Search Documents

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By P. K. STRONG

AS an evidence of the fact that mines safety is not being neglected even in the remote district of the Philippines, a short account is appended of the organization and activities of the Mambulao-Paracale District First Aid and Mine, Rescue Association, whose headquarters are at Jose Panganiban Cam, Norte P. I. The second annual miner?s safety celebration which is sponsored by the Association was held in Paracale on Sept. 2, 1940. The event is the big occasion of the year when the thousands of employees of the mines in the district meet to compete for prizes and has become a great social function as well.=

Jan 1, 1941

By Sérgio Roberto Lopes Moreira, Leonardo José Silva de Oliveira, Rodrigo Seara Martins, Rodrigo Madrona Dias, Fabiano Abrahão Moreira

O nível de inclusões presentes no aço líquido interfere diretamente na qualidade das placas produzidas por lingotamento contínuo e são determinantes na formação de defeitos superficiais em produtos laminados a frio. A reoxidação do aço, bem como a passagem de escória do distribuidor para o molde, a interação do aço com o pó de cobertura do distribuidor e com o pó fluxante, têm forte influência na limpidez das placas originadas no processo de solidificação no molde. No presente trabalho, avaliaram-se as inclusões formadas durante o início do processo de lingotamento contínuo para aços de ultra baixo teor de carbono, sob três diferentes condições de adição do pó de cobertura do distribuidor, além da própria condição padrão. O objetivo do estudo é reduzir a quantidade das inclusões e consequentemente, os defeitos superficiais em placas iniciais, por meio da relação com o teor de oxigênio no veio da máquina de lingotamento contínuo. Tal investigação visou fornecer informações para alterações nas condições do processo para melhoria da qualidade do produto final.

Oct 1, 2019

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By W. R. Hardwick

This information circular describes mining methods and practices at New Cornelia Branch, Phelps Dodge Corp., Ajo, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The New Cornelia mine (fig. 1) is at Ajo, a town in southwestern Arizona (fig. 2) on Arizona State Highway 85 in the western part of Pima County. The [oncentrator] and smelter are near the mine (fig. 3). Copper ore is mined, crushed, ground, and concentrated, and the concentrates are smelted. Copper is cast in anode form and sent to the Phelps Dodge Corp. refinery in El Paso, Tex.

Jan 1, 1960

By Salomón David Albis Pacheco

El presente texto señala una herramienta de gestión actual que mejore las operaciones logísticas de la empresa, perfeccione el sistema de información con los proveedores y brinde una mejor respuesta a los clientes mejorando el nivel de servicio. En ese sentido, Supply Chain Management (gestión de la cadena de suministro) es una herramienta de gestión que ofrece minimizar los costos y logra un mejor servicio al cliente - en tanto al aplicarla a una contratista minera de perforación diamantina, optimiza los contratos, compras, almacenes, transporte de materiales, tecnología de información y maneja la responsabilidad social y ambiental.

Mar 1, 2014

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By W. C. Lilliendahl, G. Meister

Uranium metal with a purity of about 99.9 pct was produced on a large scale by fused salt electrolysis with a material efficiency of about 90 pct. The material efficiency depends mainly on bath composition, electrolysis temperature, electrode smothering, and elutriation during washing of the powder. RESEARCH and development work on fused salt electrolysis carried on by the Westinghouse Lamp Div. Bloomfield, N. J., was done under the Manhattan District Corps of Engineers and later under the Atomic Energy Commission for the commercialization of uranium production for the first atomic pile at the University of Chicago in 1942. From the conception of the atomic bomb project it was recognized that metals with impurity levels having little metallurgical significance would be required. Permissible impurity levels were based on neutron absorption. Of particular significance was boron, which could not be present in amounts exceeding 1 ppm. The electrolytic method as developed in 1930 by Driggs and Lilliendahl,1,2 and later improved, yielded uranium of very low boron and other deleterious impurity content. No other method was capable at that time of producing uranium metal of the required purity.' The low boron content of uranium produced by the electrolytic process resulted from the availability of the reactants which were low in boron content, and from the inherent elimination of boron in the fused salt bath. Since the heart of any electrolytic process is the electrolysis cell, this paper will deal with the development of the original bath composition for the efficient production of uranium from a batch process to one of continuous operation. Emphasis also will be placed on other factors which will affect the material efficiency of the process. With the laboratory cell the material efficiency of uranium powder recovery in the early electrolysis was relatively low, about 35 pct based on the ratio of uranium recovered to uranium added. This early process also had other defects. The electro- lytic bath could not be used continuously. After three runs from a freshly charged crucible, the deposit showed a tendency to slip off the electrode as it was raised from the bath. This condition necessitated pouring the charge every fourth run and preparing a new bath. It was assumed at that time that this condition was caused by the increasing fluoride concentration with each addition of uranium salt, which adected the mobility of the uranium ions. Experimental The electrolysis cells differed in size only. They were of the floating cathode type. The laboratory cells were 21/2 in. ID and 6 in. deep and operated at 30 amp and 5 volts. Production was about 150 g metal powder per 8 hr. The plant cells (5 units) were 9 in. ID x 21 in. deep and operated at 1800 amp at 12 volts. The total production unit was designed to produce 250 lb of uranium powder per 8 hr day. Because of the tendency of uranium fines toward spontaneous combustion, material efficiencies were based only on the recovery of useful coarser metal which could be safely handled. The reported efficiencies are of particular significance only as related to the same group of experimental procedures. At the start of the project no changes were contemplated until previous data could be definitely confirmed. Therefore, the first experiments were with the 50 pct CaCl2-50 pct NaCl mixture. The material efficiency of uranium deposition as a function of the number of electrolyses is shown in Table I. In Table I, the decrease in efficiency at 800°C with number of runs is apparent and confirmed the earlier data. Operating at 900°C enabled the number of runs to be doubled, but before pouring the charge the efficiency of recovery became poor. This test indicated that the improved efficiency might have been caused by an increase in the fluidity of the bath.

Jan 1, 1958

By M Mohammad Khani

An economic block cave is dependent to the characteristics of the rock mass at stages of caving. These are cave initiation, propagation and ore flow. In this research, the rock engineering system (RES), first established by Hudson (1992) to solve complex rock engineering problems, is introduced and verified against the well-established caving parameters established by Laubscher. There are two types of factors influencing caving and these are natural (cannot be controlled) and induced (operator controlled). A RES based interaction matrix is developed by determining the rating parameters required to reproduce the caving database using Laubscher’s caving parameters. This provides the relative importance of the parameters in the interaction matrix. After discussing the rock mass caving process and identifying all the effective parameters, an interaction matrix is introduced to study the cave initiation of rock masses. The expert-semi-quantitative (ESQ) coding method is utilised to assign the numerical value to each parameter’s interaction. Thereafter, the interaction intensity and dominance of each factor in the system is determined to classify these factors. Finally, all the parameters affecting caving operation and their weights on the RES system are identified. This new application of RES in block caving is very efficient and useful for any stage of caving studies and helps experts to make decisions more accurately.CITATION:Mohammad Khani, M, 2016. The application of rock engineering systems to block caving to identify the effective parameters, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 853–860 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

By Aquiles Vivar Montañez

"La construcción de losas de relleno cementado en la aplicación del método de corte y relleno descendente, es una etapa importante en el ciclo de minado - en tanto representa uno de los mayores costos de extracción por tonelada de mineral. En este contexto, es necesario establecer metodologías adecuadas para el diseño de losas basadas en técnicas empíricas y analíticas, así como para el de recuperación de pilares. Por ello, el presente texto señala la optimización de la resistencia del relleno cementado a través de la reducción del ancho de minado en los sectores de mayor potencia y la reducción del módulo de rigidez de la losa para que guarde equivalencia con la rigidez de las rocas encajonantes, que son de baja calidad geotécnica. "

Sep 1, 2015

By HILLARY W.

THAT colleges and technical schools constitute a vital factor in our industrial system is being realized more and more of late years. Consequently it is desirable that there should be a constant interchange of ideas between the 'school and the industries and that there should be a more intimate contact between the student and his future employer. Business and industry demand certain proficiencies and qualifications of the student and he, in turn, sees certain rewards and advantages in the industry. . In a meeting of this kind, whose primary purpose is to promote a greater intimacy between the students and those men who are active in the mining profession, it is quite fitting that each state his demnds upon the other in order to establish a common understanding. It is probable that a student, not being conversant with actual conditions in the industry, may be unfair in what he asks of his employer. Therefore criticism, constructive or other- wise, is not only accepted, but is invited.

Jan 1, 1930

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002

By Orris C. Herfindahl

Every few years we are treated to a battle over trade policy when the Reciprocal Trade Agreements Act comes up for consideration. In 1962 it is especially appropriate to consider the problem of mineral import -policy and the closely related problem of general import policy, for this year's struggle is different from those of the past in two ways. First, proposals have been made which are a substantial departure from past trade agreements legislation, and second, the formation and growth of the Europe Economic is Community may have an important bearing on the kind of legislation that is adopted. But this anticipates what is to come later. My task is to examine the problem of mineral import policy, although we shall find soon enough that general trade policy must be considered in order to get an indication of what is in store for minerals.

Jan 1, 1962

By D. Allan Coutts

Demonstration projects using hydrogen as a fuel are becoming very common. Often these projects rely on project-specific risk evaluations to support project safety decisions. This is necessary because regulations, codes, and standards (hereafter referred to as standards) are just being developed. This paper will review some of the approaches being used in these evolving standards, and techniques which demonstration projects can implement to bridge the gap between current requirements and stakeholder desires. Many of the evolving standards for hydrogen-fuel use performance-based language, which establishes minimum performance and safety objectives, as compared with prescriptive-based language that prescribes specific design solutions. This is being done for several reasons including: (1) concern that establishing specific design solutions too early will stifle invention, (2) sparse performance data necessary to support selection of design approaches, and (3) a risk-adverse public which is unwilling to accept losses that were incurred in developing previous prescriptive design standards. The evolving standards often contain words such as: ?The manufacturer shall implement the measures and provide the information necessary to minimize the risk of endangering a person?s safety or health.? This typically implies that the manufacturer or project manager must produce and document an acceptable level of risk. If accomplished using comprehensive and systematic process the demonstration project risk assessment can ease the transition to widespread commercialization. An approach to adequately evaluate and document the safety risk will be presented.

May 1, 2007

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023