Search Documents

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

The tungsten carbide insert bit has probably advanced blasthole drilling more than any other single improvement. Tungsten carbide inserts have longer life, maintain sharper edges, and penetrate faster than hardened steel edge bits. Before the tungsten carbide hit appeared, all-steel bits were used. Even with the new bits, blasthole drilling costs vary with the type of equipment used and its condition; the hole's length and diameter; the rock's texture, hardness, and nature; the operator efficiency. To help reduce drilling costs, the operator should be familiar with the use and care of drill bits. This article provides information about tungsten carbide rock bits used for percussion drilling. Consideration of tungsten carbide rock bits includes looking at bit materials [ ] as well as bit operation and maintenance. Two basic tungsten carbide rock hits are the button bit and the four-wing carbide insert bit. Three common hit-to-drill-steel connections are the bottom drive, tapered drive, and shoulder drive. Bottom drive bits arc typically used for singlepass or longhole drilling, with all percussion drills from handheld sinkers to heavy track drills. Tapered socket bits are available with shallow or deep carhide inserts, for the lowest cost depending on the rock type being drilled. Shoulder drive bits are available in all-steel or carbide insert design.

Jan 12, 1981

Nearly eighteen months ago Newmont Waihi Operations joined with the local district council and members of the Waihi community in the initiation and running of a community liaison forum.   This forum û the Waihi Community Consultative Committee (WCCC) û was set up with the objective of improving communication, providing a forum for discussion and ultimately working through a range of issues relating to the future of the town and district after the projected closure of Martha Mine in late-2006.   After 18 months of meetings where all represented groups have presented their views, the challenge now is to work together to investigate likely options, seek sources of funding, produce business proposals and plan for the future of Waihi in what we call the Golden Legacy Project.   This paper backgrounds the companyÆs experiences to date, the issues the group has addressed and its proposals for the future. Methods employed to set up an effective community liaison forum are considered, drawing on specific examples from the WCCC. The actions and structures required to ensure effective and ongoing community æbuy inÆ at all levels are also discussed.   This paper develops themes addressed in Taking it to the Streets presented in 2003.

Jan 1, 2004

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By William N. Fitch, Valois R. Shea-Albin

In 1976, the Resources Conservation and Recovery Act (RCRA) aroused concern in the mining community about the regulation of mine waste streams under RCRA. In response, the Bureau of Mines initiated research in the late 1970's that addressed mine and minerals processing waste. Research included investigating improved environmental technology for metal, coal, non-metal, and emerging industries such as oil shale, tar sands, peat, and lignite. Environmental issues escalated in the 1980's. Proposed regulations addressing control technology for mining and mineral processing wastes prompted the Bureau of Mines to become involved in 1985 in an advisory capacity to the regulatory agency, the Environmental Protection Agency. In Fiscal Year 1988, the Bureau of Mines initiated a research program designed to provide the minerals industries with cost-effective solutions for ameliorating environmental effects of mining. Bureau research has led to advances in the areas of acid mine drainage control and mitigation, subsidence prediction and control, and control and treatment of solid wastes resulting from mining and mineral beneficiation. The Bureau also conducts research seeking new methods to remediate abandoned mine lands. A discussion of the mine waste issues is presented, followed by a summary of past and present research conducted by the Bureau of Mines.

Jan 1, 1991

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By B. J. Kochanowsky

To improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi,' Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,' editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature."

Sep 1, 1955

By Robert Snow, Yingxue Yu, Howard Hanson, Patrick Zhang

One of the major current efforts by the Florida phosphate industry to reduce deep aquifer water consumption is to use 100% recycle water for flotation. This measure alone could save billions of gallons of deep well water annually. However, this also results in higher suspended solids (slimes) in flotation water, causing poor process performance particularly for amine flotation. Polymers could play a major role in allowing the industry to use high-turbidity recycle water for amine flotation without compromising its impact on the Florida economy. The enhancement of rougher flotation by polymers may also have potential. Most importantly, dramatic efficiency improvement may be realized by floating silica first. Adding polymer to flotation feed and/or water is perhaps the most economically viable way of reversing the Crago "double float" process, in order to reduce operating costs and increase phosphate recovery. This paper presents both laboratory and pilot flotation data showing the effect of different polymers on collector dosage and flotation recovery. There appeared to be an optimal range of polymer concentration beyond which the benefits do not offset the drop in phosphate recovery. The effect of poly mer is slime-level dependent. Pilot testing data show that the "Reverse Crago" process (floating silica first followed by phosphate flotation) can outperform the Crago process.

Jan 1, 1999

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By B Mil, D P. Adhikary, M S. Craig, P Rutzou

As shallow coal reserves with easier mining conditions are exhausted, future deep coal mining with difficult mining conditions may face significant economic, technical and environmental challenges. Moreover, due to increased coal production capacity with the new generation longwall systems, predicting adverse mining conditions has become more important than ever before. The potential impact of these difficult conditions is an increase in mining risks and costs. Reliable prediction of rock mass deformation, mine stability and mine water inflow is not only essential for improving mine safety and reduction of coal production costs, but it is also important for the assessment and management of the environmental impact of mining. This paper briefly describes an integrated approach to mine groundwater simulation and prediction. Central to this integrated approach is a three-dimensional computer code called COSFLOW, developed by CSIRO of Australia in collaboration with NEDO and JCOAL of Japan to address the pressing issues of mine water management. COSFLOW incorporates unique features that make it ideal for the simulation of coal mining and examining the interaction between rock fracture, aquifer interference and water flow. This paper also presents an example of an application of the integrated approach and COSFLOW in water inflow prediction at Springvale Mine in New South Wales.

Jan 1, 2006

By Sparrow GJ, Woodcock JT

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t An, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5-40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects.Direct cyanidation for 48 h extracted only 26% of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77%. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88%, giving a tailing assaying 1.5 g/t Au.

Jan 1, 1990

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By F. Simon, A. Roth, M. F. Zaeh

Applying Friction Stir Welding in an industrial environment requires knowledge about the robustness of the welding process against imperfections in the joint line resulting from production deviations of the parts to be joined or from improper clamping devices. In this work the influence of gaps on the weld quality of friction stir welded butt joints of the aluminum alloy EN AW-5083-H111 is investigated in detail using the method Design of Experiments. As independent input variables, the rotation speed, the feed rate, the tilt angle, the lateral tool offset and the gap width were chosen. Tensile strength was selected as a measure for the joint quality. Moreover, the fundamental response variables of the FSW process, such as weld temperature, axial force and spindle torque, were recorded and integrated in the empirical process model derived by regression analysis. It was found that each response variable decreases with increasing gap width, whereas the largest impact was identified for the axial force and the temperature at the weld surface. In order to improve the joint strength for a given gap width, increasing the rotation speed and the tilt angle or lowering the feed rate, respectively, proved to be a suitable approach. However, interactions between the tilt angle and the rotation speed have to be considered.

Jan 1, 2014

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998