Search Documents

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

By Jon C. Volkwein

The U.S. Bureau of Mines has developed a method to measure methane and other gases during the auger mining of coal. An intrinsically safe commercial gas detector with a built-in data logger was mounted in the center of the hollow conveying auger. A sampling head through the wall of the auger conducted a gas sample to the detector. Results showed that gas levels can be monitored on a continuous basis during the auger mining of coal and the data retrieved upon completion of the hole.

Jan 1, 1994

By E. P. Youngman

By a decree of March 14, 1929,5 the President of the Faitian Repub- lic, considering it to be necessary, until the mining legislation of the Republic shall have been revised, to put into effect the mining law of Decem- Der 4, 1860 (relative to mines, diggings, and quarries), by the authority given in article 55 of the Constitution, declared the law of February 14, 1919, to be abrogated and the provisions of the earlier mining law (December 4, 1050) again to be valid. No concessions were granted under the law of 1919. All citations in this paper, unless otherwise designated, refer to the law of 1930.

Jun 1, 1932

By C. E. Silverblatt, D. A. Dahlstrom

Previous bench-scale studies demonstrated that a substantial moisture reduction can be obtained by the application of steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, U.S. Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous pilot-scale installation in which an Eimco extractor is used. The test results showed that the moisture content of this coal could be reduced to 5.5% at a steam loading of about 175 lb of steam per ton of dry cake. In terms of steam consumption, this loading is calculated to be 1-1/2 lb of steam per lb of water removed. In some tests, only 1 lb of steam per lb of water removed was required. These levels of steam consumption are significantly less than the actual heat requirements of conventional thermal dryers. The satisfactory moisture reductions were obtained at filtration rates of 125 to 186 lb of dry solids per sq ft per hour. However, the proper design of commercial filters should improve the potential rates that can be attained. These results indicate that steam filtration has considerable economic potential for drying 1/4 in. by 0 coals and also has additional advantages over the conventional thermal drying of coal. The results of the previous bench-scale studies and those published by Burton' demonstrated that a substantial moisture-content reduction can be effected by the application of slightly superheated steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, US Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous basis. In the continuous process, the dewatering operation on the filter is conducted in stages. In the first, the bulk of the water in the feed slurry is removed by conventional mechanical dewatering on a portion of the filter before the steam is applied. In the second stage, steam is applied to the cake. The steam condenses and releases its latent heat, thereby reducing the viscosity of the remaining cake water; this reduced viscosity then facilitates further drainage and produces a cake of lower moisture content. Because of the availability of feed coal on a continuous basis and since steam was readily available from a low-pressure boiler, the Applied Research Laboratory selected for the test site a coal-preparation plant that cleans Pittsburgh Seam coal. A slurry of table and flotation coal in percentages as they occur normally was used as feed stock. Typical analyses of this slurry are shown in Table I. DESCRIPTION OF FILTER AND EXPERIMENTAL PROCEDURES An Eimco Extractor was selected for the evaluation of steam filtration in a continuous process. This unit was chosen because of its availability and its design features that permit relatively simple hood construction, instrumentation, and operation. A photograph of the Extractor is shown in Fig. 1. In the filter a cloth medium is used that travels horizontally and continuously with a grooved, rubber drainage belt. The total effective filter area was 12.5 sq ft. As the feed slurry flows by gravity from the feed box onto the medium,

Jan 1, 1964

"With the plethora of cable bolts on the market, geotechnical engineers can be baffled by the differences in performance claims from the manufacturers but perhaps more importantly they are sometimes at a loss in making an optimal selection matching behaviour with a particular site condition. To this end a new testing methodology has been developed that can cater for the varying types of cable bolt behaviours. The methodology is based on the laboratory short encapsulation pull test (LSEPT) as recommended in the British Standard and overcomes several deficiencies such as cable rotation. Of most significance however, is its inability to measure the post-peak residual performance of high load transfer capacity cables and consequently, there is an inference that these cables may be susceptible to sudden anchorage failure with relatively little yield. This paper details the results of anchorage performance tests of a range of cable bolts and the differences in performance with rock strength and drill hole diameter.INTRODUCTIONA research project was undertaken to develop a new laboratory-scale test apparatus to study the axial performance of fully grouted cable bolts that are used in the Australian underground coal mining industry. Work by Thomas (2012) and others in recent years found there were a number of deficiencies in the testing methodologies making it difficult to determine and compare the performance of the dozen or more different types of cable bolts on the market. This has meant that geotechnical practioners have been hamstrung in optimizing the design of ground support systems in underground environments that are increasingly more arduous.A cable bolt is a flexible tendon consisting of a quantity of wound wires that are grouted in boreholes at defined distances between holes in order to provide ground reinforcement of excavations (Hutchinson & Diederichs, 1996). They were initially introduced into the underground hard rock mining industry in the 1960s (Thorne & Muller, 1964) and since the early 1970s have been brought to coal mining operations."

Jan 1, 2015

By Pina P, Pereira MJ

The increasing exhaustion of raw materials entails the exploitation of poorer orebodies where the target mineral occurs frequently in a very fine dissemination. Consequently it is necessary to grind more and more fine to achieve an adequate mineral liberation. In other words, it is of fundamental importance to know what size one should grind in order to avoid the following detrimental situations: 1. Excessive grinding - giving rise to the generation of ultra-fine slime particles which may be lost in the ulterior concentration process and simultaneously leading to higher energy consumption. 2. Incomplete grinding - giving rise to insufficient liberation and consequently leading to considerable losses of the valuable components in the tailings. Although this issue constitutes one of the most important steps in mineral processing, little research has been done compared to other processes, mainly due to the fastidious experimental work required. This paper describes a complete and integrated system of image analysis, where some algorithms to determine automatically the degree of li beration, for different levels of grinding, are proposed. These algorithms, mainly based on mathematical morphology theory were tested with images obtained from polished sections of different grain size fractions. Cases studies on a complex sulphide ore from an important copper and tin deposit located in the South of Portugal are discussed. Samples of the unbroken ore are also studied by image analysis to predict the degree of liberation obtained according to the fineness of grinding.

Jan 1, 1993

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By N. J. Sather

The history of the Bunker Hill mine dates back to August 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d'Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co.

Jan 6, 1961

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard' showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.' Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y' eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y' pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By J. Alton Burks

When acoustical materials are used in a mining environment for noise control purposes, they are subject to environmental deterioration from hydraulic fluid, moisture, and dust. These and other factors can cause physical degradation of the material, which can lessen its ability to absorb sound. In this study, the Bureau of Mines measured the sound absorption properties of 16 different acoustical materials after 4 sample treatments: (1) being kept clean and dry (as received from the supplier), as a control or reference standard, (2) immersion in water and draining, (3) immersion in lOO-pct-petroleum-type hydraulic fluid and draining, and (4) exposure in a coal mine. The last three treatments were used to approximate the type of physical degradation that can be experienced in actual use. The impedance tube or standing wave method was used to measure the normal absorption coefficient. It was found that the absorption coefficient of most materials was adversely affected by the retention of either oil or water, with oil having the greater effect. The only class of materials that was affected by neither oil nor water was neoprene foam.

Jan 1, 1990

By Shian Jia

Ultrasonic Stirring Technology (UST) is used in this study to manufacture Al-based nano-composites. Ultrasonic cavitation plays an important role in refining the microstructure, dispersing the nanoparticles and breaking up clusters of nanoparticles. In this paper, 6061/A356 alloys and Al2O3/SiC nanoparticles are used as the matrix alloys and the reinforcements, respectively. The nanoparticles were inserted into the molten alloy and dispersed by ultrasonic cavitation and acoustic streaming. A previously developed multiphase Computational Fluid Dynamics (CFD) model was used to study the cavitation and the nanodispersion phenomena during ultrasonic processing of these alloys. A comparison between the mechanical properties of the as-cast 6061 and 356 alloys and nano-composites has been performed.

Aug 16, 2017

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By N. Akbulut, A. Anani

From the initial planning phases to the closing of a mine, mining is an industry where high attention, care, and sensitivity are needed in every step of the mine life. Since mining projects have a long-life span, exceeding a decade sometimes, managing a whole mine project is challenging, especially when challenges faced due to generational differences are considered, such as tracking and logging data, or the usage of different engineering solutions change over time. Along with the overall hardship caused by the time put into a mining project, the present-time operations are very costly where each minute counts. In present-time operations, every decision made, and every minute used during planning and operations has an impact on the efficiency, safety, and economics of the project. Having extremely harsh conditions in both the excavation and mineral processing operations not only slows down the processes but creates very dangerous environments that need to be handled with precise safety measurements. To support the already established processes, we could implement new technologies and use them to our advantage. Virtual reality (VR) is one of these technologies that we could implement in the mining industry. VR is a technology that emerged in the 1960s creating virtual environments and platforms. The user experiences these virtual environments from head- mounted headsets to rooms with 360 screens, all with different levels of immersion. These higher levels of immersion, create a higher level of presencemaking the users more engaged in the activity they are trying to accomplish. These two factors of immersion and presence are what make VR unique and beneficial. VR has some applications and case studies in the industry along with some research being conducted in universities. Unfortunately, there has not been a comprehensive literature review or analysis regarding only VR and its implementations for the mining industry in the last 5 years. This paper aims to describe what VR is and its relation to the mining industry, in the most recent years. The paper first gives a brief background on what VR is and its key concepts. Secondly, it will give information on how the initial stages of the literature review were conducted and the findings along with discussions. The paper will finish with the conclusion drawn from the discussion and potential future work.

Feb 1, 2023

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

By G. M. Potter

During the investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from four properties in Siskiyou and Mendocino Counties northern California. As the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were made between 1941 and 1945 to determine the amenability of the ores to concentration. The Johnson and Reynolds properties are near Fort Jones Siskiyou County. The ore occurs in a number of small lenses in that area. Samples were taken for testing for amenability to treatment in a small custom-gravity plant, tentatively planned. by the Waiter Johnson interests of San Francisco. A 2-ton representative sample was obtained from numerous exposed portions of an outcrop on the property of the Mayland Mining Co. The Mayland mine is about 8 miles from Sawyers Bar in Siskiyou County. The ore body consists of stringers and irregular masses of oxide, and. silicate ore scattered through quartz, which these minerals have replaced.

Jan 1, 1952

By Constance F. Acton

This paper presents an overview of -- the carbon-in-pulp process for gold and silver recovery as seen in the early 1980's. Traced back to its origins in the mid-nineteenth century the process development through the present state-of-the art is described. The process technology and equipment design are described in detail for the carbon-in-pulp process. A typical process flowsheet is given with a description of appropriate design criteria. Technical advantages and disadvantages as compared to the traditional countercurrent decantation process are discussed including some illustrative comparisons of capital and operating costs. A summary of currently operating carbon-in- pulp plants throughout the world is given with an insight into future developments in this industry.

Jan 1, 1982

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993