Search Documents

By E. Shum, V. G. Papangelakis

"Attempts to reduce the energy requirements of water recovery in the process industries have resulted in the development of techniques to freeze and purify aqueous solutions that take advantage of local climatic conditions. Natural freezing is a technique by which aqueous solution is exposed to freezing air temperatures, resulting in the production of a layer of ice on the surface. As the ice layer tends to exclude solute, a concentrated solution is formed. However, due to dendritic ice growth along the advancing growth front, small quantities of solution are trapped within the ice, decreasing the purity of the water recovered. The ice produced can then be allowed to thaw in order to recover the water using low grade plant heat. As the more concentrated parts of the ice melt first, a purer ice remains. In this study, 0.5 molal magnesium sulfate solution was frozen under simulated natural freezing conditions at temperatures between –1 and –6°C. The ice produced was thawed at either room temperature or 50°C. Up to 40% of the water was recovered with a separation efficiency of above 95% when thawing at room temperature.INTRODUCTION Advances in refrigeration technology have made low-temperature separation processes increasingly appealing to an energy-conscious society. The latent heat of freezing of water is about seven times smaller than the latent heat of evaporation providing freezing with a strong thermodynamic advantage over the traditional evaporation-based processes. The result is the development of a wide variety of processes that fall under the term Freeze Concentration (FC), which describes a variety of techniques in which an aqueous solution is concentrated by the creation and subsequent removal of ice (Williams et al., 2015).FC processes exploit the freezing behaviour of aqueous solutions as dictated by their respective water-salt phase diagram. When, for example, a solution of magnesium sulfate is cooled to a temperature below its freezing point but above its eutectic temperature of –4.1?C (Figure 1) then, if the concentration of MgSO4 is less than the eutectic concentration (about 1.7 m), ice will form until the solution concentration reaches its equilibrium concentration at the given temperature on its phase diagram. If the concentration is greater than the eutectic concentration, MgSO4 solid will precipitate until the concentration reaches equilibrium. It is for this reason that ice can be selectively produced in FC processes (Randall & Nathoo, 2015)."

Jan 1, 2017

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

By A-A. Bogno, M. Rappaz, J. Valloton, H. Henein

"Rapid solidification of Al-Cu droplets of eutectic composition was carried out using Impulse Atomization in an argon atmosphere, to study the microstructures forming at different cooling rates and undercoolings. Two distinct morphologies were observed within the investigated Al-33wt%Cu droplets microstructures: (i) A regular lamellar morphology and (ii) an undulated morphology. The volume fraction of each type of morphology was measured as a function of the droplet size and the nucleation undercooling was deduced using the hypercooling limit equation. The scale of the microstructures was determined through measurements of inter-lamellar spacing across and along the growth direction. Growth velocity and undercooling were deduced using Jackson and Hunt (1966) eutectic growth theory. Finally, mechanical properties were estimated through micro-hardness analysis using a Vickers hardness tester, revealing exceptional properties for an aluminum-copper alloy. Indeed, the hardness values, increasing with growth rate and undercooling, were 3 times higher than the values obtained in hypo-eutectic Al-Cu alloys.INTRODUCTION Eutectic alloys are very attractive due to their good fluidity allowing ready shaping of parts in casting processes as well as in thermal spray deposition. In addition, they yield microstructures with high mechanical properties, by the virtue of their scale/size which is defined by the solidification parameters and the thermodynamic and thermophysical properties of the given alloy. Therefore, it is important to understand the relationship between the microstructures and the solidification parameters of eutectic alloys in order to control their solidification path and mechanical properties. The latter could be improved by either adding an appropriate strengthening component to a base eutectic material (Böyük, MaraslI, Kaya, ÇadIrlI, & Keslioglu, 2009) or by refining the microstructures for more effective dislocation pinning (Campbell & Campbell, 2003). Tailoring the microstructure can also be beneficial to chemical (Freitas, Osório, Spinelli, & Garcia, 2014; Osório, Freire, Caram, & Garcia, 2012) or electrical (Kaya, 2012) properties of the material. Eutectic-type microstructures, usually formed from liquid (eutectic transformation) or solid (eutectoid transformation), are made up of two or more different phases, generally of lamellar or fibrous (rod like) morphologies (Kurz & Fisher, 1998). In general, a binary eutectic structure can be regular (when both phases are non-faceted) or irregular (one of the two phases is faceted), the two solid phases having roughly the composition of the liquid from which they are formed."

Jan 1, 2017

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

By Xueming Lv

The rotary kiln-electric furnace (RKEF) process is the main method for producing ferronickel from nickel laterite ore. However, this process is energy intensive as it involves several high temperature steps. Therefore, a novel process is proposed to directly produce ferronickel from nickel laterite ore by semi-molten reduction, which is expected to be realized in a rotary hearth furnace (RHF). The RHF process is able to shorten the flow sheet, decrease the reaction temperature as well as reduce energy consumption. In this study, the influence of basicity on reduction of nickel laterite ore was investigated. The results showed that it is possible to produce the ferronickel nugget directly at 1400 °C when the quaternary basicity [(mCaO + mMgO)/(mSiO2 + mAl2O3)] was fixed at 0.60. Under this experimental condition, the grade and the recovery ratio of nickel reached 11.53% and 98.59%, and the grade and recovery ratio of Fe were 84.16% and 68.72%, respectively.

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By B. W. Moore

The U.S. Bureau of Mines investigated the separation of heavy rare-earth elements (REE) in an ion-exchange process. An ion-exchange column consisting of two sections, a loading section and a separation section, provides high levels of REE loading and good REE separation with an expected processing cycle of less than a month, while current ion-exchange technology requires more than 5 months. A different resin is used in each section: sulfonic resin in the loading section and iminodiacetic resin in the separation section. The separation section is further divided into two segments: the first conditioned with NH4 and the second with acid. Erbium is loaded onto both segments of the separation column as a retaining ion. Bands of mixed REB eluting between separated bands of pure REB were recycled directly to the column. Without mixed-band recycle, over 80% of the REE eluted from the column was separated into fractions with 99% purity of each element; with such recycle, the percentage of separated elements can be increased to around 90%.

Jan 1, 2010

By J. E. Warren, J. H. Hartsock

Because of the extensive utilization of hydraulic fracturing for the stimulation of low-productivity wells, the two related problems of fracture design and evaluation have become economically significant and, as a consequence, helve motivated this investigation. The producing characteristics of horizontally fractured wells were studied to determine the fracture configuration that should be employed as the basis for the design of the treatment and to develop a method that can be used to establish the degree to which the design objectives have been achieved. The equations which describe the steady-state flow of a single-phase fluid into, and through. a finite-capacity fracture were solved numerically for an idealized reservoir-fracture model. The numerical results were used to obtain an apparent skin effect for each combination of the parameters considered. Based on the computed results, subject to the limitcitions implied by the assumptions that were made, the following general conclusions were drawn. 1. For a radius of drainage at least four times us large as the radius of the fracture, an apparent skin effect that is independent of the radius of drainage can be calculated. 2. The productivity of the hydraulically fractured system, relative to that of the unfructured well, can be determined from the apparent skin effect and can be used to establish design objectives. 3. In the evaluation of a fracture job, it is not Possible to determine both the radius of the fracture and its flow capacity uniquely from the apparent skin effect; an independent determination of one of the quantities is necessary. lNTRODUCTION Although hydraulic fracturing has been employed as a method for stimulating the productivity of literally hundreds of thousands of wells during the past 10 years, it is only in the last few years that improvements in fracture design1-6 and fracturing technique' have combined to increase the probability of obtaining a successful treatment to such an extent that the mechanics of the method may be considered to be standardized. From an economic point of view, however, two related questions must be satisfactorily answered before hydraulic fracturing can be used in the most profitable manner. The two questions are the following. I. For a particular well in a given formation, what are the optimum design specifications for the fracture treatment? 2. Have the design objectives been achieved by the fracture treatment? The significance of these questions has been recoguized, and some attempts to obtain answers have been made. Howard, et al,8 endeavored to determine the optimum treatment, based on maximizing profits, for any given formation; unfortunately, this work was based on a crude method for approximating the productivity of a well. Carter and Tracy9 utilized the same approximation to study the effect of fracturing on the behavior of a well producing by virtue of a solution-gas drive. Electrolytic models were used by van Poollen10 to investigate the variation in productivity due to fracturing; however, only a limited number of results were presented. Later, from the same model results, van Poollen, et al,11 attempted to justify an approximate expression for determining the productivity of a fractured well. It is quite apparent that there is a definite lack of the practical information necessary for specifying the optimum fracture configuration to be considered for design purposes. The only detailed attempt to develop a procedure for evaluating the result of a given fracture treatment appears to be that of van Dam and Horner.12 These authors described a technique for analyzing pressure build-down data, obtained immediately after fracturing, to determine the final fracture volume, the final fracture porosity, the fracture area, the fracture thickness and the in situ fluid loss of the fracturing fluid. While this approach should be useful whenever acceptable pressure measurements are available, it does not yield a value for the flow capacity of the fracture. Since the problems of fracture design and evaluation are inversely related, it should be sufficient to study the effect of the fracture configuration on the performance of a well. The primary objective of this investigation is to evolve a technique for computing the desired solutions. The secondary objective is to analyze these computed results in order to prescribe a method for evaluating fracture treatments. Because this study is exploratory in nature, its scope

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By P. G. Henderson, G. C. Thompson

The organization and mechanized colliery management of a large by G. C. THOMPSON, B.Sc. (Min. Eng.) (Witwatersrand), M.B.L. (Member), and P. G. HENDERSON, B.Sc. (Min. Eng.) (Pretoria), M.B.A. (Member). Usutu Collieries Limited, at present the largest single producer of coal in South Africa, supplies Cam den power station. and produces 435 000 tonnes per month by conventional mechanized methods from bord-and-pillar workings in three mines. The thickness of the seams averages 2 metres, and the depth below surface varies from 15 to 150 metres. Each mine depends to a different extent on certain common facilities and services. Two of the mines are located on the same coalfield, and their rationalization would possibly be advantageous. Production policy is one of productivity with flexibility. The double-loader system is widely used, and one section at each mine is worked on single shift. Pillar extraction is practised where possible. In addition to lubrication and inspections, planned maintenance of mining equipment consists of sub-assembly replacements and overhauls. Conveyor and tractor/trailer transport is used underground. but trolley-wire locomotive haulage is being considered. The organization is such that co-ordination is relatively difficult, and certain changes could possibly improve the functioning of the engineering and mining departments. Technical and management training is carried out. Long-term planning will make use of a computer programme and will involve the investigation of other mining methods. Five-year and twelve-month plans are prepared, the planning of coal quality being based on the view that the mine and the power station together constitute a system. Control information systems make use of a remote computer terminal located at the mine. An improved integrated system is being investigated.

Jan 3, 1975

By Dingwu Feng, Jannie S. J. van Deventer

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated by using an ultrasonic probe in two slurry systems, i.e. cyanidation of a refractory sulphide ore and geopolymerisation of metakaolinite. The surfactant dithiophosphate was used to render the gold bearing sulphide particles hydrophobic, in an attempt to induce the formation of cavitation bubbles directly at the desired surfaces. Oxygen was injected into the cyanidation system to improve the attachment of oxygen bubbles to the hydrophobic sulphide surfaces. Geopolymerisation occurs in highly alkaline solution with waste aluminosilicate oxides and silicates as the reactants. The process of geopolymerisation is believed to involve dissolution of Al-Si oxides from solid particles, diffusion of dissolved Al-Si complex from the solid surface into the gel phase, condensation of gel phase and hardening of the gel phase. It has never been investigated how ultrasonication affects the above steps in synthesising geopolymers, despite a number of papers dealing with sonochemical synthesis of materials. The introduction of power ultrasound into such slurry systems is expected to result in advanced geopolymer materials.In the cyanidation of the pyrite concentrate, the kinetics of gold extraction were significantly enhanced in the presence of ultrasound, due to the prevention of passivation and the enhanced dissolution of sulphides. Cyanide consumption was significantly reduced with ultrasonication, owing to the oxidation of soluble sulphides to sulphate, minimising the cyanide consumption by sulphides. With oxygen injection, ultrasound significantly enhanced the leaching of gold from the pyrite concentrate, as oxygen could enhance the formation of the oxidation radicals by ultrasonic cavitation. In the presence of dithiophosphate, ultrasound further improved gold leaching in the oxygen-aerated system. Dithiophosphate could selectively adsorb at gold host sulphide surfaces, and make the surfaces hydrophobic. As a result, the ultrasonication effectiveness could be enhanced through forming cavitation bubbles directly at the interfaces."

Jan 1, 2003

By Robert W. Baker

"Brunswick Mining and Smelting commenced production at the No. 12orebody, a lead/zinc/copper/silver deposit, situated some seventeen miles southwest of Bathurst, New Brunswick, in 1964 at 4100 tonnes per day. Today it operates at 10500 tonnes per day.Brunswick has utilized underground incentives since commencement of operations. Early incentive systems were “off the wall"" based on those in effect at other properties then manipulated to fit, often hack calculated from actual performances to tm1ve at the desired result. If subsequent payouts were considered too high the rates were simply reduced, often retroactively. A large amount of this was' subjective and depended to a large extent on whoever was handling the bonus, in conjunction with senior mine department staff.In 1971, it was' decided that a more scientific approach was needed, particularly with the introduction of the new cut-and-fill mining. After some research, a system based on Work Study was selected. Another major mining company employing such a system loaned one of their experienced employees to train some Brunswick personnel in the art of Work Study and conversion of data to incentive rates, and in 1972, the first such developed incentive rate was-introduced.Along the way, borrowing from others where necessary, a set of Brunswick principles and parameters were developed. While refined to some extent, these remain basically the same today.Improvements in methods and equipment have resulted in improved performance and reduced costs. The use of underground incentives has played an important role in this. A/though individual bonus earnings have steadily increased, bonus cost per tonne has remained nearly constant - in real dollars, it has regularly decreased. These are two of the main parameters of a successful system."

Jan 1, 1995

By Dongxu Jia, Chen Cao, Shuangwen Ma, Jun Han, Huibin Ma

Coal bump, or coal burst, is one of the catastrophic disasters in underground coalmine. Among them, approximate 80% of recorded destructive burst events were occurred in mining roadway. The bump panel is often formed by hard coal seam and hard main roof; however, the cause and course of the bump events are not understood yet. This study provides a fundamental theory for the causality and progress of a coal bump event occurred in longwall roadway. Considering hard roof condition commonly existed in bump panels, we think that the abutment pressure induced by suspended roof behind the working face is the trigger of a coal bump event occurred in the roadway. Once high abutment pressure is concentrated on the hard coal seam around the working face, the roof and the coal around the working face form a seesaw-like structure, which leads the roof in front of the working face moving upwards. The movement of roof uplifting in front of the working face is a well evidenced phenomenon in practice, namely, roof rebounding, which causes unloading of the normal stress on the roof-coal interface around the roadway. A rib coal block bump mechanical model has been developed to establish the critical equilibrium equation of the coal block. Result shows that, the force source of coal bump is the horizontal ground stress perpendicular to the rib surface; and the slippage of the coal block is caused by the unloading of the normal stress acting on the roof-coal interface. Based on the causality and consequence theory of coal bump developed in the paper, several new prediction and prevention measures have been developed, including roadway design and in-tunnel reinforcing methods. The commonly used prevention measures in present have also been discussed. This paper presents a comprehensive explanation of coal bumps occurred in longwall roadways, from abutment pressure at working face forming seesaw structure to roof rebounding leading slippage of the rib coal mass into roadway, which provides a fundamental theory for coal bump causality mechanism and prediction and prevention technology.

Apr 26, 2022

By A. B. Kinzel

ALTHOUGH vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding con-tribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type-18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted, since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents 'result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less-generally at the usual 0.65 to 0.75 per cent.

Jan 1, 1932

By Guilherme Monteiro Garcia

O resfriamento contínuo de forma controlada garante propriedades mecânicas específicas nos aços. Este trabalho apresenta melhorias feitas em um sistema de controle de resfriamento em um laminador de tiras a quente. As melhorias apresentadas garantiram uma melhora na performance de 5% de forma a reduzir drasticamente o custo da não qualidade. As modificações visaram adaptar o sistema para uma nova realidade de grandes acelerações e desacelerações da tira no trem acabador visto o aumento da produtividade e a redução do uso da coil box.

Aug 17, 2017

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018