Search Documents

By N. Mohan, A. K. Biswas, V. Y. Sampat Kumar

At low sodium-oleate concentration, calcite flotation is substantially improved by the use of CO2 instead of air. Electrophoretic mobility measurements indicate that carbonation results in the accumulation o f positive charge on the calcite particles. This heightens adsorption of oleate anion, an effect confirmed by tracer-technique measurements. Fundamental insight is obtained as to how CO2 serves better as an activator than some mineral and organic acids, how oxalic acid acts as a depressor, and why the influence of Ca++ ions, liberated during carbonation, on flotation behavior of calcite is insignificant and sometimes adverse.

Jan 1, 1972

By F. Kennedy

Consolidation Coal Co. (Consol) supports an active research and development effort to improve the safe, productive mining of coal and to use coal in an environmentally acceptable manner: Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1 % of Consol coal sales, which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with using the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1990

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

By M. Spangler

FirstMiss Gold installed a supervisory control system that is based on Pavilion Technology's Process Insights neural-network software and Oil System's PI data historian. The first successful control loop involved controlling the limestone feed rate to the neutralization circuit. The resulting improvements in the control of the circuit resulted in savings of $31,000 per month. Although it was the primary goal of the system, supervisory control of the preconditioning circuit was not achieved. However, information gained during the modeling suggested process modifications that resulted in cost savings of $54,000 per month in the preconditioning circuit.

Jan 1, 1997

By Walter E. Heinrichs

Before covering the separate methods used in mining geophysics, it may be well to mention some current basic geophysical prospecting concepts. As in most fields, a better understanding and means of studying these fundamentals usually provides the more common improvements, rather than new principles being discovered. The relative detail and complexity of most mining geology often results in the use of geophysics in problems it cannot solve. On the other hand, suitable applications are often ignored or left unrecognized. To minimize this, it is important to consider geophysics as a phase, or additional tool, in geological or exploration engineering.

Aug 1, 1956

By Jaime Guzman

Mineral exploration decision problems involve the economic evaluation of upgraded geological information and the costs of obtaining it. This paper presents a valuation theory of risky projects applicable to the analysis of exploration investments. The valuation model is predicated on the Capital Asset Pricing Model (CAPM) from financial economics; its parameters can be objectively measured from publicly available information. Geostatistics is used to derive simplified random cash flow models which incorporate the impact of improved deposit knowledge in terms of reduced estimation variance. The application of the theory is illustrated by means of hypothetical exploration optimization examples.

Jan 1, 1986

By Stephen John Brace

Increasingly, electronic blast initiation systems are being made available to the mining and construction community, both in South Africa and internationally. Indeed, in some parts of the world, perhaps half a dozen electronic products are being used, with a choice also of shock tube, electric and fuse and igniter cord systems. As these developments have taken place, improvements have been made in safety, reliability and accuracy, so much so that high performances in all these areas are now expected. However, disadvantages often seen by customers, other than : higher price, are decreased user-friendliness and loss of flexibility.

Jan 1, 1998

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

By R. N. Rothan, V. Khunova, C. M. Liauw, G. C. Lees

The interphase modification activity of 1,3-phenylene dimaleimide (also known as m-phenylene bismaleimide (BMI)) has been studied in composites based on magnesium hydroxide (60% w/w) and a polypropylene block copolymer (PPBC) that featured an ethylene-rich elastomeric impact modifier phase. BMI was found to be a unique product that led to significant simultaneous improvements in composite strength and toughness, even at the high filler levels. BMI modification was found to promote encapsulation of filler particles with the elastomeric phase of the PPBC together with formation of a PP boundary layer of increased crystalline content.

Jan 1, 2003

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By David A. Milligan

This paper outlines the research and development of a process to treat flotation tailings from the Darwin mill in lnyo County, California. A flowsheet was developed incorporating an agglomerated heap leach process using sodium cyanide to extract the silver values. Agglomeration was the key to developing this resource as the mill tailings averaged only 13% plus 100 mesh. Percolation through the heap would have been impossible without agglomeration to improve the permeability. The various tests that went into this research program are described with particular emphasis on the agglomeration techniques developed at the Anaconda Minerals Research Center. Start up and operation are discussed.

Jan 1, 1984

By M. K. Matthews

The use of backfill has important environmental control implications which, although frequently overlooked, can be both beneficial and problematical. Where backfill is widely used, the reduction in stope heat load and improved air utilization influence the overall mine ventilation and refrigeration requirements significantly. A programme of work examining in detail all the environmental consequences of backfilling is currently underway at the Environmental Engineering Laboratory of the Research Organization of the Chamber of Mines. This paper gives an overview of the work and presents some findings. In so doing, the environmental implications to be considered when backfilling are highlighted.

Jan 1, 1988

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By D. M. Smith, M. J. Meulendyke, P. J. Moroz

An extensive program of marked ball wear testing (MBWT), laboratory corrosion studies, and worn ball surface analyses has been used to gain insight about the role of corrosion in the overall wear process. In some environments, localized corrosion is observed; the actual wear mechanisms in such cases are pitting/spalling and abrasion. Factors affecting the occurrence of pitting include the abrasiveness of the ore, corrosivity of the slurry, corrosion resistance of the media, and galvanic coupling effects. Elimination of pitting substantially improves overall wear resistance. When pitting is not observed, the contributions of general corrosion are significantly less.

Jan 1, 1988

By K Dagdelen

A vehicle proximity warning system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two an a half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH funded project and discusses the GPS accuracy tests and overall system tests that were carried out during 2001 at the Morenci open pit copper mine in Arizona.

Jan 1, 2003

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By C Fearon

This paper discusses the implementation of an underground rail haulage system during a major expansion of the Olympic Dam mine in 1998. The factors affecting the selection of rail haulage are discussed and details are provided on the rail system, which is designed to transport more than 10.5 million tonnes per annum (Mtpa). The reliability of the system during commissioning is discussed, including the decision to manufacture a ædummyÆ locomotive in order to keep the system operational. Finally, reliability improvements made both during and after commissioning are discussed with comments provided on the effectiveness of the system as it operates today.

Jan 1, 2005

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980