Search Documents

The probability of detachment of quartz particles from air bubbles during bubble oscillations was investigated by means of a vibration method. Theoretical calculations of the detachment force based on the work of Nutt and Schulze for a single spherical particle show a correlation with the experimental results described. However, the forces that were determined experimentally were considerably lower than the theoretically derived values. Some of the factors which were expected to affect the probability of detachment, such as particle size, bubble size, collector concentration and vibrational acceleration, were also investigated

Dec 1, 1991

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

Jan 1, 1879

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Clyde E. Williams, JAMES L. GREGG

THIS review of the past year's progress in iron and steel metallurgy presents examples of only a few of the interesting or important accomplishments made in the United States. In the field of iron ore concentration increased attention was given to the study of the more difficultly separated wash ores and some progress was made in tabling. One difficulty with the table, in concentrating iron ore where the percentage of concentrate in the feed is large, has been the removal of fine silica from the thick layer .of concentrates in the cleaning zone. One company has -Made an important contribution toward the solution of this problem by an extension of the well-known plateau principle. By a special riffling of the plateau section of the table, the concentrates are crowded together. This action forces the fine silica to the top of the bed in the cleaning zone, whence the cross-flowing currents of water -can wash it into the middling product. Some work has been done on the application of froth flotation to the concentration of iron ores. Laboratory experiments were made at the Colorado School of Mines in which hematite was, successfully floated. Using oleic acid as a frothing and collecting agent and sodium carbonate as the conditioning agent, a high recovery of rich ,concentrate was obtained. A laboratory flotation unit is in use at Taconite, on the Mesabi range, and a commer-

Jan 1, 1932

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By Fei Chen, Xun Xu, Dezhong Kong, Yu Xiong

We address the problem of rib spalling caused by mining-induced roof movement. This problem affects production and safety of the working face. We address this problem by using the 3DEC numerical software to simulate the distribution and evolution regularity of displacement, stress, and the extent of plastic zone in the overlying strata and coal face during the advancing excavation of the 10,905 working face of the mine. Results showed that the first weighting interval of the 10,905 working face is 50 m, and the periodic weighting interval is 20 m. The fractures of overlying strata develop during the first weighting; the vertical stress and vertical displacement of the main roof increase by 45% and 10%, respectively; the vertical stress of the coal face increases by 11%; and the plastic zone in front of the working face increases rapidly. The displacement and stress of the main roof and coal face change periodically during the period of periodic weighting. The variation range during the periodic weighting is less than 30%, but the overall degree is larger than that before the first weighting. Finally, the integrity and rationality of numerical simulation are supplemented and verified by similarity simulation. On this basis, the proposed roof and coal face stability control scheme reduces the maximum horizontal displacement of the coal face from 16 to 4 cm, that is, a decrease of 75%. This study provides theoretical guidance for roof support and coal face stability control of working faces under similar conditions.

Dec 26, 2022

By Albert J. Forney

Extensive studies have been made of the various effluents found in the Synthane coal-to-gas process. Analyses have been made of the waters, gases, and trace elements present in some of the streams. Results of analyses show the water effluents are the area where extensive research is needed.

Jan 1, 1974

By Richard G. Stearns

Extensive thick lignite apparently lies within 250 feet of the land surface in Dyer, Lake, Lauderdale, Obion and Tipton counties. Information on geology, land use, soils, groundwater and instability is compiled, along with a bibliography. A test and monitoring site was investigated at Fort Pillow Prison in Lauderdale County. Analyses were made of lignite, overburden, associated water and leachate. Lignite has high BTU (about 7800) and low sulfur (1.1% avg.). A year or more of data are presented on rainfall, water levels, and chemistry of surface water, groundwater, leachate and water from test pits. Main potential environmental problems are quality of surface water, and possibly shallow groundwater. The main aquifer of the region will likely be un-affected by mining. Low transmissibility of shallow aquifers will minimize lowering water levels of wells. Soil reclamation and conservation should be readily accomplished, Dangerous earthquakes have a low probability and mines are not significantly more hazardous than steep bluffs.

Jan 1, 1981

By Georgene Renner, William R. Yernberg, Steve Kral

Advanced Terra Testing (ATT)is a full-service geotechnical testing laboratory. It specializes in rock and soil mechanics and geosynthetic materials testing. ATT provides services to the global mining industry. The company has performed more than 1,000 projects for more than 300 commercial and government clients. Services include coal pillar design testing, leach pad material and performance testing, tailings pile consolidation testing and closure and remediation services. Rock and soil mechanics tests include unconfined and triaxial strength, shear and tensile strength, permeability, index testing, consolidation, liquifaction potential, elastic moduli determinations, heap height versus percolation rate, long-term batch testing and dynamic loading tests.

Jan 1, 2003

By Valois R. Shea-Albin

Ground control problems are an important factor affecting safety, production, and efficiency in underground coal mines. A major portion of ground control problems encountered in underground coal mines can be attributed to geologic features in the strata surrounding the extracted coal seam. The U.S. Bureau of Mines has compiled information from numerous sources on the geological features that contribute to ground control problems in underground coal mines. The compilation includes (1) sedimentary features such as paleochannels, crevasse splays, clastic dikes, mold-and-cast structures, concretions, and lithologic factors, and (2) structural features such as folds, fractures, joints, cleat, and faults. The compiled information will aid in identifying the features, predicting their occurrence in advance of mining, and controlling or minimizing roof failure when these features are encountered in an underground coal mine.

Jan 1, 1993

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

The interaction of man with the environment has a double character. From one side, mankind can not exist without co- nsuming the natural resources and, from the other side, we actively alter and exert influence upon nature. Analysis reveals that the ecological problem is, to a great extent, a geological one. The paper deals with the application of grouting techniques to construct impermeable barriers for the protection of ground water and soils from depletion and industrial wastes pollution. A number of case histories in the field of mine construction is given to illustrate the solution of geotechnical problems in concert with environ- mental protection measures.

Jan 1, 1988

By George J. Young

DR . JOHN A . CHURCH, in his treatise on the Comstock Locle 1 gave a full and clear account of the conditions of the mine during the period of greatest activity. The difficulties in the way of deep mining at that time were excessive water and high temperature. The drainage of the mines taxed the financial resources of the mining companies, and the high temperatures restricted the capacity of the miners for underground labor. In spite of these difficulties exploratory work was continued until the financial burden of removing the water became too great. The companies then restricted the work to the upper levels. The years 1883 to 1886 marked the period of cessation of deep mining. For 12 years thereafter mining was confined to the levels above the Sutro tunnel; and, while the question of drainage was more or less agitated, nothing of importance was done until the formation of the Comstock Pumping Association in 1898. Since that time successive levels have been drained until, at present, on the north-end mines, a depth of 700 ft. below the Sutro-tunnel level has been reached. Mining is now carried on in the Ophir mine from the 1,700- to the 2,200-ft. levels, and a winze is being sunk to make connection with the 2,300-ft. level (the 2,450 ft. of the C. & C. shaft). In 1903-the Ward Shaft Association was formed to undertake the draining of the Central and Gold Hill group of mines, and at the present time a depth of 2,500 ft. has been reached in the Ward shaft. The situation at the Ward looks promis¬ing, and the 3,000-ft. level may be reached in the near future. It is proposed to establish a large pumping-station on this level, and then begin the opening of known ore-bodies and the prospecting for new ones. The main factors which have contributed to the successful solution of the drainage problem are the Sutro tunnel, the use of the hydraulic elevator as a sinking-pump, the concentration of pumping-units, and cheap electrical power. The question of high temperature and its control still remains as a minor but important problem. The temperatures encountered in the new workings are as great as those in the earlier periods. The Comstock was considered the hottest group of mines in the world, and I am not aware of similar conditions in any other mining-district. A water-temperature as high as 160° F. has been reported from the Ward shaft, and temperatures below the Sutro tunnel are very high in many instances.

Nov 1, 1909

By R. Steven Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate specialty metals such as cobalt, nickel, bismuth, rhenium, molybdenum, indium and germanium from various primary and secondary feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams.