Search Documents

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By A Turns

In a survey conducted by symplexi with underground miners in Australia; 78 per cent of participants believed that ‘safety’ is all about people. If ‘safety’ is about people, then is the mining industry focusing on the wrong thing? It would be fair to say that the mining industry is heavily systems focused. Companies develop a safety management system and use this to show regulators that they comply with legislation – however, that is only half of the picture.

May 5, 2022

By John D. Lupton

This paper will discuss the benefits and advantages of using 3D survey data in stope analysis. Obtaining detailed 3D survey data of underground mine progress and production is a challenge. It is almost impossible to ?see? around corners, underneath overhangs, or deep into dark, dusty, humid underground voids. Thus, valuable ore can remain permanently encased in backfill. Without the benefit of 3D survey data, underground mines have the difficult task of meeting grade quotas without the benefit of knowing exactly what has been mined. Lack of this data usually results in unfavorable month end Reconciliation factors, where grades must be adjusted to match grades assessed by the Mill.

Apr 1, 2005

We all live in professional silos û comfort zones, where we talk to like-minded people with the same training, experience and view of the world. We note in passing the existence of other disciplines, but they are tolerated rather than embraced. To the geologist, the metallurgist is a mad scientist conjuring gold out of some foul solution about which the less said the better. To the metallurgist, the geologist is a bearded, self-appointed sage who guesses what is under our feet by sniffing the air, and drives a Land Rover badly. As to the view of mining engineers held by both geologists and metallurgists, this is best left to the imagination. And of course we are all confused by the term æmetallurgistÆ. I am called a metallurgist though my skills are in mineral processing not metal processing, but I canÆt be called a mineralogist because that definition is already taken. *Please note that this is available as an extended abstract only*

Jan 1, 2005

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By . Menad Gaballah I

Three samples of solid wastes generated by the non ferrous metallurgy were characterized. These residues contain up to 42 % of valuable metal compounds ( Cu, Pb and Zn ) and 23 %of toxic compounds t As, Hg, Cd and Se ). These sample were subjected to thermal treatments between 200 DC and 800 °C in controlled oxidizing. reducing and chlorinating atmospheres. Up to 99 % of As, Cd, Hg and Se were eliminated from these industrial wastes. Cu, Pb, and Zn compounds were concentrated in the treatments' residues of these samples. A Global Decontamination Factor' GDF ' was defined to measure the efficiency of the elimination of toxic elements and the recovery of valuable elements for a specific sample submitted to a given treatment. It seems that the thermal treatment in a reducing atmosphere was the most efficient in decontaminating these solids and the concentration of valuable elements. a.

Jan 1, 1995

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

By Raja V. Ramani, Robert L. Frantz

"The House/Senate Joint Conference Committee has instructed the Bureau of Mines to have the Advisory Committee on Mining and Mineral Resources Research review on an annual and simultaneous basis each generic mineral technology research center (GMTC). In order to accomplish that review promptly and uniformly, committee members have revised and approved an in-depth questionnaire. That document formed the basis of their review. The information provided by that questionnaire was an important factor in their recommendations concerning the future direction of the program; a presentation was made at the last National Plan Update.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now will help guide it into the future. It is felt that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members.Each aspect of the questionnaire has been examined, answered in detail, and documented throughly. With the completed questionnaire as a guide, this volume examines the research program, Center personnel presently active on GMTC projects, number of graduate degrees granted with GMTC support, GMTC publications, degree of individual interaction, technology transfer, the reference center, GMTC equipment and facilities, and any envisioned plans for future research. It is hoped that this volume will serve as a review of the years 1984-1988, the first four years of the Center's operation."

Aug 31, 1989

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By C. Norman Bowers, Blaine B. Wescott

Marked improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pumping conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By R. H. Richards

In October, 1891,I read a paper before the Institute on a "A HandTelescope for Stadia-Work" (Bans., xx., 732), and promised to report at an early date some results showing the degree of accuracy attained with the instrument. I am now able to report on these results and also on certain improvements that I have made in the target since the first paper was read. I may say that I prefer the title, "Prismatic Stadia-Telescope," to that used in my earlier paper, for while the instrument can be used with perfect satisfaction for short sights up to, say, 300 to 600 feet when held in the hand, it is impossible to read milch longer distances without the use of a tripod, as a steady support for the instrument. Results are here given upon four combinations of prism and telescope. No. 1. A telescope made by Alvan Clark & Sons, 3-inch objective, 28 inches focal length, magnifying 60 diameters, the prism covering half the objective: Feet measured Reading of Distance reduced Reeding of rod pro by tape. the rod. to feet. portional to 100 ft. 127.66 1.1825 100 .92629 211.35 1.9585 100 .92666 326.59 3.0265 100 .92669 484.88 4.4925 100 ,92652 606.91 5.6225 100 .92641 Average,,92651 The value of this prism therefore is .92651 feet on the rod for 100 feet of distance, or 1 foot on the rod corresponds to 107.931 feet of distance. No. 2. A Bardou telescope having a 1-inch objective, magnifying 20 diameters, and a prism covering half the objective:

Jan 1, 1893

By N. W. Wickersham, Ward B. Blodget, Roberts R. Boyd

The year 1926 has seen few radical changes or developments in methods of drilling and handling oil wells, but it has been a year of steady progress and development in deep drilling and production methods. Probably the outstanding development of the year was recognition by the directors of the American Petroleum Institute of the importance of natural gas in the production of oil, and the Institute directors' resolutions in December, 1926, regarding regulation of gas production with oil by state legislation. This matter is extremely important and will receive the attention of the industry in 1927. Advances in Drilling Equipment The history of the progress of deep well drilling is the solution of problems as they have confronted the operator. As the prospects for deeper production have become apparent, methods of penetrating the earth to greater depths have been devised. Rotary Equipment Improvements in the construction and in the methods of operation of rotary drilling equipment have practically caused elimination of cable tools in California for all but shallow work. The rotary drill, from 1910 when it began to be a practical factor in California, has been making steady advances, first displacing cable tools for drilling to the oil sands in proved fields and later displacing the cable-tool outfit entirely. With the perfection of machinery for taking core samples of the formation penetrated, the rotary drill has become generally used for wildcat work, continuous coring being practiced when desirable. Deep Holes The use of the rotary drill has made commercially feasible the opening of oil fields at greater depths than was considered possible with cable tools. Heavier equipment has been promptly supplied as occasion has

Jan 1, 1927

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By NA NA

Background information on Exchem Mining and Construction and its products.

Jan 7, 1997

By G. C. Gullo, H. Wabusseg, P. J. Uggowitzer, H. Kaufmann

"The basic concept of New Rheocasting (NRC) is described and the application of wrought alloys with this process is discussed. Practical experiments with the aluminium alloy AIMgSi I are explained. For this alloy the proper NRC - casting temperature was determined by using Thermo Cale - computer software and DT A and the essential processing conditions are shown. In the experiments the melt was taken from an aluminium holding furnace and cast into NRC steel cups. After controlled cooling the resulting slurries were cast into a 4-step die on an UBE HVSC 350 Squeeze Casting machine. The characteristic microstructural values such as grain size and shape factor were measured and compared with classical casting alloys. The influence of the wall thickness of the step part (6 mm, 10 mm and 14 mm) on the microstructure is described. Tensile properties in different heat treatment states are compared with characteristic prope1ties of the same alloys in forged condition. The ew Rheocasting - process CNRC)The NRC process is a recently developed new semi-solid processing method which allows the production of pore-free, pressure tight components.In the NRC process a fu lly liquid, but only slightly superheated melt is taken from a holding furnace and poured into specially designed steel crucibles, which are placed on a carousel next to the Vertical Squeeze Casting machine. In this ,NULL,slurry maker'· globul ar a-Al grains grow, following forced homogeneous nucleation at the cup wall [ 1, 2]. In the few minutes during which the melt is cooled to sem i-so lid processing temperature, a stable ske leton of a-Al phase forms. The resulting slug keeps a cylindrical shape during its slide into the sleeve of the Vertical Squeeze Casting machine, where it is cast into shape."

Jan 1, 2000

By Roland Hoet

Mine operators, conveyor system designers, consultants, and manufacturers have had opportunities over the past decade to utilize various actively controlled technologies to drive complex underground conveyor systems. These technologies included several electrical drive solutions, mechanical drive solutions, and hydromechanical (fluid coupling) drive solutions. All of these technologies have their inherent advantages and disadvantages, and only after several years of operation can mine operators fairly evaluate the overall benefits (short term performance and cost vs. longer term operational and maintenance costs) of any particular drive. Far too often in today's world, decisions for new equipment are made with inadequate regard to issues concerning serviceability and maintainability. Many of the newer electrical technologies (primarily AC variable speed drives) which have been used in recent years were selected based on the perceived desirable benefit from variable speed operation. This technology, however, which differs sign8cantly between various manufacturers, is in a constant state of evolution which puts into question the manufacturers' ability for long-term product support. In addition, various forms of this technology have also generated some undesirable operational issues, including reduced motor life, harmonics for the power system, and mine communications problems. This technology is also extremely current-limited, which results in problems handling overload conditions, a frequent occurrence often resulting from a decline in the coal recovery rate (conveying more rock than coal). The fluid coupling, however, is based on a technology which has been used successfully in underground conveyor applications for decades. Although the base hydrodynamic technology is well proven and has inherently beneficial characteristics on conveyor applications, Voith has continuously improved on this technology to meet the increasing demands of today's challenging conveyor haulage systems. Recognizing a need in the market for a reliable, actively controlled drive system, Voith Turbo began development in 1996 of a new, actively controlled coupling which was targeted specifically for the higher powered, complex underground conveyors. Voith introduced the new TPKL Fill Controlled coupling product to the market in 1997, and the first two applications for this new technology were on multiple drive mpper booster applications on longwall panel conveyors. Since the successful startup of these two conveyor systems in 1998, Voith has supplied over 200 TPKL couplings to the mining industry worldwide, with over 150 in US coal mining applications alone. This paper will provide an overview of the TPKL's capabilities, performance, and reliability based on the TPKL's impressive installation base and operational history.

Jan 1, 2004

By Richard L. Sayrs

"The Stiner zinc prospect near the north boundary of Union Tennessee, and the Bunch Hollow property 5 miles northeast in Claiborne County, Tennessee, were diamond-drilled by the Bureau of Mines during the period .September 1, 1944, to February 22, 1945. Seventeen holes totaling 5,687 feet were completed, 13 of which, totaling, 5.083 feet, were on the Stiner property and the remainder, totaling 604 feet, at Bunch Hollow.The Stiner prospect is about 1 mile east of the old workings known as ""New Prospect"" or ""Lead Mine Bend."" The Federal Geological Survey made a study' of the area early in 1944. The prospect was first visited in August 1944 by Bureau of' Mines engineers3/ accompanied by members of the Federal Geological Survey.4/ The locality is reached by traveling State Road 33 north-about 9 miles from Maynardsville, Tenn., thence northwest about 7 miles by an improved county road that leads to the mine (fig. 1). The tract comprises an area of about 181 acres held by G. S. Stiner of Sharps Chapel, Tenn.; it is now under option to the Universal-Exploration Co. of Jefferson City, Tenn.The Bunch Hollow property, about 5 miles northeast of the Stiller prospect, was also studied by the Federal Geological Survey previous to being;Visited by Bureau of Mines engineers in August 1944. It is reached by traveling north from Maynardsville, Tenn., on State Road 33 about 13 miles, thence northwest by county road 6 miles to the property (fig. 1). The last 3 miles of the county road are in poor repair but are passable during the entire year. The property comprises an area of approximately 300 acres and is held by the imperial Mining Co., Pressman's Home, Tenn.Few reliable data are available as to the history of the Stiner prospects themselves. However, the New Prospect mine, 1 mile west, has had a colorful past, This mine was opened in 1883 and was worked intermittently until 1918, by which time more than 65,000 tons of concentrates had been shipped. No further work was done until 1942, when the mine pillars were robbed and 1,900 tons of ore averaging 25 percent zinc was shipped to the New Jersey Zinc Co., Austinville, Va."

Apr 1, 1946

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023