a polarographic technique new in petroleum engineering called the "tensatnmetric method" by the team of biochemists who perfected its use in their field. Samples of brine were obtained from various oil fields in which the wells were known to be producing fluid from oil productive zones in well-known geologic formations. Most of the reservoirs from which the samples were obtained are believed to have an active water drive under the prevailing conditions of operation. The 40 samples represent brines produced front 16 different formations of various geologic ages. Graphs have been prepared of the data obtained in the testing of each sample, and the distinctive waife-like curves so obtained are characterized by reproducible profiles, called "response curves." Careful comparison of the response curves of salt water coming from different fields producing from the same geologic formation reveals that the curves are similar. The response curves of salt water coming from productive zones of different geologic formations are characteristically different. Preliminary work offers the further hope that response curves of an oilfield brine indigenous to a particular oil-bearing formation and hence representative of a particular geologic environment, such as deposit-ional and all subsequent morphological conditions, may be of value in reservoir engineering in the interpretation of surface and interfacial phenomena. For example, the wettability of the rock matrix and more specifically, the classification of productive oil-bearing strata as hydrophyllic or hydrophobic may be determinable. However, many more brines must be examined and the resulting response curves analyzed in comparison to known causal phenornena before this objective is achieved. INTRODUCTION One of the perennial moot questions in the literature of petroleum engineering is whether the reservoir rock is oil- or water-wet. Possibly an answer to this question could come from a careful examination of oilfield brines. None of the conventional methods of examining brines (chemical analysis, pH and electrical conductivity measurements, and the like) answer the question. Careful analysis of reservoir behavior observed in the exploitation of oil fields, particularly in the application of fluid injection, has been fruitful to the extent that a few reservoirs are believed to be properly classified. Physical chemistry suggests the behavior of reservoir brine and rock may be due to something in the brine in small amount. The ever increasing development and modification of theory in the general field of surface and interfacial chemistry has, and is, contributing to a better understanding of the problem, particularly as theory is verified by data. The work herein reported was begun in 1953 by Hough and Roebuck 1,2 who employed a new form of alternating current polarography, i.e., tensammetry, developed by Breyer, et a13,4 and who studied eight oilfield brines in adapting tensammetry to petroleum engineering needs. THEORY AND DEFINITIONS Tensammetry is a new technique of inquiry into surface phenomena. Specifically, a weak alternating current voltage is superimposed upon the direct current voltage applied to a dropping mercury electrode in contact with an electrolyte containing a small amount of a surfactant. The resultant alternating current can be measured and provides the experimental data for this new area of research. Under the influence of the direct current voltage, polar molecules arrange themselves in a double layer at the electrode. This double layer may be compared to a variable condenser, the capacitance of which is a function of the imposed direct current voltage. The direct current voltage determines the degree of adsorption of the surface active molecule on the electrode. Whenever the molecules are strongly adsorbed on the electrode, the capacitance of the double layer is low and the alternating current through the cell is low. Desorption occurs at some values of the direct current voltage, and at these voltages the capacitance of the double layer is high, resulting in an increase in the alternating current through the cell. The direct current

Jan 1, 1958

By Martin Williams

During the coming decade, many of the first generation of ‘super-pit’ gold and base metal mining operations in North and Latin America will reach the end of their economic lives. The closure of such pits in a manner which is environmentally sustainable presents a considerable challenge to the minerals industry. Pit closure often results in the partial or total inundation of formerly dewatered mining operations, and the resultant formation of lakes. The development of techniques for predicting, and controlling, the chemistry, groundwater discharge characteristics and long term hydrospheric impact of these lakes has become a critical aspect of pit closure planning. In this sense, the paper point out that Sleeper Mine was the first of a new generation of open pit gold mines developed in Nevada, USA. The closure of the Sleeper pit exemplifies the use of a range of pragmatic approaches to pit flooding, with applicability to mine closure at many other sites throughout the Américas.

Apr 22, 2003

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

By T. S. Golosinski

Most of the 154 t (170 st) truck fleets that were predominant in large surface mines in the 1970s and 1980s are approaching the end of their economic life. One replacement option considered by mine operators is a change to the 2 18 t (240 st) trucks. A comparison of load capacities between the 1.54 t (170 st) and the 2 18 t (240 st) trucks indicates a large productivity advantage in favor of the 218 t (240 st) trucks. This advantage, however, is often reduced by a number of site-specific factors. Therefore, a careful evaluation is required to define the actual benefit of changing to the large trucks. This article discusses some important factors that have an impact on truck size selection, based on several different studies. 218 t (240 st) trucks The 2 18 t (240 st) rear dump trucks were first introduced for surface mine service almost 10 years ago. However, it is only during the last few years that this equipment has gained acceptance in the surface mining industry. About 250 units were employed in surface mines worldwide at the beginning of 1992, and further purchase commitments are being made. Encouraged by the mining industry’s interest, all major off-highway mining truck manufacturers now offer 218 t (240 st) models (Table 1). At present, the existing 218 t (240 st) truck fleets are dominated by electric drive trucks. However, recent introduction of a 2 18 t (240 st) mechanical drive truck rounds out the development of this truck size.

Jan 1, 1992

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

By Harry L. McNeill

THE Selective Media Process was developed by the author in a laboratory provided by The Steårns-Roger Manufacturing Co. It is the outcome of an [ ] investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Cliffs Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7 ½ -hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼ -hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7 ½ -hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). When treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is fed to the washing plant the coarse

Jan 1, 1946

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996

By S. Dicarlo

"In late 1985, B-zone ore was first processed through the Eldor Mines mill at Rabbit Lake. Extensive modifications had been completed in order to mill this ore. In-plant process development was initiated to tune up the new circuits and concentrated on leaching, solvent extraction, impurity and uranium precipitation and tailing and effluent treatment. This process development effort and the results are described.INTRODUCTIONEldor Mines, a division of Eldorado Resources Limited, operates the Rabbit lake mine-mill complex at Collins Bay on the western shore of Wollaston Lake in northeastern Saskatchewan.The first orebody was discovered in 1968 by Gulf Minerals Canada Limited below a small body of water named Rabbit Lake. Ore from the Rabbit Lake (RL) deposit was first processed through the new mill in June, 1975, with depletion scheduled over the next ten years. Continued exploration in the area led to the discovery of four orebodies in the vicinity of Collins Bay: A-zone (1971), B-zone (1977), D-zone (1978) and Eagle Point (1980). Collins Bay is about ten kilometres from the mill facility.In 1982, Gulf Minerals was acquired by Eldorado Nuclear Ltd., who continued the development effort to bring the B-zone deposit into production. The RL pit was mined out in May, 1984 with stockpiled ore providing mill feed until startup on B-zone ore, which was scheduled for November, 1985."

Jan 1, 1988

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017