Search Documents

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By Peiwei Hu, Min Lu, Tiejun Chen

Based on the analysis of properties of vanadium tailing (VT), the surface modification study was carried out as a polymer filler. The modification effects of the three kinds of coupling agents on VT and the mechanical properties of polypropylene (PP) composites with a modified vanadium tailing (MVT) were compared to determine the suitable surface modification agent and modification processes for VT. The results show that the best one is aluminate coupling agent DL-411. When the content is 1.2 wt% and the temperature was 100 °C, the activity index of modified vanadium tailing (MVT) is 95.53%. FTIR analysis shows that DL-411 has the strongest binding ability on VT. XRD analysis shows that VT has a heterogeneous nucleation on PP to induced b form formation, and DL-411 could enhance this nucleation. So the composites has higher strength and better toughness. When the content of MVT is 10 phr, the tensile strength, impact strength, flexural strength and flexural modulus of the composites are 47.51 MPa, 38.43 kJ/m2, 59.57 and 1654.36 MPa, respectively.

Mar 1, 2018

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By C. C. Harvey

Asia is experiencing a growth market for industrial kaolins for use in ceramics, paper, plastics and other market sectors. Export and import data for the Asian countries reflects this growth with the Peoples Republic of China as the major exporter of clays and Japan the major importer. The growth in tonnage and product sophistication of kaolins produced on Belitung in Indonesia is typical of developments that are taking place in many locations in Asia. This region therefore presents opportunities for mineral processors and a challenge for the exploration geologist, the mineral processing engineer, the mineral economist and the marketing specialist.

Jan 1, 1996

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites. The objective of this study was to compare two mines, each affected by this pillar load transfer mechanism, and to show how this interaction affected underground workings by the installing and monitoring underground instrumentation. At mine site A where the overburden was 1,000 ft, the innerburden thickness was less than a pillar width (40 to 45 ft), overlays of the mine layout show pillars were not superpositioned, excessive roof to floor convergence was measured, and pressure readings indicated pillar core loading only. At mine site B, the overburden was approximately 555 ft, the innerburden thickness was approximately 105 ft, overlays of the mine layout show pillars were superpositioned, minimal roof to floor convergence was measured, and pressure readings indicated a skin loading only.

Jan 1, 1988

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By J L. Merritt

The mining industry seeks to engage with and respond to stakeholders through open consultation processes during the various phases of a mining project (Department of Industry, Tourism and Resources, 2006). Two Australian Coal Association Research Program (ACARP) funded projects conducted in the Bowen Basin coalfields in Central Queensland investigated the use of a stakeholder panel for the evaluation of mine site rehabilitation. The panel members were drawn from the local and regional area, and represented neighbouring landholders, traditional owners, AgForce, local government, conservation groups and non-governmental organisations (NGOs) such as Greening Australia and the Fitzroy Basin Association. The approach of utilising stakeholders to establish rehabilitation criteria was proposed as an alternative to the established practice of assessing rehabilitated areas against a suite of quantitative completion criteria; eg >70 per cent vegetative ground cover or <5 t/ha/a soil loss. The basis of this approach recognises the reality that the definition of completion criteria has proved problematic over the last 40 years with no broad consensus reached on the suite, let alone the metrics; eg the exact cover level that will benchmark acceptance of the mine site rehabilitation.CITATION:Merritt, J L, 2016. Zooming out – learning to see rehabilitation through stakeholders’ eyes, in Proceedings Life-of-Mine 2016 Conference, pp 163–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Peru has become an established mining country. The industry and industry-related businesses account for a significant amount of the country´s revenue, on state and local levels. But like other countries with thriving mining industries, Peru has seen its mining industry revenues fall off in recent years due to a lackluster global economy. And the mining industry in Peru must also deal with increasing concerns about mining?s environmental impacts, local community and other social issues, as well as a regulatory environment that has placed more restrictions on what miners can do. That said, the Peruvian government is beginning to realize how important mining and natural resource development is to building the nation?s economy, improving its infrastructure and lifting its population out of poverty. The government support was evident during the Perumin 2013 mining convention, held in September in Arequipa. In addition to Peru?s President Ollanta Humala speaking at the closing ceremony, the country?s ministers of Energy and Mines, and Economy and Finance participated in the event, as well as numerous other federal and state authorities. Perumin is put on by the Instituto de Ingenieros de Minas del Peru (IIMP, or Peruvian Institute of Mine Engineers). The 31st edition of the convention, billed as the ?world?s largest mining convention? by the IIMP, this event was led by Abraham Chahuan CEO of Antamina and Romulo Mucho (SME member) as president of IIMP, attracted about 118,000 participants from more than 48 countries. This was more than the anticipated 75,000 attendance and well past the 51,000 people who attended the 2011 convention. The last edition of PERUMIN was led by the CEO of Compañía Minera Antamina, Abraham Chahuan and Rómulo Mucho (SME member) and representative of the IIMP. The event attracted more than 1,000 journalists from all over the world, the IIMP said. A total of 2,213 booths from equipment and machinery supplying companies from the five continents were present at the Mining Technology Exhibition (Extemin), including companies from the United States, Canada, China, South Africa, Germany, Australia, Brazil and Chile, among others. The convention has grown so large in recent years, that the IIMP shifted its location from Tecsup vocational school in Arequipa to the Cerro Juli Convention Center. The venue is 116 percent larger than Tecsup, the IIMP reported, covering about 20 ha (40 acres). It was reported by Latinomineria magazine that about 10 million Peruvian soles were invested in the new venue to create a world-class events center. It was also estimated that the event generated more than 234 million soles to Arequipa?s economy.

Feb 1, 2014

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By Zhouhua Jinag

The attempt has been made to manufacture high nitrogen austenitic stainless steels by pressurized electro-slag remelting furnace with maximum nitrogen pressure of 7MPa. To obtain high nitrogen content in steels, the compound electrodes with different nitrogen sources (FeCrN, Si3N4) were prepared. Using the Si3N4 as the nitrogen alloying source, the silicon contents in ingots were prone to be out of the specification range, and the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved using FeCrN as nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen above 1.0wt% could be obtained. A series of high nitrogen austenitic stainless steels have been successfully developed by this method. The mechanical and pitting corrosion resistance properties of high nitrogen austenitic stainless steels were investigated. The results show that the steels exhibit excellent mechanical and pitting corrosion resistance properties.

Jan 1, 2009

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By AIME AIME

THE John Fritz Medal Board of Award, at its annual meeting on Jan. 21, 1921, awarded its gold medal and diploma to Sir Robert Hadfield for the invention of manganese steel. On June 1, announcement was made that the Board of Award had awarded its gold medal and diploma to Charles Prosper Eughe Schneider for "achievement in metallurgy of iron and steel; for development of ordnance, especially the 75-mm. gun, and for notable patriotic contribution ' to the winning of the war." The award to Sir Robert Hadfield is for the year 1921; the award to Mr. Schneider is for 1922. The latter was made at this time in order that the medal might be presented by the group of American engineers now visiting England and France.*

Jan 1, 1921

The week of Sept. 22, will be a week of convocation of societies in Chicago with the exposition of Chemical industries. The American. Institute of Mining and Metallurgical Engineers will occupy the stage for most of the week, American Ceramic Society meets on Wednesday, the American Electrochemical Society on Thursday, Friday, and Saturday, and the Technical Association of Pulp and Paper Industry from Wednesday to Saturday. There will also be a symposium upon Safety in the Plant and Mine under the chairmanship of M. L. Leopold, Safety Engineer of the U. S. Bureau of Mines, and in the evening after this sleeting-which will occupy an entire afternoon-there will be shown a series of motion pictures of safety work in plant, field-and mine. The motion picture program will consist almost entirely of films now being made. Even in motion pictures, the Exposition is outstanding as the place of introduction to the public of the newest and most recent developments. Each improvement of the projectoscope in motion-picture projection has been reserved for first public demonstration at the Exposition. Mention cannot be made of the new exhibits that are engaged for the Exposition, other than to say that the electric furnace will be in operation. These will give, probably for the first time, men of science an opportunity to see and compare the various designs and judge them for the various work to which they are applicable.

Jan 8, 1919

By F. M. Ramadhan, M. R. Pratama

Monitoring open-pit mine road conditions has become very critical nowadays. There are several benefits to in conducting research on this field such as opportunity to improve truck’s speed which directly influences truck’s productivity. This research aims to provide a semi real-time, and sensors-based automatic road damage detector that predicts the road quality through road damage exact location tracing, road damages auto-classification, and real-time instruction in the form of work order format to mining road maintenance, and repair authorities through mobile apps and maintenance unit’s in-cabin display. It will also provide the maintenance/repair activity performance evaluation via integrated dashboards. The artificial neural network algorithm is applied during the process of data training regarding classifying road damages and severities which resulted in a valid model. The road damage classification model has a precision level of 80.5% in predicting whether the road is damaged or not. Using this approach, we are expecting to visualise a road quality map of all active roads on mine site.

Sep 1, 2021

By C. F. Quest

THE steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more compre-hensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collec-tion of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combina-tion of tables and an equation. The latter include work by Campbell2,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Tensile strength = 41500 + 770C + 1000P + yMn [1] y was a variable depending on the carbon and manganese content of the steel and was listed in tables, Webster investigated acid Bessemer steel and developed the equation Tensile strength = 38000 + 800C + xP + yMn [2]

Jan 1, 1940