Search Documents

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled 'Steel Mine Timbers.' " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled 'Steel Mine Timbers.' " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By W. F. Wheeler

A discussion of the paper of W. F. Wheeler, presented at the Toronto Meeting, July, 1907 (Trans., xxxviii., 621 to 632). A. BEMENT, Chicago, Ill. (communication to the Secretary*):¬Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible,", not-withstanding that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combustion-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term ." combustible" was an advance to be credited to the engineer .rather than to the chemist, because the latter, not having to do with the interpretation of analysis in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression " pure coal," which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Sep 1, 1908

By C Linklater, J Chapman, A Watson

Closure options under consideration at some sites include backfilling mined-out pits with waste rock. Backfill may include mineralised and non-mineralised waste rock. Following groundwater rebound, flow-through conditions may develop in the pit post-closure. The backfill located in the saturated zone below the water table may release solutes under such conditions. It is therefore important to understand the potential impacts that backfilled pits could have on postclosure groundwater quality.Geochemical characterisation programs are the foundation for assessing the potential chemistry of water that has contacted mined wastes. Such programs must be designed to obtain data relevant to the closure options under consideration. To complement standard testing techniques, SRK utilises saturated column testing designed to generate data on leaching rates under anoxic conditions that could be encountered within submerged backfill.This paper presents the findings of saturated column test work carried out on waste rock samples from an iron ore mine in the Pilbara.CITATION:Watson, A, Linklater, C and Chapman, J, 2016. Backfilled pits – laboratory-scale tests for assessing impacts on groundwater quality, in Proceedings Life-of-Mine 2016 Conference , pp 110–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Henley S

The year 2000 is not very far ahead - only five years. It should not be hard to forecast what will happen between now and then, because the technologies that will be in practical use then should all be at least in embryo existence now. There has been a historical trend for the mining industry to work ever more difficult and ever more marginal deposits. There are clearly a few exceptions and major discoveries, but the industry is becoming heavily dependent, at both the exploration and the mining stages, on technological innovation to retain acceptable profit margins. With the new exploration and mining technologies come requirements for additional computing support. Computing technology further allows the potential integration of a wide variety of different types of data to help the explorationist to build and test exploration strategies, or to help the miner to design and schedule mining operations.

Jan 1, 1995

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

By R Simonato

It is now recognised that rotary sample division is by far the best laboratory tool for extracting subsamples from a lot of material. In terms of sampling theory, rotary division, by virtue of the fact that it can extract many increments from the lot during the division process, radically reduces the variance due to distributional heterogeneity in the sample being divided. There are a number of occasions in sample preparation when it is necessary to extract a subsample of a target mass. To do this with rotary dividers taking a fixed fraction of the starting mass is a tedious task. In response to this problem, a variable split sample divider has been designed and built for the mineral industry. This paper discusses the utility of the device and presents test data showing that the machine is capable of making accurate mass split while overcoming segregation in the material being divided.

Jan 1, 2008

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

By H. P. Schlanger, L. Paterson, B. H. G. Brady, B. E. Hobbs

A novel principle for a waste repository, based on a backfilled thermosyphon as the functional unit, is proposed. Such a unit reduces temperatures and temperature gradients in the vicinity of a waste package and in the repository near field, reducing leach rates from packages and thermomechanical disturbance of the rock mass. Preliminary analyses confirm the mode of performance of the system, and reveal some interesting features of material transport and sealing in backfill and rock fissures. The thermosyphon combines attractively with the prospect of developing a near-field geochemical trap with chemical specificity for radionuclides. It is proposed that a thermosyphon repository may provide superior performance of engineered and natural barriers compared with conventional designs. The achievement of the ability to predict accurately the performance of the thermosyphon, relative to other isolation schemes, will represent a benchmark in the understanding of the absolute performance of any repository.

Jan 1, 1986

By Ken Major, Anita Marks, Craig Sams

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By David R. Maneval, Sylvester Lemezis

All acid mine drain waters, regardless of source, share certain characteristics; but they do differ in exact chemical composition, degree of acidity, and total solids content. Any serious program to treat such waters must recognize these differences and apply to each specific case the technique which offers the best promise of each specific case the technique which offers the best promise of technical and economic success. The Pennsylvania Dept. of Mines and Mineral Industries has originated and funded studies of many different treatment means. Neutralization with lime is now being used on 200 different polluted streams in Pennsylvania, and multistage flash evaporation has been selected for a particularly large and troublesome outfall near Wilkes-Barre, Pa. A 5 x 106 gpd plant for this latter site is now being designed by Westinghouse Electric Corp. which developed a concentration process based on multistage flash evaporation as part of the State's research program.

Jan 1, 1973

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll' in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod'. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By P. G. West-Sells

At Barrick's Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By M. Girardeau, J. Blondin, M. Nomine

It is well known that surface moisture and fine content have a strong influence on coal handle- ability. It is known as well that these two criteria are not sufficient to classify coals. It seems that certain types of coals are intrinsically difficult to handle, the reason being still not well understood. For these coals, moisture and fine content are aggravating factors and have to be strictly controlled in order to avoid handling problems (sticking, arching in hoppers.. .). CERCHAR has undertaken research aimed at identifying the role of intrinsic characteristics of coal with regard to handling properties. Two of them have been identified as particularly relevant : the clay content and the "colloidal particle" content. Two simple tests commonly used for soils characterisation, but never used so far for coal, have been applied to characterise a wide range of coals. The derived classification has been compared with an empirical classification based on dry screening tests. DRY SCREENING EXPERIMENTS Dry screening at a relatively low screen aperture (e.g. 6 mm) may be considered as a good tool for assessing the handleability of wet fine coals. Difficult to handle coals always lead to rapid plugging of the screen whilst easy to handle coals can be screened without difficulties. A wide range of coals has been selected with various ash, moisture and fine content. Their characteristics are given in table 1. The experimental set-up consists of a 2 t.p.h vibrating screen equipped with two automatic re- cording balances collecting respectively oversize and undersize material. Provided that the feeding rate is accurately controlled, good reproducibility in the percentage passing as a function of time is obtained. Figure 1 gives examples of different types of relations that were obtained. - LMC coal exhibits a behaviour that is characteristic of easy to handle coals : % passing remains constant in the course of the screening operation. - B coal behaves slightly differently. One observe first a rapid decrease in the flow passing through the screen and then a stabilization. Hand- ling properties can be considered as intermediately - The curve relative to LHB coal is characteristic of a very difficult to handle coal that blinds the screen almost immediately. It is necessary to point out the fact that the classification derived from screening experiments is a global one, including not only intrinsic factors but also external factors such as fines and moisture content. The role of surface moisture is in particular very important and variations in this parameter may upset the empirical classification

Jan 1, 1988

By A. E. Back, K. E. Tame, W. F. Wyman, S. F. Ravitz

IN 1940, when it appeared that the United States soon might be cut off from foreign sources of high-grade manganese ore, the Bureau of Mines began an extensive series of investigations on the production of ferrgrade products from low-grade domestic ores by ore-dressing, pyrometallurgical, and hydrometallurgical methods. Among the hydrometallurgical processes for oxide ores investigated was a sulphur dioxide process in which the manganese was recovered from solution by precipitation with lime;1 this process is essentially as follows: The ground ore is suspended in water and leached with SO2 gas to extract the manganese as manganese sulphate. Calcium chloride is then added to the slurry to precipitate calcium sulphate and form manganous chloride solution, and the resultant slurry is filtered to remove the calcium sulphate together with the in- soluble portion of the ore. Calcium hydroxide is added to the filtrate and the mixture is agitated with air to precipitate hydrated oxides of manganese and regenerate calcium chloride. The precipitate is calcined, and the calcium chloride is recycled. To determine manganese extraction, reagent consumption, grade of product, and similar data for this process, a laboratory investigation was started. Two minor modifications in the process were soon made: (I) the ore was suspended in calcium chloride solution instead of in water in order to extract the manganese and precipitate the calcium sulphate in one step, and (2) the agitation with air after the addition of slaked lime to the filtrate was omitted because manganese hydroxide is readily precipitated without air agitation and can be nodulized or sintered to a satisfactory product. When the process was carried through a series of cyclic tests, it was noted that the concentration of dithionate ion (which is one of the products of oxidation of SO2 by MnOz) in the cycled solution gradually increased; at the same time the chloride content of the solution gradually decreased, owing to soluble losses in the leach residue and in the precipitate. After a number of cycles, the calcium chloride became virtually completely replaced by calcium dithionate, the quantity of dithionate ion formed during the leach being more than enough to make up for the losses of dithionate in filtering. The calcium chloride process thus developed into a calcium dithionate process. Since the latter eliminated the need for make-up calcium chloride, and the dithionate solutions appeared much less corrosive than the chloride solutions, work on the calcium chloride process was dropped in favor of the calcium dithionate process. ACKNOWLEDGMENTS The dithionate process was developed by the Bureau of Mines as part of a

Jan 1, 1946

By A. K. Knickerbocker

Practically all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day's pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatis. faction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called "contract " system is not a contract and the name is a misnomer. No true contractual obligation exists. As usually practised, the contract system involves the setting of a price per foot in development work, or per foot or per car, usually the latter, in slicing or stoping, by the mining captain, and assumes its acceptance, though often under protest, by the men. A price is set for each working place, in which there are usually two men per shift. This price includes labor and supplies, such as explosives, fuse and caps, shovels, carbide, etc., and the men divide the total earnings less the amount expended for supplies. The cost of the supplies charged to the men varies

Jan 1, 1920

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009