Search Documents

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By L. Tavares

The significant capital and operating expenditure of size reduction operations have maintained comminution on the spotlight of mineral processing research during the last century and, more recently, the concerns about the impact of these operations on the sustainability of the minerals industry, will remain to do so in the 21st century. One of the most popular approaches that have been used to deal with these challenges is the application of simulation both to reduce the uncertainty in the design and improve the operation of size reduction operations. From the initially purely empirical approaches, including the energy size reduction ?laws? and the phenomenological approaches, of which the traditional population balance model is, arguably, the best example, comminution modeling now reached a point in which more fundamental and mechanistic models are sought. The paper analyzes some of the advances that now make multiscale modeling of comminution processes realizable. On the microscale, greater understanding of the phenomena involved in fracture and fragmentation of single particles under different stressing conditions now exists. Particle breakage testing methods are currently used in a routine basis by industry and good quantitative descriptions of different breakage mechanisms are now available, although research is still required to develop appropriate models for a couple of them. On the macroscale phenomena, the discrete element method (DEM) has been successfully used not only to provide insights but also quantitative information on the transfer of mechanical energy from the machine to the grinding media in mills and to particles in crushers, while smoothed particle hydrodynamics (SPH) and computational fluid dynamics (CFD) to describe fluid flow. The paper also analyzes the importance of modeling mesoscale phenomena in size reduction, which is the interaction of particles forming assemblies or beds of particles, demonstrating some of the areas requiring further attention. Examples of application of the multiscale modeling approach to the inadvertent comminution of ore lumps during handling, to the comminution in vertical impact crushers and tumbling mills are demonstrated. Keywords: comminution modeling, DEM, SPH, CFD, multiscale modeling approach

Sep 1, 2012

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

G. McMEANS*—This paper is a very good demonstration of the use of a new tool for the solution of industrial problems of a physical nature. To have solved this problem without the use of radioactive tracers would have required a far greater amount of investigation and work. The authors have described their work in such detail and in such a manner as to suggest the possibilities of the use of such tracer studies in the solution of many perplexing problems of industry. R. E. BREWER †—The authors are to be congratulated on this very excellent paper, which describes the results obtained by utilizing radioactive tracers in investigating the complicated reactions in the coking process. The paper has especial merit because the study was made under typical operating conditions in a commercial coke oven. Considering all the difficulties involved, the results obtained are excellent. My brief comments will relate primarily to the method used for determining the sulphur in the gas and to the value of the data obtained in stimulating further research. In discussing their results, the authors state (p. 17) that "Of the total sulphur charged to the oven in the coal 95 pct was accounted for in the coke and gas. Most of the sulphur unaccounted for is believed to have been lost in the gas, since the gas sampling system removed all the H2S but probably only part of the organic sulphur compounds present in the gas. Although sulphur in the acid-insoluble tar residue in the gas scrubbing bottles was determined and added to the total sulphur determination of each sample, it is doubtful whether an aliquot portion of tar for each sample was obtained." The reviewer believes that the authors might have obtained a better sulphur balance had they used an improved procedure for determining sulphur in the gas. The absorption train should have included a trap to remove the tar and am-moniacal liquor and a wash bottle containing 5 pct sulphuric acid to remove ammonia in the coke-oven gas before it entered the gas scrubbing bottles containing the ammoniacal cadmium chloride solution. Sulphur in the tar and

Jan 1, 1950

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO = Zn(g) + CO2 This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction does not occur at an appreciable rate, as is expected from thennodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide coneentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

By J. D. Alexander, W. L. Martin, J. N. Dew

This paper presents data obtained using a flood-pot technique to determine the fuel available and the corresponding theoretical air requirements for in situ combustion of crude oils. Since the technique is relatively quick and easy, it is a practical and convenient tool for evaluating reservoirs as fireflood prospects. It is also a research tool which facilitates systematic study of the variables affecting fuel availability and corresponding air requirements. The understanding of these variables is of prime importance to those concerned with the technical and economic development of in situ combustion as an oil-recovery process. The experimental results show conclusively that the fuel available for in situ combustion is not a constant but, rather, varies with crude-oil characteristics, porous-medium type, oil saturation, air flux and time-temperature relationships. Thus, the fuel availability for specified field applications should be determined using actual reservoir crude and core material and the process conditions expected during in situ combustion in the reservoir. INTRODUCTION In situ combustion is a thermal process for recovering crude oil from reservoirs. The thermal energy released during the combustion of a small amount of the oil in place aids in the displacement of the remaining oil. Numerous articles have been published describing the in situ combustion process giving detailed results of laboratory and field experiments.10 In order to engineer an in situ combustion project, a number of important factors must be considered and determined. These factors include: (1) the amount of fuel consumed per unit of reservoir volume swept by the combustion zone, (2) the composition of the fuel consumed, (3) the amount of air required to consume this fuel, (4) the portion of the reservoir swept by the combustion zone, (5) the appropriate air-injection rates and pressures, (6) the amount of oil that will be recovered, (7) the rate of oil production and (8) the operating costs. Nelson and McNiell1 recently have described a procedure which utilizes laboratory combustion-tube data as a basis for the calculation of some of these design factors. Various authors have attempted to describe the in situ combustion process mathematically, and considerable progress has been made. Analytical solutions to the problem of heat transfer from a moving combustion front have been obtained for linear and radial systems."-' All of the published results involve the assumptions that: (1) fuel concentration is constant throughout the reservoir, or that fuel concentration is inversely proportional to the velocity of the front for a given rate of oxygen consumption; and (2) the fuel reacts instantaneously with injected oxygen, while liberating a constant amount of heat per unit weight of fuel at all temperatures. It seems both desirable and reasonable to test the validity of these assumptions experimentally. This paper presents laboratory data which were obtained by means of a "fire flood-pot" method for determining fuel availability and composition, and the corresponding theoretical air requirements for in situ combustion of crude oils under variable conditions. The mechanics of the method are similar to a conventional tube-run experiment.' The important differences involve the size of the reservoir model used and the method for providing the experimental environment. The new method subjects conventionally-sized core samples or unconsolidated sands to a programmed environmental sequence similar to that experienced by a similar volume of rock during the approach and passage of a combustion front in a long tube or in an oil reservoir undergoing in situ combustion. Restored-state samples can also be used. The small samples and relatively simple techniques involved allow an experiment to be set up, run and calculated in about three 8-hour days. This is a considerable improvement over long-combustion-tube techniques which can require several days to run and several more work days to set up and calculate. All the runs presented were run at 40-psig injection pressure. Pressure was not considered as a variable for these experiments, since we previously had found that it had only a small effect on fuel availability up to 600 psig.APPARATUS AND MATERIALS APPARATUS The fire flood-pot apparatus consists of a consolidated

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

By Carla Lupi

NiMH sealed cells (portable cells) are today widely used in all consumer applications replacing primary alkaline batteries: wireless mobile communication, portable computers and camcorders, are the largest application segments. The Italian market. of NiMH cells is steadily growing, following the impressive penetration rate of the cellular phones. The organization of a national collecting system and correct recycling process are the key factors to prevent environmental impact associated to these wastes, while the metal values recovery can improve the feasibility of the recycling process The University of Rome, Texeco Engineering S.d, and MO.SMO.DE. S.a.s. have developed a combination of mechanical and hydrometallurgical processing to recover Nickel, and Cobalt salable products and rare earths intermediate products. A new plant located in South Italy, designed after this technology, is able to recycle waste Ni-MH batteries collected in the Italian territory, together with other industrial and portable batteries based on different chemistries. The process is able to treat both individual cells and plastic power packs and includes as basic steps an original crushing and elutriation treatment to separate plastic, metallics, and active mass components that are subsequently treated by a hydrometallurgical process to recover Ni, Co, and RE. The hydro metallurgical main steps are: acidic leaching, RE separation, multistage precipitation of Ni, Co and Fe and final solvent extraction on dissolved Ni and Co salts. For each operation the operative condition have been determined.

Jan 1, 2000

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By L. Bloom

"Man-Made Parameters" refers to the importance of selecting appropriate analytical procedures to acquire useful chemical data. The correct procedures are particularly critical at the sample preparation stage where decisions concerning pulverizing equipment, sample size, contamination and dissolution will impact on the final results independent of the instrumental method of analysis. Several experiments were designed to quantify the impact of these approaches.

Jan 1, 1993

By T Kilpatrick

Managing heat stress on Australian mine sites is a complex and enduring challenge due to the combined and variable contribution of environmental conditions, physical activities, and protective equipment. Inappropriately managed, heat stress can place significant physical strain on workers, leading to serious and chronic health issues. Additionally, excessive heat stress can dramatically reduce productivity, with 30 per cent of workers reporting a loss of productivity due to occupational heat strain. In Australia, due to increased absenteeism and reduced work performance, heat strain is estimated to have an annual economic burden of over $8 billion.

May 5, 2022

By L. Muñoz, L. Steffen, W. Vilas

The emission of particulate material is one of the several parameters related to environmental control in mining operations near communities. Blasting is an event that generates and leaves a large amount of dust in suspension, which can cause discomfort to communities, generating complaints that can compromise the operational continuity of the mine. The proper management of these environmental impacts is a key factor to ensure a good relationship with the neighborhoods, making a responsible mining in harmony with the environment, giving sustainability to the mining business in the medium and long term. The main goal of this work is to present different techniques and technologies applied in a large-scale open pit mine in Brazil, with operations close to a community, to minimize the emissions of particulate material into the atmosphere. For this, different technical solutions were implemented. First, a non-conventional blasting technique was introduced that incorporates special charging and timing configurations, generating a first upper layer that serves as a blanket to contain a second, higher-energy lower layer. An optimal stemming was also defined in order to minimize ejections and maximize cratering, using the scaled depth of burial theory as well as video and fragmentation analysis. In addition, changes were made in the timing between decks (to guarantee a minimum time between layers) and between holes (changing the initiation point opposite to the free face). Finally, additional measures such as humidification of the bench, use of a wind vane to identify wind direction and the construction of a physical barrier between the mine and the community were implemented as additional mitigation measures. By applying the above techniques together, in some specific zones of the mine, it was possible to considerably reduce the ejections generated by blasting versus conventional blasting without the above measures, which was demonstrated in the field with dual blasts trials. Additionally, it was possible to achieve a vibration reduction in the community of ~30%. This work demonstrates how, by applying these technical solutions, it was possible to minimize the dust and vibrations generated by blasting allowing this operation to do sustainable mining

Jan 1, 2024

By Francis F. Pitard

North America had an Important role in the early development of sampling theories. Unfortunately many progressive ideas were soon frozen into a series of guidelines based on the philosophy that "honest sampling only requires good judgment and practical experience". Such a philosophy appeared to be good enough In the early age of the mining Industry; however, it became quickly necessary to find new approaches. During the last thirty years, Pierre Gy's sampling theory provided tremendous breakthrough in the comprehension of this new science, nevertheless went unnoticed in North America. Sampling always generates complex problems and as the philosopher and mathematician Descartes suggested: "A complex problem can often be dissociated Into a series of several simpler problems, only then you try to solve those one by one". The only way to solve sampling problems is to consider each component of the overall sampling error: components of a continuous model such as long-range quality fluctuations, periodic quality fluctuations, weighting fluctuations; components of a discrete model such as materialization errors, delimitations errors, extraction errors, fundamental errors, grouping errors, and segregation errors. PAST AND CURRENT PRACTICES Many sampling methodologies have been developed, improved, and standardized during the first half of this century. Accordingly, sampling equipment has been proposed, selected, and used by standards committees. Today, there is a tremendous variety of sampling methodologies and corresponding tools offered to anyone with limited experience in sampling and it is very easy for a chemist, metallurgist, geologist or miner to spend considerable money in equipment transgressing the most basic rules of sampling correctness. Sampling stations that never worked properly in modern plants often cause engineers to abandon them and return to a primitive form of grab sampling.

Jan 1, 1986

By Francis A. Thomson

IN reviewing mineral industry education a year ago, occasion was taken to congratulate the Institute in general and to felicitate the Education Di- vision in particular on "the most gratifying growth which is taking place in Institute consciousness in regard to its responsibility for the recruitment and adequate training of student personnel and for the successful bridging of the difficult gap between graduation and achievement of professional status." Continuation of this growth of interest throughout 1939 is a recognition of the validity of the splendid statement of George Otis Smith that the mining students of today are the ore reserve of the Institute for the future. In this connection one recalls the equally apt expression of another distinguished geologist, George M. Fowler, who, speaking of exploration for ore deposits, says, "The place to look for elephants is where elephants have been found."

Jan 1, 1940

By S. N. Monteiro, J. Alexandre, L. G. Pedroti, D. P. Santos, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

The glass cutting industry is responsible for generating large quantities of waste, during the stages of cutting and polishing. The disposal of this material generates a cost to the company, thus looking for ways to repackage it, so there is the possibility of incorporating it into the adhesive mortar. The objective of this work is the characterization of waste and assessment of the properties of these mortars, fresh, and check the possibility of their use. As for the characterization, were carried out particle size testing, density and pozzolanic activity, for the fresh state were performed tests of air content, water retention consistency and entrained particular index. Were incorporated 0,10, 15 and 20% of the amount of sand. The results showed that the material on display ha spotential for use in adhesive mortar, with values within the limits stipulated by Brazilian standards.

Mar 1, 2017