Search Documents

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Wenxuan Xu, Shusen Cheng, Tian Chen

Pulverized coal injection (PCI) can generate heat and reducing gas in the raceway and replace some expensive metallurgical coke in the blast furnace ironmaking process. In this paper, a three dimensional mathematical model of the raceway including the coke bed has been developed to simulate the complicated phenomena of pulverized coal injection. The effects of oxygen enrichment, particle diameter in the raceway are investigated in this study. The establishment of the 3D model is expected to analyze the raceway working state accurately and optimising the PCI operation of blast furnaces.

Mar 1, 2017

By A. S. MacNeil

In the operation of any colliery, a factor of prime importance is power, of which there are three sources available--man, horse, and mechanical. It is obvious that man-power is by far the most expensive, .and that animal-power, also, is more costly than mechanical. In recognition of this fact, mine owners must, for economical ?reasons, reduce the use of man-and horse-power to the minimum by the increased use of machinery. In other words, they must aim at as complete mechanization as conditions will permit, taking advantage of existing physical factors that are favourable and making the necessary adjustments and modifications to meet the less favourable conditions. Intensive coal-mining, or the concentrated production of coal, has two distinct objectives: First, the maximum production from a limited area, in a given time, thereby reducing the pit-room to be maintained; and second, reduction in cost. To this end the coal should be mined, loaded and delivered to the surface by mechanical means wherever possible. To do this, however, requires the solution of many problems arising out of the varying conditions that obtain underground. The system of longwall mining lends itself to a more efficient scheme of mechanization than does pillar-and-room, as, in the former, the first step has already been taken by the removal of all the coal in one operation, and the opening-out of one face, the equivalent in mining area of fifteen or more rooms. Much has been clone of late towards mechanization in the longwall mines of the Sydney coal-field, and with gratifying results, but not without great difficulties and frequent disappointments. In 1923, an attempt was made with shaker conveyors. The introduction of conveying was a step to bridge the gap between the face, where the coal is produced, and the main transportation arteries leading to the slope or shaft. The receiving of the coal at the faces and its delivery to main loading points on main haulage-ways was the part allotted to the conveyors.

Jan 1, 1932

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By J. A. Cole

The mill project at Lone Tree was commissioned in October, 1993, followed by the commissioning of the autoclave pressure oxidation circuit in February, 1994. Discussion of the first year of milling operations at Lone Tree is presented. The mill is currently operating above the design rate of 2,267 mt/d (2,500 st/d). Both phases of the start-up were essentially trouble free. The few problems that were encountered and the respective solutions are addressed.

Jan 1, 1995

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

Jan 1, 1934

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By J. A. Eisele

The Federal Bureau of Mines is engaged in a continuing program on the recovery of alumina from domestic source materials. Of the six processes being studied, current efforts focus on HCl leach of clays. A key step in the HCI process is the removal of iron from the aluminum chloride leach liquor. This was accomplished .by solvent extracting the iron with a tertiary amine in kerosine to which decanol was added as a phase modifier. In a mixer-settler operation, iron in the raffinate was reduced to <10 ppm in two extraction stages from a feed containing 1.4 gil Fe. Iron was stripped from the organic phase in three stages with dilute HCl.

Jan 1, 1976

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By Thomas Boundy, PATRICK TAYLOR

Indium recovery from liquid crystal display (LCD) waste has been the subject of over 50 peer reviewed publications over the last decade; however, the first commercial recycling facilities are just beginning to be built. The low value of indium in the LCD screen material has posed a major challenge to would-be recyclers. Uncommon material combinations and geometries have further challenged development. A review of published literature regarding extraction of indium from LCDs will be presented and themes of advantageous processes will be highlighted. Barriers to rapid expansion of any recycling technology in the form of manufacturin gpractices, environmental regulations, and geographic constraints will be discussed.

Mar 1, 2018

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983