Search Documents

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By J-P Franzidis, E V. Manl, K Runge

Over recent years a number of techniques have been developed as part of the Australian Minerals Industries Research Association (AMIRA) P9 project to represent mathematically or measure directly subprocesses occurring in flotation cells. These include the determination of a:machine parameter (bubble surface area flux, Sb); froth parameter (froth recovery, Rf); entrainment and drainage parameters; and ore floatability parameter (Pi). A cost-effective methodology was developed for using these techniques to derive models of flotation circuits. This methodology was applied to derive a model of the flotation circuit at the Western Mining Corporation (WMC) Ltd Mt Keith Nickel Concentrator. The model was used to simulate a number of minor circuit flowsheet changes, the results of which are discussed in this paper. One year later, a second study of this plant was conducted. In this second study, data were collected while operating the plant in the flowsheet configurations that were simulated from the model developed from the first study. The results obtained from the second study showed reasonable agreement with the trends predicted from the first study model; discrepancies can be explained in terms of the model assumptions. This suggests that this simple circuit modelling methodology can be useful in assisting plant engineers to optimise flotation circuits.

Jan 1, 2000

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Douglas R. Cook

The urgent need for new base metal ore discoveries was discussed by various authoritative exploration personnel at a CIM symposium on the future of the Canadian mineral industry held at Ottawa in 1967. Data presented at this meeting showed that approximately 150 new mines have started or restarted production in Canada since 1955. Over half of these mines were discovered prior to 1950. The distribution of Canadian ore discoveries during the last 15 years (shown in Fig. 1) illustrates a striking reduction in the discovery rate in recent years in spite of increasing exploration expenditures. These data indicate that $20 million is now spent in exploration for every significant metal deposit found, and evidently the cost of discovery is still rising. Even fewer discoveries are being made in some other important continental areas of the world such as Africa, Australia and South America. The discovery record in the U.S. is thought to be more rewarding than in Canada because the new deposits appear to be substantially larger. Fortunately, most good base metal ore deposits have attractive investment re- turns to justify large exploration expenditures. The magnitude of the exploration expenditures and the increasing need to develop additional metal resources justifies a critical review of the procedures used in the search for ore deposits. Of particular concern is the need to improve the use of exploration techniques in the attempt to obtain better discrimination and efficiency. There is a tendency by inexperienced exploration groups to think of any geological, geochemical or geophysical anomaly as an exploration target and ignore the fact that anomalies can result from many factors other than economic concentration of metals. The desire for a unique and favorable explanation of exploration data often results in too rapid a movement from the reconnaissance to the drilling stage without the use of all the relevant information.

Jan 7, 1968

By John W. Chang

Introduction Automatic control of primary ball mill circuits has received much attention over the past decade, primarily because its advantages ultimately can be translated into economic terms. Apart from such obvious benefits as improved product quality, increased throughput, and more stable operation, less direct benefits such as easier operation, more orderly maintenance scheduling, and timely management reports all can be realized with the application of modern automatic process control equipment and techniques. Software configurable digital computer-based control systems offer ease of change in control strategies. Occasional control strategy changes are necessary whenever control objectives change or circuit modifications occur. The dependency of control strategies on control objectives and circuit equipment to effect optimal circuit operation is an important, but often neglected issue. Because of the potential for even better control, research and development work continues. [See (Ulsoy & Sastry, 1981) and (Hulbert & Braae, 1981).] Some of the possibilities are discussed later in this presentation. A few preliminary remarks may be in order concerning the relationships among control objectives, control strategies, and circuit equipment. Generally accepted control objectives for primary ball mill circuits include: 1. Maintaining a desired percent solids in the mill. 2. Maintaining a desired measure of particle size distribution at the cyclone overflow. 3. Maximizing throughput. Control Objective I is a requirement for proper operation of the ball mill, especially if it is a grate mill. It concerns smooth movement of material through the mill. Control Objective 2 is a product specification - one of the requirements for proper flotation operation. Control Objective 3, an expression of the desire to get the most out of the circuit, is the easiest to evaluate in economic terms. It assumes that the processes downstream

Jan 1, 1982

By F. H. Wilson, E. W. Palmer

G. L. Bailey (British Non-Ferrous Metals Research Association, London, England)—I was glad to see this further work on the structure and properties of the Cu-Ni-Fe alloys of low nickel content in which we have been so interested in the United Kingdom since before the war." The authors' data on the variation in solubility of iron in both 5 and 10 pct Ni alloys with temperature is based on more detailed observations than we have made but is generally in line with our own work. The difficulty in these matters is in the identification of the structures obtained. The precipitation of the second phase which we presume to be the a' solid solution, richer in nickel and iron, from the a solution with which it is in equilibrium occurs in such a fine state of division that its resolution by ordinary micro-graphic methods is impossible in the early stages. We have published some electron micrographs which illustrate the effects observed more clearly but we agree with the authors when they say that dark staining characteristics when the alloys are subjected to sea-water corrosion are more sensitive in detecting the presence of the a' phase than is the microscope. After taking this point into consideration, however, I confess to some difficulty in understanding Fig. 4. I can only assume that the precipitates visible at such a low magnification as 150 diam in these relatively coarse forms are produced from iron-rich areas of the initial solid solution due to inadequate homogenization. If this is so I find it difficult to accept the authors' contention that such local variations in iron concentration as are capable of giving the heavy precipitates shown in Fig. 4 do not in fact materially affect the solvus surfaces of their equilibrium diagrams. I share the authors' enthusiasm about the resistance to corrosion of these alloys by seawater but I am not fully in agreement with them on the vexing question of the best iron content for these alloys. In Fig. 3 of ref. 8, we give many results showing that the resistance of these alloys to impingement attack in the Jet Test increases as the iron content rises to 2 pct. With higher iron contents pitting at shielded areas is likely to occur. Admittedly the addition of 0.75 pct Fe produces a large improvement in corrosion resistance compared with a pure 90/10 Cu-Ni alloy, but the further improvement on raising the iron to 2 pct is substantial. We recommend from 1.5 to 2 pct Fe as the desirable range from the point of view of corrosion resistance. While it is true that British practice generally uses a hard tube, the corrosion resistance of the 10 pct Ni alloys has in our work been little affected by the structural condition. Although the annealed alloys blacken in seawater, this effect seems to be superficial and not to be accompanied by any real decrease in

Jan 1, 1953

By G E. Craig, W. M. Williams

A simple, easily constructed apparatus suitable for the zone refining of iron and other reactive materials is described. After eight passes at one inch per hour, the iron produced showed a marked drop in hardness to 49 Brinell. In addition, an arbitrarily -defined recrystallization temperature was lowered by about 35°C and the rate of grain growth greatly increased. CERTAIN materials, of which iron is one, are so reactive that they cannot be zone refined in any known container without becoming contaminated. For such substances, the floating zone method ( 1) may be used. In this method, the specimen is supported vertically in an inert atmosphere and the molten zone supports itself by its own sur-face tension. The method was first applied to silicon (2) and has since been used for other reactive metals such as zirconium and titanium. Smith and Rutherford (3) have previously reported on the floating zone refining of iron; the efficiency of the method for reducing the car-bon content was demonstrated on

Jan 1, 1962

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By H. Gumede

The challenges of noise emission in the mining industry are well known. These challenges are exacerbated by the increasing trend towards mechanized mining, and there is general consensus that an effective industry-wide Buy Quiet initiative (BQI) will significantly assist in reducing noise-induced hearing loss by minimizing noise at its source. In its endeavours to improve the health of workers, the MOSH Noise Team has facilitated development of a proposed strategy and structure for a BQI. Extensive consultation with stakeholders resulted in support for the initiative. The MOSH Noise Team was advised to solicit the contributions of consulting mechanical and electrical engineers (CM&EEs), whose support is viewed as critical for realization of the initiative, since elimination of noise at source is an engineering challenge, and most procurement standards and specifications are set and managed by engineers. A workshop with CM&EEs and their representatives, as well as group environmental engineers (GEEs), confirmed the urgent need for the initiative and provided valuable insights. The workshop used obstacle based planning techniques to identify the factors on which the success of this BQI will depend. Most potential obstacles to the implementation revolved around proper scoping, leadership commitment, and companies? adherence to the initiative. Lack of involvement by the relevant stakeholders and economic issues were also identified as potential obstacles. Delegates at the workshop felt that the successful implementation of the industry-wide BQI, will depend on the mining industry addressing the specific obstacles. The most critical and urgent issue was identified as the formation of a properly constituted industry-wide BQI task team that includes representatives from critical stakeholder groups and which is mandated and empowered to drive the initiative.

Jan 1, 2014

By M. A. Sobhi, L. Li

With the continuous reduction of mineral resources at shallow depth, more and more mines have to go deeper beneath the earth's surface to reach the ore zones. This increase in mine depth leads to a natural stress increase, which also raises the stresses around mine openings. This may result in ground instability, including the risk of rock bursts or exceedingly large opening closure. Stope backfilling is a well known solution to improve the ground stability condition. It also has the advantage of reducing the mining wastes disposed on surface, thus helping to reduce the environment impact from the industry. However, most available solutions for backfill design were developed for an isolated stope without taking into account the influence of mine depth, except for a few numerical analyses performed recently by Falaknaz and coworkers for the case of multiple backfilled stopes laying in the same level. In this paper, a numerical study is carried out to evaluate the stresses in backfilled stopes overlying a sill mat. The mine depth and the excavation of the underlying stope below the sill mat are both taken into consideration. Compared to the case of a single isolated backfilled stope, the obtained numerical results show that the stress magnitudes in the overlying backfill are considerably increased due to the excavation of the underlying stope. In general, the stresses increase with mine depth and backfill stiffness, but decrease with an increase in the surrounding rock mass stiffness. These results indicate that the barricade and sill mat backfill design should take into account the excavation of the underlying stope and the mine depth.

Jan 1, 2015

By AIME AIME

T HE Mid-Continent Section of the Petroleum Division met on Mar. 11 in the engineer's room of the Tulsa Building, Tulsa, Okla., for the purpose of reviewing the papers presented at the annual meeting in New York. L. G. E. Pignell, chairman and delegate to New York for the Mid-Continent Section, read a brief report giving the outstanding features of the various papers that were presented. He expressed regret that more members of the Division could not be present in New York to hear the interesting papers and discussions. It was his opinion that the various remedies presented for overproduction seemed rather theoretical and impractical and he recommended that the engineers come to the aid of some of the economists in giving more practical consideration to the overproduction problem.

Jan 1, 1929

By M E. Barley, A D. George, M Kneeshaw

Detailed pit and outcrop mapping of sedimentary rocks and their alteration is providing insights into fluvial processes that operated during deposition of the world-class Yandi channel iron deposit. Five prominent rock units are traceable along the strike of the Yandi deposit and permit correlation of open pits and mesas. These units are the Eastern Clay Horizon (ECH), granule-pebble conglomerate (GPC), Main Ore Zone (MOZ), Basal Denatured Zone (BDZ), and Basal Conglomerate (BCONG). The upper part of the deposit is characterised by a transition from spheroidal grains with well-defined rims and nuclei to larger, subangular grains with poorly developed rims. The distribution of rock types and sedimentary features such as lateral accretion surfaces, channel scours and fills, graded bedding, cross-bedding, reworked horizons, and slumped strata are common at Yandi and indicate deposition in a fluvial system. Bedding is well preserved despite modification of original grain shapes and textures and introduction of secondary silica and alumina in the upper part of the deposit. The high lithic and clay content of the GPC and ECH possibly reflect changes in source area or a hiatus in deposition of the Marillana Pisolite. The MOZ and the BDZ may be the same depositional unit with the latter recording alteration by groundwater and destruction of primary textures and other sedimentary features. The BCONG is a channel lag deposit reworked during deposition of the MOZ. This interpretation is supported by the dominance of basement-derived lithic clasts, the presence of BCONG clasts, the variable thickness of the unit along strike and the presence of BCONG clasts in the BDZ.

Jan 1, 2002

By Charles H. Fulton

One of the first matters to receive attention from the Bureau of Mines when it was authorized to undertake investigations relating to wastes in the mineral industries was the smoke problem at smelting and ore-roasting plants. This bulletin is published by the bureau primarily for persons who seek information on the subject of metallurgical smoke but are unacqllainted with the technical language of metallurgy. It is, of course, not possible to free a techniCal subject entirely from teclmicalities, but, 80 far as possible, statements are made in plain and simple English. Metallurgical smoke causes considerable friction between the metallurgical industry and agriculture in certain parts of the country. Owners of smelting plants are making every effort to devise ways and means to do away with possible damage and annoyance from smoke and are meeting with success. The problem is peculiarly difficult in this country because of the large tonnages of material that must be handled. The solution of the problem is not yet at hand and much work still remains to be done. As the mineral industry is one of the great basic industries of the country and of necessity is entitled to full consideration, it should be accorded freedom to work out the smoke problem to the benefit of all concerned. The effort is made in this paper to present the problem of metallurgical smoke as it actually exists, without bias of any kind. The writer takes this opportunity to express his indebtedness to the sources of information on which he drew, many of which are enumerated in the selected bibliography at the end of this paper. In connection with the author's use of the present tense in describing plants and methods, the reader should note that none of the references in that bibliography is of later date than 1913. Much information was obtained by personal visits and by correspondence, and thanks are hereby tendered to all persons who kindly furnished data. The writer desires to thank particularly F. G. Cottrell, chief chemist of the Bureau of Mines, for criticism and comment.

Jan 1, 1915

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

1. ACKERMAN, C. L. The Binary System Manganese-Zinc. Ztschr. Metall., vol. 19, 1927, p. 200. 2. ADKENASY, P., AND KLONOWSKY, S. Über die Manganatschmelze. Ztschr. Elektrochem., vol. 16, 1910, p. 107. 3. AKTIEBOLAGET FERROLEGERINGAR (assignees). Method for the Manufacture of Manganese Alloys Poor in Carbon or Silicon or Else Manganese. British Patent 163262, Apr. 28, 1921; U. S. Patent 1480267, Jan. 8, 1924. 4. Method of Producing Manganese or Manganese Alloys Poor in Carbon or Silicon. British Patent 174923, Jan. 25, 1922.

Jan 1, 1934