Search Documents

By Raja V. Ramani

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas which have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and many other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1983

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By I D. Hair

A numerical groundwater model was used to predict the nature of interactions between heavy mineral sands mining operations and the groundwater regime at North Stradbroke Island, Southeast Queensland. North Stradbroke Island is formed mainly of massive vegetated Cainozoic aged dune sands. Since the 1950s, a number of operations have mined rutile, zircon and ilmenite on North Stradbroke Island. In such mining operations, a dredge and an associated processing plant are floated in a pond either above or below the prime groundwater table The numerical model was based on the North Stradbroke Island Groundwater Management Model, developed in 2001 by the Department of Natural Resources and Mines (NR&M). This model was constructed using the modular, cell-centred, finite-difference groundwater flow model, MODFLOW, developed by the United States Geological Survey (USGS). The NR&M model was refined to improve model resolution and detail for simulating dredge mine paths. Of particular interest were: water table fluctuations induced by mining for the identification of slope stability risk; the optimisation of sand spear arrays supplying mine make-up water requirements; inflow and outflow rates to the dredge pond for overall mine water balance; and interactions with Eighteen Mile Swamp and water supply bores controlled by the Redland Shire Council (RSC). Depending on the water level in the dredge pond compared with the surrounding groundwater table, water either flows out of the dredge pond into the groundwater regime or from the groundwater system into the dredge pond. The MODFLOW river package (RIV) was utilised for the modelling study. Dredge pond movement was simulated using specialised software developed by Watermark Numerical Computing (WNC) to interpolate pond positions and map the dredge path to the model grid both spatially and temporally. As tailings placement affects the groundwater system through increased recharge, the MODFLOW recharge package (RCH) was utilised to simulate different recharge efficiencies. Long-term model predictions were made for the period from July 2002 to May 2021. Results of the modelling showed that exchanges of flow between mining operations and the groundwater regime could be effectively managed. The study provided valuable information which was used to develop an appropriate mine water management plan.

Jan 1, 2003

By E. Gybbon Spilsbury

THE introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the, difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and there-fore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used maybe, but the chief cause -of the

Jan 1, 1880

By E. Gybbon Spilsbury

The introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and therefore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used may be, but the chief cause of the

Jan 1, 1880

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By Caelli T, Robey M

Most research into planning of open pit mines has been based on evaluation of volume-element block models in terms of their net present value. The major issues revolve around two interdependent problems the optimum ultimate pit and time-based scheduling. Despite feedback between the two problems, they are usually treated as separate tasks.The ultimate open pit is defined by the removal of whole blocks so that their net present value is maximised. This gives planners an estimate of the total worth of the venture in present terms, and is crucial to obtaining funding. All cost and profit values are assumed to be static throughout the mine life, and the only physical constraint usually taken into account is that of safe, average, wall slopes, which must be approximated by the removal of whole blocks. Modelling of any further constraints (for example, access roads and true wall slopes) is usually achieved by adding them to the optimal pit by hand. Typically this degrades the model by between five and 20 per cent of its value - which then brings into question whether it is still the true optimum.This paper reviews the dominant methods in use for this first task the ultimate open-pit planning problem. Some new optimisations are given, and the algorithms are examined in terms of their efficiency and accuracy. Finally, suggestions are made for improvement of model accuracy and eventual expansion into solutions of the more complete dual problem - that of simultaneously finding the optimum ultimate pits and dynamic schedules for the venture.

Jan 1, 1996

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

By C. W. Drury, E. J. Hall

The iron-nail method of assaying has been used for a number of years, but has not met with the approval of all assayers. The method possesses advantages which may be given as follows: (1) no preliminary treatment is required; (2) a lead button of proper size can be obtained; (3) it is economical. On the other hand, it has its disadvantages, which may be summed up as follows: (1) it is not applicable to ores containing large amounts of impurities other than sulphur, as practically all the base metals will contaminate the lead button ; (2) the slag is unsatisfactory in the larger number of fusions; (3) the method was known to give low silver results under certain conditions and the gold results were questionable. It was with the idea of determining the extent of this latter disadvantage that the following investigation was undertaken. It is well known that the fusion obtained in the lead assay is far more satisfactory than that in the " nails method" for gold and silver. The principal difference in the charges as a class is the presence of considerable reducing agent in the lead charge, and a limited oxidizing action in the nails charge, dud to PbO. The possibility of improving the nails fusion by simulating the lead charge was the reason for using argol in some tests, even though there were reasons for expecting this would have an objectionable effect on the results. Preparation of the Gold-Bearing Material. The materials containing gold and silver used in the following experiments were prepared rather than selected, in order to have a definite working product excluding undesirable elements. A high-

Jan 1, 1914

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By Peter N. Blakey, Thiann R. Yu, Douglas O. Tansey

A flexible, efficient, and relatively low-cost drilling and blasting operation has evolved at Texasgulf Canada, Ltd.'s Kidd Creek underground mine. Located 32 km (20 miles) north of historic Timmins, Ontario, the underground operation utilizes a sublevel open stoping method developed with large-diameter blastholes. Over the years, Kidd Creek engineers have experimented with various drill-and-blast techniques, leading to the present-day practice. Continuing work is being conducted to further mechanize the blasting operation.

Jan 6, 1976

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By T. S. Lovering

An economic geologist is concerned primarily with finding deposits of economic value, estimating their tenor and quantity, their shape and position. Thus the primary problems can largely be lumped under three headings: position, character and quantity; and all three are phases of the broader problem of genesis. Distribution, tenor and quantity are of immediate practical importance and are studied constantly by all who exploit mineral deposits. Although the emphasis changes from year to year, the problems of genesis seem more remote and rarely get the serious consideration from the field man that the other three do. Our understanding of the problems of the genesis of mineral deposits has come largely as a by-product of more evidently utilitarian work in the past, and probably will continue to grow in the same manner lor many years to come. However, it might be economically fruitful for the producers to have many competent investigators spending their time chiefly on the problems of genesis of mineral deposits. Many years ago, when first engaged in work for the United States Geological Survey in Colorado, I expressed a conviction which was just then dawning on me by saying that economic geology was turning out to be 80 per cent structural geology, to which Mr. B. S. Butler replied, "Yes, and more than 80 per cent of structural geology is lithology." At the present time there seems to be a widespread feeling among economic geologists that the problems of position or distribution are largely problems of structure and rock types. Types of Research Ptesearch in any branch of geology can be conveniently divided into two types: field research and laboratory research. Ideas are usually dug up in the field, pruned or developed in the laboratory, and taken back to the field for proving. For either the first or last step the field data should he as complete as possible, and the structural geology of nearly all our mineral deposits still needs more detailed delineation. In general, this means mapping on larger seales. Ideally the structural map should give a factual picture of a11 visible effects of stress; there is still room for vast improvement in the technique of presentation. Information that is much

Jan 1, 1940

By [Dipl. -Ing. ] Karl Angerer

The "New Austrian Tunneling Method" is one of the most significant developments in European tunneling in the last 15 years. I hope this report will show the significance of this tunneling method, which was developed in Austria exactly 18 years ago and which is now used in many European countries. In Austria from 1948 to 1953, the Moll tunnel with a length of 11.6 km (about 7.3 miles) was constructed as a part of the Kaprun power plant. Depth of overburden varied from 1000 to 1400 m, and there were many rock bursts in calcareous-schist formations. Here for the first time it was found that a thin concrete lining would help to prevent rock bursts if it was sprayed on the rock soon after blasting. During construction of the Prutz-Imst tunnel in Austria from 1953 to 1956, the shotcrete lining was sprayed on the phyllite surface a certain distance behind the blasting face to prevent rapid rock decomposition. This method was also tried in soft-rock sections of the tunnel where steel and wood supports usually were necessary. To prevent loosening of the rock, application of the sprayed concrete was tried immediately after blasting. This method made it possible to tunnel through very soft ground. Where necessary, the shotcrete was supplemented by steel arches and mesh reinforcement. At that time (1953-1956), the machines and equipment for guniting or spraying concrete were being improved rapidly and it became possible to spray aggregates up to 25 mm in diam. Hardening accelerators brought quicker strength and better adhesion of the shotcrete-this also made it possible to use the method in wet tunnels. If the tunnels are extremely wet or flowing with water, it is necessary to seal off the wet rock or drain the water, using, for instance, the Oberhasli method. After these first successful steps with the new Austrian method, large portions of the Schwarzach power plant in Austria were designed and built. At this operation, shotcrete was used almost exclusively for tunneling work. It was on this site where, for the first time, a tunnel 120 m long with a 45-sq- m section was driven through overburden without one piece of timber

Jan 1, 1970