Search Documents

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By Sen A. K

The Chiria Iron Ore deposit falls within the well-known Horse-shoe-shaped Singhbhum-Bonai-Keonjhar belt in India, where most of the deposits supplying ore to various steel works of Steel Authority of India Limited (SAIL) and Tata Iron and Steel Company (TISCO) are located. With an estimated reserve of about 2000 million tonnes of ore (at 55 per cent Fe cut-off) spread over four contiguous blocks, it is the largest iron ore deposit in India and one of the largest in world. The present study is confined to only one of the four blocks of Chiria viz North Block, comprising an area of 2.11 km2. `Corporate Plan 2005' of SAIL envisages development of a large open cast mine at Chiria to meet its enhanced requirement of iron ore by 2001-02 AD.

Jan 1, 1995

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017

Throughout October, U.S. producers priced unalloyed 99.5 percent aluminum ingot at 53¢ per pound. Dealers, in last month's domestic market, were quoting unalloyed ingot at a range of 45.5¢-46.3¢ per pound. Costa Rica recently issued a proposal to Japanese aluminum smelters to participate in an integrated aluminum-refining project which would include bauxite development. The project reportedly would include a 600,000-kilowatt hydroelectric power station, a 600,000-metric-ton-per-year alumina plant, and a 300,000-ton-per-year primary aluminum smelter. Two U.S. firms--Aluminum Co. of Amerjca (Alcoa) and Martin Marietta Co.--and several European aluminum smelters are also said to be interested in taking part in this project. Alcoa conducted a feasibility study for the Costa Rican Government in 1970 and estimated the bauxite reserves to contain 150 million metric tons.

Jan 1, 1977

By Winton J. Gale

Coal pillar design has been based on generalized formulas of the strength of the coal in a pillar and experience in localized situations. Stress measurements above and in coal pillars indicate that the actual strength and deformation of pillars vary much more than predicted by formulas. This variation is due to failure of strata surrounding coal. The pillar strength and deformation of the adjacent roadways is a function of failure in the coal and the strata about the coal. When the pillar is viewed as a system in which failure also occurs inthe strata rather than the coal only, the wide range of pillar strength characteristics found in the United Kingdom, United States, Republic of South Africa, Australia, People's Republic of China, Japan, and other countries are simply variations due to different strata-coal combinations, not different coal strengths. This paper presents the measured range of pillar strength characteristics and explains the reasons. Methods to design pillar layouts with regard to the potential strength variations due to the strata strength characteristics surrounding the seam are also presented.

Jan 5, 1999

By G. Simmons

Santa Fe Pacific Gold Corporation (SFPGC) conducted pressure oxidation pilot plant studies at Hazen Research, Inc. on the Twin Creeks refractory carbonaceous gold ores during 1993 and 1994. Previous laboratory investigations demonstrated very good gold recoveries of 90 to 95%, using CIL cyanidation after batch pressure oxidation. However, results from the pilot plant showed that several ore types responded very poorly, with gold extractions of only 45 to 75%. Since these poor recoveries were unexpected, pilot plant testing was suspended for approximately four months while extensive research activities were conducted to determine the cause(s) and identify potential solutions. This paper describes the batch and pilot plant test results, the research activities that eventually identified the cause of the gold recovery problem, and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions.

Jan 1, 1997

By Feng Liu

A thermal upgrading process by which nickel value can be concentrated in a ferronickel alloy is a possible alternative to treat Sudbury pyrrhotite (Po) tailings with nickel content of 0.5–1.5 wt%. The basis of this process is precipitation of Ni from Po at high temperature once Fe/S ratio in the iron-deficient Po is shifted towards stoichiometric or near stoichiometric FeS (troilite) either by the addition of iron and/or the removal of sulfur. For the iron addition route, the reaction between elemental iron and nickeliferous pyrrhotite to produce ferronickel alloy and Ni-depleted iron sulfide phase plays a critical rule. In this paper, the formation mechanism of ferronickel alloy was investigated using the diffusion couple technique to better understand the nickel diffusion behavior in the iron and sulfide phases.

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

Recent legislation in the environmental field gives the mining industry an opportunity to take timely action to address its image. Shifting the focus away from mining (the activity) to minerals (the resource) will enable the mining industry to stand on equal footing with other industries and will help minimise the vulnerability to political and interest groupsÆ interference.

Jan 1, 1993

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By H. O. Hofman

Jan 1, 1896

By Bernard Lewis

This report on the research and technical studies conducted by the Explosives Branch of the Bureau of Mines covers the 2-year period July 1, 1946, to June 30, 1948. A report for the fiscal year 1947 was omitted because of the large amount of work still in an unfinished state. The material presented herein is based largely upon more comprehensive reports prepared under the authorship of members of the branch staff.

Jan 1, 1949

When overburden depth exceeds economical recovery in openpit coal mines, the use of highwall mining systems has increasingly come into play. However, stability in the highwalls is always a major safety concern during such mining. The U.S. Mine Safety and Health Administration requires that highwall mining operators follow ground control plans that specify the pillar sizes necessary to prevent collapse that would threaten highwall stability.

Jan 1, 2006

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

By Robert W. Carn

This paper presents the concepts which are presently being utilized in the design of coal export terminals. Criteria for selecting a viable site and establishing the terminal plan are presented. Factors affecting the design of the terminal as well as the present techniques and procedures in use today to determine the optimum use of equipment will be discussed along with the current trends in export terminal control systems. Finally capital and operating costs for a typical export terminal are reviewed.

Jan 1, 1982

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By F. H. Buttner

Commodity currency intrigues most of us because of the problems it offers to solve for the Third and the First Worlds. What problems might be solved, if commodity currency were to be adopted in the Third World? That is really the question we are probing here right now. It would take a while to think through all their subtle consequences of this question, but, off the top, it might well have at least three important impacts. Most important of these to this audience is relief from unfair Third World competition. Second, it might well liberate Third World economies from financial indebtedness to the First World and give them freedom from the liquidity limitations. The third benefit is that it might help relieve World trade tensions. All three benefits are interrelated. We could start our speculations on the application of commodity currency from anyone of these starting points. But let us use the starting point most important to you, unfair competition to the U.S. mining industry. From there we might wind up with some thoughts on things you, yourselves, can do to improve things.

Jan 1, 1978

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945