Search Documents

By Yuanbo Zhang, Zhixiong You, Li Qin, Guanghui Li, Tao Jiang

Low-grade manganese oxide ore is generally characterized by high iron content. In this work, sulfidation roasting of an iron-rich manganese oxide ore with elemental sulfur was characterized. The experimental results indicated that manganese dioxide can be selectively reduced over iron oxide by using elemental sulfur. The manganese phases in roasted product included low-valence manganese oxide, manganese sulfide and manganese sulfate, while those of iron mainly depended on the sulfur addition. Iron oxide would only be reduced or sulfidized at larger sulfur additions. The effect of roasting temperature and S/Mn mole ratio on the phase transformations was also investigated; extractions of Mn/Fe by sulfuric acid were evaluated. An extraction of Mn greater than 95% was obtained while that of Fe was controlled less than 10% under the optimal conditions.

Jan 1, 2016

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The development of reliable and accurate solution sampling systems plus on-line atomic absorption spectrophotometers and voltammetric analysers at Pasminco Metals - EZ's (PMEZ) zinc refinery at Hobart, Tasmania, has led to extensive implementation of On-Stream Analysis (OSA) throughout the hydrometallurgical circuit. These systems complement industrial autotitrator and colorimetric analysers and with the comprehensive use of a powerful integrated Distributed Control System (DCS), provide extensive monitoring and control of all the important in solution' parameters for the plant. Samples can be left unaltered, or filtered or settled, to remove solids. They are then precision diluted and pneumatically transported to analyser shelters, where they are analysed for zinc, acid, copper, cadmium, lead, antimony, cobalt, nickel, mercury and ferrous, ferric and/or total iron. The range of analyses depends on the sample itself. The results are used for feed forward and/or feedback control of reagents where possible, or simple trend monitoring and out-of-specification alarming when closed loop control is not practical. The overall system reliability and accuracy is such that many daily composite plant samples are no longer analysed off-line. Operator sampling has also been reduced, and in two places, autotitrators with automatic sample pre-treatment have been installed for preparing and analysing samples collected by operators.

Jan 1, 1993

By Charles L. Kimbell

The year 1988 for the minerals indus¬try was one of favorable worldwide economic conditions for continued, rationally constrained growth. There was continued improvement in relations between market economy nations and the Soviet Union and China. The "shooting war" between Iran and Iraq ended. Soviet troops withdrew from Afghanistan. And conditions were generally favorable for economic growth in developed market economy countries. These favorable conditions were darkened only somewhat by the continuing foreign debt crises discernible in some major mineral producing developing market economy countries. However, there were situations developing that became major headlines in the late spring - situations that may have pronounced effects in 1989. The most significant event is the muddled situation in China. There is a good chance of worsening international relations and consequent restraint of development projects that could prove beneficial to China and her international partners. Of only slightly lesser evident significance was the death of Ruhollah Khomeini in Iran. This could lead to a variety of paths for the new Iranian leaders. Continued outbreaks of ethnic unrest in the Soviet Union clearly presented problems to the Gorbachev regime. This unrest has raised questions of how far the doctrines of "glasnost" and "peristroika" would be extended, including extensions into the minerals field. Another area of unrest is Panama with its tainted election and the Western Hemisphere's obvious dissatisfaction with the Noreiga regime. While not a direct threat to any major mineral industry enterprise, the political situation certainly presents a potential threat to the Panama Canal. That threat would have considerable impact on world

Jan 1, 1989

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By R. M. Santmyers

Thorium and cerium are two of the group of elements known as "rare earth metals," and are obtained from the mineral monazite. Previous to the employment of thorium and cerium in incandescent gas mantles these elements were nothing more than laboratory curiosities, as the rest of the rare-earth metals are to-day. The most important salts of these rare earths are the nitrates. In the manufacture of gas mantles, thorium nitrate is the principal ingredient and forms prom 92 to 99 per cent of the impregnating material; the other 1 or 2 per cent is largely cerium nitrate and is quite as necessary, for without it there would be little luminosity to the mantle when in use. When the mantle is "burned off," the nitrates are changed to oxides. The monazite used as a source of thoria contains from 6 to 9 per cent of thorium oxide (Th02) and 24 to 32 per cent of cerium oxide (Ce203). As only the thoria and a very small hart of the ceria from the monazite could be used in gas-mantle manufacture, for a time the residues consisting mostly of ceria with somewhat smaller quantities of other rare earths found no commercial application. Later, however, they came to be utilized in several ways, the most important being: (1) the manufacture of cored flaming arc carbons, a great, irmprovement over the plain arc carbons used in electric lighting; (2) cerium metal used in the manufacture of pyrophoric or sparking alloys or "flints" for automatic pocket lighters and miners' lamps; and (3) the production of special kinds of optical and art glass.

Jan 1, 1930

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By L. H. Adami, E. G. King

The heats of formation of four sulfides --MnS ( alabandite ) , FeS ( hexagonal pyrrhotite ) , ZnS ( wurtzite ) , and CdS ( greenockite ) -- were determined by hydrochloric acid solution calorimetry . The heats of formation from the metals and rhombic sulfur at 298.15 ° K are , respectively , -51.01 ± 0.19 , -23.81 ± 0.24 , -45.86 ± 0.20 , and -35.70 ± 0.30 kcal /mole . The corresponding free energies of formation were calculated from the heats of formation and the pertinent entropy values .

Jan 1, 1964

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014

By Gordon D. Jarvinen

Polymer Filtration (PF) Is an innovative, selecthle metal removal technology. Chelating, water-soluble polymers are used to selectively bind the desired metal ions and ultrafiltration is used to concentrate the polymer-metal complex producing a permeate with low levels of the targeted metal ion. When applied to the treatment of, Industrial metal-bearing aqueous process streams, the permeate water can often be reused within the process and the metal ions reclaimed. This technology is applicable to many types of industrial aqueous streams with widely varying chemistries. Application of PF to 'aqueous streams from nuclear materials processing and electroplating operations will be described.

Jan 1, 1999

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993