Search Documents

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By ALFRED T. BARR

In certain areas of the New Cornelia pit, considerable secondary blasting is necessary to reduce oversized boulders, formed from primary blasting, to pieces which will pass the 41/2-cu yd dippers on the shovels. Some of the boulders are 'dobied, but when time permits they are blockholed and blasted. In most instances one hole drilled to a depth of 2 to 3 ft and blasted with 1/3 to 1/2 of a stick of powder will break a boulder satisfactorily. Blockholing is normally done by using a jackhammer of the 55-lb class, 1-in. round drill steel, and detachable steel bits, 2-in. gauge when new. A bit change is usually made after the completion of each hole. The use of light drilling equipment in blockholing is desirable, both from the standpoint of safety and ease of doing the work, and when it was seen there was a possibility of using a lighter jackhammer through the use of tungsten-carbide bits and at the same time get at least the same drilling efficiency as with the standard equipment, it was decided to test tungsten-carbide bits. The claims for long life of the bits and footage drilled before resharpening gave hopes of eliminating much of the delay time in changing bits which is unavoidable with the use of steel bits. and thus gain in actual drilling time.

Jan 1, 1949

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By Philip U. Santacroce, James H. Meinholz

INTRODUCTION The Milwaukee Metropolitan Sewerage District (MMSD), is a special purpose sub-regional agency that provides collection and treatment services for sanitary wastewater for an area of 420 square miles (1088 km2) in 27 municipalities in the Milwaukee, Wisconsin metropolitan area. During its almost 75 years of existence, it has constructed 464 km of intercepting sewers, the majority in tunnel, and two sub-regional secondary wastewater treatment plants. The present program, the $1.7 billion Milwaukee Water Pollution Abatement Program, was started in 1977 and developed from ongoing internal planning, the Federal Clean Water Act and court judgments. Elements of the Program include improvement and expansion of the two treatment plants; rehabilitation of older in-place sewers; building new interceptors and relief sewers and providing capacity for high volume storage in approximately 32 km of deep, large diameter rock tunnels; reducing combined sewer overflow; and disposal/utilization of the solids that remain after the treatment process. The construction phase of the Program accounts for $1,105,900,000 within 335 separate construction contracts, 211 let to date, and covers a span of 15 years, starting in 1979 and running through 1994. Conveyance System construction cost is estimated to be $650,000,000 or about 60 percent of the total. Through December 1986, in terms of dollars, the total construction program is about 38 percent complete with Conveyance at 34 percent complete.

Jan 1, 1987

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

Discussion of the paper of H! M. CHANCE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1461 to 1466. R. V. Norris, Wilkes-Barre, Pa.-In his resume of coal-taxation methods Mr. Chance has apparently confined his investigation to bituminous coal, so a summary of the anthracite situation as to coal assessment should be of interest. The anthracite region of Pennsylvania in its 484 square miles of measures lies in the counties of Wayne, Lackawanna, Luzerne, Carbon, Schuylkill, Northumberland, and Dauphin, and in each of these different methods of assessment have been adopted. The assessments for taxation in Pennsylvania are made under Acts of the Legislatures of 1841 and 1842, under which the assessors are re¬quired to "assess rate and value every subject of taxation according to the actual value thereof, and at such rates and prices as the same would bring at a bona fide sale after due notice." Under this general law coal land has been assessed as such, but up to about 25 years ago the coal was assessed at rates so low as to be unimportant, though the rates in each township and municipality, even in the same county, showed no agreement or ascertainable basis. In the late '80s, the need for greater revenue drew attention to the possibilities of collecting much larger taxes from the coal lands and, spurred by public demand, the assessing authorities in some counties undertook a reassessment of coal. The method pursued was to demand from each owner a statement of the area and average remaining thickness of coal on his lands. On this return, made in some cases under oath, an assessment based on foot-acreage was levied, with a resulting great increase in valuation, but the valuation per foot-acre was low and no serious objection was made. This assessment with occasional increases of rate remained in force until 1907, when, in the triennial assessment of that year, a complete revision of the valuation was again attempted, engineers were employed by the counties to check the accuracy of the returns from the owners, and, based on the foot-acreage thus obtained, an enormous increase, to $65 per foot-acre, was made in the valuation. This assessment was resisted in the courts by appeals resulting in very extensive litigation, and a final determination of the validity of the 1907 and all subsequent assessments has not yet been obtained. In the first appeals tried the rate calculated on a foot-acre valuation was reduced by the Luzerne County court to about $45, while the. Lackawanna County courts reduced a larger rate to $67. The county authorities were, how-

Jan 4, 1915

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By X. Cui, H. Ding, J. Wen, Q. Gu

This study is a continuation of previous work designed to further explore the mechanism of the bioleaching of sulfide concentrate at neutral pH by heterotrophic bacteria Bacillus megaterium QM B1551. The concentrate contained 13.2 percent nickel (Ni) and 0.2 percent cobalt (Co), which presented primarily as pentlandite and pyrrhotite. Contact and noncontact bioleaching experiments were conducted with finely ground ore at an initial pH of 6, resulting in 44.7 percent of Ni and 38.2 percent of Co leached in the contact-bioleaching treatment. Oxidation experiments of sulfur, thiosulfate (S2O32−) and ferrous ions (Fe2+) by cell membrane were performed to verify whether sulfur transferase, thiosulfate quinone reductase and enzyme cytochrome B558 on the surface of the bacteria could be expressed to oxidize the sulfide. The results show that thiosulfate quinone reductase and cytochrome B558 could be expressed to oxidize S2O32− and Fe2+ to SO42− and Fe3+, respectively.

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By A. C. Burrow, R. P. King

A dynamic model that predicts the variation of carbon content with time in the argon-oxygen decarburization (AOD) process has been developed. The model recognizes three distinct zones in the AOD vessel: the tuyere region in which the blown oxygen reacts very rapidly with the metal components in the molten alloy; a region in which bubbles of inert gas and oxide drop lets rise through the molten alloy; and a zone in which the slag layer can interact with the molten alloy. The process is dynamically controlled by the rate at which dissolved oxygen, produced on the surface of rising oxide droplets, and dissolved carbon diffuse through the molten alloy to react at the surface of the rising bubbles. The rate at which carbon and oxygen react on the bubble surface is assumed to be intrinsically very fast. Predicted decarburization rates compare reasonably well with rates measured in the AOD vessel at Middleburg Steel and Alloys. The model has been developed primarily to allow development of a time-optimal blowing stategy for the AOD vessel.

Jan 1, 1990

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By Shosei Serata, Bruce Gardner

A system of three new field instruments has been developed to measure, in situ, the three basic classes of geomechanical parameters: material properties, stress state, and creep deformation. The significance of this development is that it represents a successful adaptation of recent computer technology to underground rock mechanics work, opening up new possibilities in underground mining methods. The system was developed to meet the application requirements of the stress control method of mining, a method which is based on the actual geomechanical conditions of the underground, rather than upon conventional linear-elastic, idealizations of ground conditions. These instruments enable in situ measurement not only of elastic, but also post-elastic, yielding, and failure conditions of geological materials, establishing the stress control method on a truly scientific foundation. In order to evaluate the present status of this field instrumentation system, case examples of underground mine openings designed with the stress control method are reviewed and analyzed, in terms of the effectiveness of the three instruments for informing and guiding the site-specific application of stress control design.

Jan 1, 1984

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980