Search Documents

By Warren J. Bruckard, Mark I. Pownceby, Sazzad Ahmad, M. Akbar Rhamdhani

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Jan 1, 2015

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By Melvin H. Podwysocki

Lineament and fracture analysis have enjoyed a resurgence of interest over the last several years, particularly since the advent of the Landsat series of Earth resources satellites. Some applications for lineament analysis include mineral, petroleum and ground- water exploration, engineering studies such as highway routing, mine roof stability, dam and power plant siting and general tectonic studies. The needs of each study may be different, but the general problem of large masses of data is common to all. Methods for efficient handling of the information and some statistical methods for its evaluation are discussed. These include comparing the lengths of the fracture population against known distributions, trend surface analysis of fracture lengths and number per unit area and multivariate analysis of rose diagrams. Examples are shown in an experimental program for predicting the presence of reef structures, areas of potential petroleum production.

Jan 1, 1977

By Y. J. Wang

The concept of subsystem characteristic curves for multiple-fan ventilation networks is presented through the construction of characteristic curves for two-fan, series-parallel networks. By considering fans as the individual network branches, the multiple-fan network is viewed as consisting of two components: any one fan branch, which is called the reference fan branch, and its associated subsystem. Thus, F subsystems can be designated for the network with F fan branches. Each subsystem contains one or more fan branches. The subsystem characteristic curve is the pressure-vs.-quantity curve of the subsystem. As illustrated in the example networks, the subsystem characteristic curve is not a strictly increasing curve and does not pass through the origin. The intersection of the characteristic curves for the subsystem and the reference fan branch represents an operating point. Multiple intersections therefore represent multiple operating points.

Jan 1, 1994

By E. K. Albert

Title IV of the 1977 Surface Mining Control and Reclamation Act (SMCRA) provides for an abandoned mine reclamation fund. This fund, taken from fees collected from operating coal mines, provides capital for the reclamation process. The Act directs the Office of Surface Mining (OSM) to collect the fees based on coal production. Monies from the abandoned mine lands (AML) fund are distributed through two programs. The first provides OSM with capital to use in emergency situations resulting from abandoned mine sites and reclaiming high priority sites in states without established AML programs. The second distributes the money through a state's AML program in the form of grants. To provide for a flexible and customized selection procedure for AML projects, a management information system (MIS) that combines scientific selection procedures is being developed. This system employs objective and subjective methods developed in systems research in recent years. The MIS component is an essential part of any selection process involving large numbers of potential projects. It must contain all the necessary project parameters that can be applied to the selection of projects whether or not they are to be used in the immediate selection criteria. In addition, variable selection criteria will allow ‘what if’ types of inquiries for comparison of differing selections and benefits.

Jan 1, 1990

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

An abstract of a paper from the Canadian Mining and Metallurgical Bulletin of August 1978 by E. Stamboliadis, J. McHardy, T. M. Salman, Department of Mining and Metallurgical Engineering, McGill University, Montreal, Quebec, states that: “The recovery of gold, silver and other heavy metal cyanides from mill solutions is technically possible using the ion exchange technique. However, the costs involved are greater than the costs of the zinc precipitation technique used for gold recovery. There are two main reasons for this: one, the fact that in gold ore cyanidation metal cyanides other than gold and silver occupy most of the resin capacity and hence reduce the adsorption efficiency of the resin for the Au and Ag cyanides; secondly, the high cost of the eluting agents.” Resin, therefore, cannot in most cases be efficiently used for recovery of precious metals. With copper in solution, only 1.47% of the resin capacity is used for gold and 0. 8970 for silver; the rest is occupied by unwanted metal cyanides, such as copper occupying 73.7%. On the other hand, although activated carbon will adsorb copper cyanides, they will be preferentially displaced by gold and silver cyanides. Ion exchange is by one or two orders of magnitude more expensive than the conventional method of zinc precipitation. The cost of removing impurities, such as copper from the resin, is greater than the cost of recovering gold. With an oxide ore amenable to cyanidation and with a low content of other metals, such as may occur with some of the Soviet gold deposits, ion exchange would be an efficient as Carbon-In-Pulp.

Jan 1, 1981

By A. Nhasengo

Paper written on project work carried out in partial fulfilment of B. sc. Eng (Mining Engineering) The purpose of this investigation was to assess the mining strategy for steep reefs at Mine A mine in 2005 and 2006. Reefs steeper than 35° were discovered when production commenced at the mine. At that time reefs steeper than 35° were not popular in South African tabular gold mines, therefore new techniques of mining them had to be developed. The underhand mining method was chosen for this purpose. The project was about assessing ventilation, support costs, local support cycles, adherence to the mine?s support standards, mine planning and efficiencies of the underhand mining method. The project work was covered by doing a literature research for underhand mining methods and performing a literature review of the mining methods, support methods, ventilation standards at Mine A. Underground visits were conducted at Mine A mine for data collection, and Mine B was visited to obtain information on support costs and efficiencies. During the investigation it was realized that the underhand mining method was an appropriate method for mining steep reefs; however, there were some challenges related to ventilation and support installation. Efficiencies could be realized with the underhand mining method and planning and scheduling were not different from breast mining.

Jan 1, 2007

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined to determine through evaluations in two mining companies whether it would achieve measurable improvements. This volume describes the model, how it was applied in the field, and how it was evaluated. Anecdotal data to illustrate common kinds of safety problems and their solutions are included. The literature and field research that preceded the model definition is discussed in Vol. 2, which covers the period of September, 1980 to September, 1981.

Jan 1, 1983

By A Jewbali, R Perry, R Inglis, L Allen

"The use of conditional simulation to characterise mine plan uncertainty is increasing for the assessment of risk in mining projects. While the development of grade uncertainty profiles is relatively straightforward and can be validated using standard geostatistical techniques, the addition of geological uncertainty to evaluate total risk remains problematic. Some of the problems associated with geological uncertainty methods include the clustering of data in favourable geologic units, difficulty in training image definition and the inability to address change of support issues for categorical variables. Despite these obstacles, the importance of geological uncertainty as a contributor to total uncertainty has prompted Newmont to explore and evaluate the use of various techniques (and combinations of techniques) on different deposit types.Two orogenic deposits of different geological complexity were selected for the study: Subika, a shear zone-hosted deposit, and Merian, a deposit containing gold mineralisation associated with quartz vein zones and stockwork within which are found higher-grade quartz breccia zones. Newmont trialled various categorical simulation approaches to determine the applicability of these methods for each deposit type and the effect of parameter choice on the width of the uncertainty interval. Some of the techniques that were trialled include multiple point statistics methods, sequential indicator simulation using local probabilities as well as variations of these methodologies.The goals of this study included: gaining an understanding of which techniques may work best in which deposit types gaining an understanding of the intricacies of each method gaining an understanding of the effect that each method has on total uncertainty analysis.This paper presents a comparison of the various techniques and makes recommendations for their use in uncertainty analysis.CITATION:Jewbali, A, Perry, R, Allen, L and Inglis, R, 2014. Applicability of categorical simulation methods for assessment of mine plan risk, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 85–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By R. E. Delavault, H. V. Warren

In normal soils there are usually 10 to 50 parts of copper in every million parts of .soil. Only 0.2 to .5 pct of this copper can be found by any simple cold chemical attack. Now, with rubeanic mid reagent paper, a prospector or field geologist can detect as little us 4 ppm of readily available copper ill soil. This degree, of sensiticity is enough to determine the presence. of copper anamalous an as and, ecentually, to discouer copper mineralization. Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit." It is sensitive, easily de- • Ed. Note: Persons Interested in purchasing kits suitable for rubeanic acid prospecting can obtain information by writing Eldrico Geophysical Sales Ltd., 633 Hornby Street. Vancouver 1, B.C. The University of British Columbia does not produce these kits for sale and has no financial interest in their production tecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream. In Brief: Testing for copper may be done easily by shaking a soil sample with strong acetic solution in a small test tube and pouring the mud into a small filter, the tip of which rests upon a strip of reagent paper impregnated with rubeanic acid (di-thio-oxamide). When copper is present—and only when it is—a blue spot develops. The more copper, the darker the spot. If the copper content is merely the small amount present everywhere, there is a pale blue or hardly visible spot; if it is abnormally high, the spot will be dark. There are, of course, intermediate cases where the experienced geochemist cannot tell offhand whether a medium-strength spot represents rich agricultural soil, weak copper mineralization, or distant rich copper mineralization. Reagents and material are inexpensive; the test may be readily done on the spot with a simple kit easy to pack and handle. Anyone interested in general problems of soil sampling as applied to prospecting may refer to an article recently presented to the AIME. In exploration work it is the contrast between the metal content of anomalous and background areas that is important; absolute values become of greater interest when an anomalous area is being investigated in detail. With specific reference to copper, it has been the authors' experience that the amounts of metal extracted from anomalous and normal soils with buffer solutions of decreasing pH show better contrast if an acid reagent is used. This contrast tends to increase with increasing acidity until 3 to 4 pH is reached. Using a short cold attack on unheated soil, it has been found that further increases in acidity do not produce better results, and only increase the hazards involved in carrying strong acids. An acidity of about pH 4 is satisfactory for direct determination of copper by dithizone. But dithizone itself introduces some problems: it must be made up fresh at frequent intervals, and with some soils, notably those with much ferric iron, oxidation mag take place before all the copper has reacted with the dithizone. Rubeanic acid keeps its strength unimpaired for long periods, is unaffected by oxidation, and is practically specific for copper at pH 4. Consequently it seems an ideal reagent to use in prospecting for copper. History and Background: Rubeanic acid (systematic name: dithio-oxamide (SC-NH2) has long been known as a spot test reagent for some heavy metals with which it gives a number of compounds. Only copper and some metals of the platinum family are believed capable of providing any ru-beanate compounds under conditions of moderate

Jan 1, 1959

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof-bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60% and 40%, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert and a rigid insert for cleaning the roof-bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the workers coveralls when using either of the inserts.

Jan 1, 2003

By Masaru Kato

The plated gold being used by the electronics industry can be broadly classified into two categories: soft gold and hard gold. Soft gold is used for circuit metallization and for bonding semiconductor chips, while hard gold is indispensable as the contact material on electrical connectors, electromechanical relays, and printed circuit boards. The traditional baths from which to plate soft gold as well as hard gold contain the cyanide complex, [Au(CN)2]-, as the source of gold, which liberates free cyanide ions during the plating. The free cyanide is not only highly toxic but also attacks photoresists used to delineate circuit patterns and bonding pads. For these reasons, non-cyanide baths are in use to plate soft gold, whereas hard gold can be plated only from cyanide baths at present. In this presentation, the current status of both electrolytic and electroless non-cyanide processes for plating soft gold will be reviewed.

Oct 1, 2003

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By De Carvalho J

The average installed refrigeration capacity on South African gold mines has increased by about eighteen per cent annually for the past 15 years; both the number of installations and their duties have increased. One consequence of these large refrigeration installations is that careful attention must be paid to the system for distributing cold water. In these distribution systems, devices which minimize the temperature rise of the water delivered to the underground workings and which also reduce the pumping requirements for returning the water back to surface are used. In this paper the suitability of these various devices are examined and with the aid of a specially developed computer program their optimum operating conditions are determined. In addition the optimum combination of surface and underground refrigeration plants is examined for a hypothetical mine at various depths and the importance of pump efficiency on total distribution costs is discussed.

Jan 1, 1988

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012