Search Documents

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By George D. Haley

This report will be given in two sections. The first sec¬tion outlines techniques and equipment to form almond shaped fluorspar briquettes by means of briquet presses, and the second section outlines techniques of the balling disc. PART I - BRIQUET PRESSES Fluorspar has been briquetted for a number of years and the so called "peach pit" briquet is known to many steelmen. Present production is estimated at over 100,000 tons annually. Slide 1 shows an assortment of various sizes and shapes of briquettes. It is possible to form fluorspar into almost any configuration of briquet. For safety on the melting floor, pillow type briquets are preferred. Ease of mechanical handling and durability of the product are facil¬itated by an almond shape. The dimensions of the almond can vary from 1-in. to 1-1/2-in. in length, from 13/16-in. to 1-in. in width and from 1/2-in. to 1-in. in thickness. The type of equipment to pro¬duce almond shaped fluorspar briquettes is shown in Slide 2. Here we have a Komarek-Greaves and Company 300 ton briquettor equipped with almond rolls. This machine is capable of producing fluorspar briquettes at a rats of 30 tons per hour with power consumption of 35 hp per ton par hour.

Jan 1, 1969

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

With the continued implementation of stricter limitations on the discharge of excess process water from all existing and future mining and metallurgical operations, the design and operation of the entire process water circuit must form an integral part of any total operational package. It is far better to æanticipate and circumvent the problemÆ rather than be forced into an expensive remediation program after the event. By far the greatest problem relates to the treatment and disposal of what is generically known as acid drainage. In simple terms, an acidic metal sulfate solution is generated by a series of chemical and biological reactions as soon as most sulfide minerals are exposed to air and water. Treatment of this solution by one or more of a wide range of chemical and physical options can involve substantial capital and operating costs, although there are recent processing options that yield saleable by-products, thereby reducing the financial liability of what is effectively a waste stream. This presentation provides an overview of the Australian situation compared with the rest of the world and outlines the basic features of a number of the more advanced passive and active acid drainage options.

Jan 1, 2004

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique. thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg-robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By Brent Blanchard

Dallas/Fort Worth Airport recently took a major step in its fiveyear expansion project with the explosive demolition of the Hyatt Regency Hotel West. Built in 1965, the Hyatt Regency held the distinction of hosting five U.S. Presidents over the years and was reportedly one of the first hotels in the world to be built within an airport’s boundaries.

Jan 1, 2003

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

Jan 1, 1918

By Lawrence C. K Hu

The release of load mechanism during rock breakage by explosives was founded by Dr. T. N. Hagan & published at the Sixth International Colloquium on Gasdynamics of Explosions and Reactive Systems Stockholm, Sweden, 1977.

Jan 1, 1995

Jan 1, 1920

[ ]

Jan 1, 1993

By Daniel W. Kappes

In late 1995 at the Randol symposium in Squaw Valley, I gave a paper which described the Itos project flowsheet. At that time, project construction was nearly completed and stmtup was close. This paper describes the ltos operation since then. To summa­rize things, startup occurred partially in late 1995 with full start­up of all components in about mid 1996. From then until now, April 1998, the plant has been running at partial capacity and has yet to achieve full production rates.

Jan 1, 1998

[ ]

Jan 1, 1938