Search Documents

By John B. Pearse

THE works heretofore used in carrying out the Bessemer process have been constructed substantially as follows : The whole works or plant has been divided into three parts. 1. The division in which the metals for conversion are melted. 2. The division in which the metals are converted into steel and cast into ingots, or the converting department. 3. The engine and boiler department which supplies the hydraulic power required to move the machinery, and which furnishes the blast used for converting the crude metal into steel.

Jan 1, 1876

By W. A. Yuill

A process has been developed for increasing the grade of chalcopyrite concentrates from about 25 percent copper to about 60 percent copper. The concentrates are treated with two steps of autoclaving and then by flotation. Because of the lower associated weight, copper in the concentrates could be shipped and smelted at less cost than untreated concentrates. Use of the process can also increase overall yield from an orebody if a lower grade concentrate is sent to enrichment than would be sent to a smelter. Potential applications of the process would be for treating concentrates that must be transported a long distance for smelting or for treating concentrates so as to increase the capacity of a smelter.

Jan 1, 1984

By S. Caron, M. Bourassa, J. Châteauneuf, L. Tardif

"Since many years, the Yvan-Vézina gold plant custom mills and processes different ore types that show different behaviors. Because of this, cyanidation control is more complex than for a typical milling operation. In 1992, a Cyancor™ on-line « free cyanide » analyzer has been installed for monitoring and optimizing cyanidation. This implementation significantly reduced cyanide consumption for the overall cyanidation process. In order to further reduce cyanide costs, an automatic control strategy has been implemented to decrease fluctuations of« free cyanide » from their set points.This paper outlines the major steps of the project: process control audit, control strategy development, implementation and running-in period. Control strategy features include data filtering modules, adaptive PID algorithm and set points management modules are also presented. Finally, the strategy efficiency is illustrated with load-disturbance responses.IntroductionLocated in northwestern Quebec, the Yvan-Vézina plant has an average capacity of 1300 t/d using carbon-in-pulp technology. In 1991, the Yvan-Vézina gold plant was processing three types of ores (Beauchemin, Mouska and Silidor mines) and a pyrite concentrate (Beliveau mine). A cyanide reduction program was then undertaken to reduce « free cyanide» fluctuations <6>. To reach this objective, the optimum cyanide concentration was determined for each ore, a continuous monitoring method with the Cyancor™ on-line analyzer was developed and a tighter control of cyanide addition was applied. These modifications to the leaching practice significantly reduced cyanide consumption.After a while, it was observed that regulation of « free cyanide » concentrations could still be improved by the use of an automatic control strategy. Yvan-Vézina and CRM began collaborating in 1995 to develop and implement such a strategy. Results show that main disturbances of the circuit (e.g. ore mineralogy and pulp feed rate) can be significantly overcome in order to reduce their effects on the leaching operation."

Jan 1, 1998

By Peter G. Tregelles, Derek K. Barham

Introduction A successful step towards mechanisation of the collier&apos;s work was taken in 1954 when the first Anderton shearer loader was commissioned in Lancashire, and progress was reinforced in 1956 when the first powered supports were installed in Nottinghamshire. By 1970, virtually 100% of the coalfaces in the United Kingdom were mechanised and the industry&apos;s productivity had doubled. In 1961 the National Coal Board recognised that the next move towards greater productivity and improved safety would be to automate the longwall system. What was not well enough understood, however, was that the basic prerequisites of automation - reliability and measurement - had not yet been achieved. Consequently, the schemes for automatic longwall faces and for an entirely automated colliery were abandoned at the close of the decade. A review of mining research and development policy, commissioned by the Board in 1974, confirmed that the system of longwall mining had great potential for investment and that the short-term policy of automation must once again be pursued. Since then, aided by advances in computer technology, systems for automating the transport of coal from the face to the coal preparation plant have been successfully instituted. Applications of sub-systems dealing with the conveyor, coal preparation plant, and various items of fixed plant are now at the exploitation stage. In the medium term, a number of key problems have been identified, which will arise once the productivity from the coalfaces has doubled, as it is now expected to do in the next five years. One of the most important of these problems is machine guidance, and considerable research and development work is now being carried out in this area. This paper reviews the work on machine guidance prior to 1974 and explains the programme on which the National Coal Board&apos;s Mining Research and Development Establishment is currently working.

Jan 1, 1981

By Oscar A. Glaeser

The purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings. Need for Ventilation The range between the maximum oxygen content of normal air and the minimum safe content is extremely narrow, approximately 5 per cent. Furthermore, normal air must not be contaminated with irrespirable gases beyond definite limits, and mineral dusts are equally dangerous, although health impairment is slower. Tables 1 and 2 present the more common respiratory hazards encountered in mines. Adequate ventilation is the most effective means available to reduce or eliminate these hazards. Mechanical ventilation has reached varying stages of perfection in coal mines and in many large metal mines. The small mines and prospects rarely have a definite plan of ventilation. As a consequence underground workers are frequently exposed to health and accident hazards. The annual reports of fatalities in mines in the Western States record yearly many deaths due to asphyxiation and deaths caused by men falling down shafts and raises after being overcome by gas. At times mining operations are slowed up because there is no means of driving out the gas after blasting. For that reason only one shift is worked, or men wait from one to several hours for the "smoke" to clear out. Methane gas in varying quantities is widely distributed throughout California. It has been encountered in explosive concentrations in the coast range. It has been found on the Mother Lode and in quicksilver mines near the coast. Methane explosions have not been uncommon in underground operations and in tunneling jobs. These conditions and records indicate that there is room for improvement in mine-air conditions.

Jan 1, 1937

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

By R. K. Mehta, C. W. Schultz, J. B. Bates

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained. Experimental equipment and procedure The arrangement of the column cell and auxiliary equipment for continuous flow testing is shown schematically in Fig. 1. The feed sump [O] is filled with a sufficient volume of prepared sample to permit a large number of tests to be performed (typically 12). Past experience has shown this is necessary to control sample variability and variability in the size distribution resulting from ultra fine grinding. The feed slurry is maintained at about 20% solids and is constantly recirculated and stirred. The sample is metered from the circulating pipe by a peristaltic pump [O]. The feed slurry is diluted with reagentized water [O] by a second peristaltic pump [O]. Wash water [O], also reagentized, is supplied through a third peristaltic pump [O]. While this feed system may seem unduly complex, it does permit users to independently vary either the wash water rate or the net solids content of the cell. In the tests reported here, the feed rate and net percent solids were constant at 12.5 gms/min. and 3.3%, respectively. Diluted feed enters the column through 6.35 mm-diam (0.25 in.-diam) copper tubing and is discharged upwardly at the center of the column. Tailings are discharged through flexible tubing that can be adjusted so as to control the position of the pulp-froth interface. The column is 76.2 mm-internal-diam (3 in.-internal-diam) and 1090 mm (43 in.) high. It is made from lucite tubing and is fitted with a 51-mm-diam (2-in.-diam) fritted glass air sparger having an average pore diameter of 50 µm. In performing a series of tests, the concentrate and tailing are allowed to discharge continuously. The system is allowed to equilibrate for 30 minutes after the pulp and froth reach operating levels. Concentrate and tailing samples are taken simultaneously for timed intervals (five to 15 minutes, depending on the volume of sample desired). After sampling, a change in operating conditions is made and the system is again allowed to equilibrate. The tests to determine the effect of the pulp-froth interface level were part of a larger series of tests in which the objective was to optimize the conditions for a rougher flotation stage in a two stage circuit. The sample used in this series of tests was an Alabama shale ground to d90 = 23.1 µm and d50 = 7.9 µm. The operating conditions remaining constant in this series of tests were as follows: Column height - 1600 mm (63 in.) Air sparser - 50 µm (average pore diameter) Spray water - 130 cc/min. Feed rate - 12.5 gm/min (0.4 oz per min) (dry solids) Percent solids - 3.3% Frother (Dowfroth 250) - 45 ppm The variable test conditions are tabulated in Table 1. Positions of the pulp level (pulp froth interface) and feed entry are presented as a percentage of column height (as measured from the face of the air sparser). These test conditions are presented Fig. 2. At each of these test conditions, individual tests were performed at varying air

Jan 1, 1992

By G. R. Baiden

Introduction The introduction of teleremote systems to underground mining can provide a significant improvement in the performance of a mine when compared with conventional mining techniques. This paper presents the concepts of teleremote mining in a case study showing how the systems work and the competitive advantage autonomation of mining techniques will provide for underground metal mining operations into the future. This paper is divided into two sections: the Mining Automation Program and What is next? On January 1st 1996 Inco Limited, Tamrock Oy, DYNO Explosives Group and CANMET formed a consortium for the development of teleremote mining equipment called the ‘Mining Automation Program’ or MAP. This program included a five-year research and development agreement that combines the talents of the above organizations to create mining equipment and systems for autonomating mining. The projects are based on the communication system currently sold and marketed by Automated Mining Systems Limited. The main components of the program investigated the development of a positioning and navigation module, autonomated systems using teleremote techniques for development and stoping, and software systems to support the use of this equipment. The program included the establishment of a test mine, at Inco’s 175 Orebody near Copper Cliff North Mine. This facility was unique allowing collaboration of companies and research organizations inthe design and testing of techniques and equipment used to apply autonomation to mining. Since the inception of the project other research alliances have been added to enhance the program. These include the application of ground support (Meyco/ Master Builders), muck pile recognition, the broadening of telecommunications links (PRECARN Associates Inc.-MALTA project) and the collection and processing of drilling core through the automated diamond drilling project (J.K.S. Boyles). MAP began as an idea a number of years ago with the fundamental question ‘Can an ore-body be profitably mined through autonomation?’ The concept was to design mining equipment and systems that would allow the teleremote operation of a mine. Automation was only one componentof this much larger teleremote mining issue. To start with, it was essential to prove or disprove the feasibility of this concept. The fundamental requirements are: • Telecommunications • Positioning • Navigation • Equipment • Software • Electronics • Mining Engineering • Organization. Each of these had to be considered. Technically, the feasibility of the project hinged on the successful development of a high capacity communication network, an accurate underground positioning system, a navigation system and finally the electronics and software that could integrate these. Mining equipment that could perform all the mining functions was the next requirement, along with explosive supplies that could be delivered to the holes teleremotely. Whatever the systems developed, they must be able to work in both bulk and selective mining situations and in varying conditions within a mine. Finally, the organizational issues of a change from our current method of operation to teleremote mining had to be understood. After five years of research and development the answer to the question ‘Can an orebody be profitably mined using autonomation techniques?’ is YES! There are still hurdles to overcome, however, the basic premise has been proven. The development and production of underground tunnels and stopes has been done. There have been interesting outcomes in terms of reduced effort to accomplish mining and the total time to mine. Definitions •Automationis the process by which a machine or system is run continuously including the ability for the system to self-correct. •Autonomationis the same as automation except that the process does not self-correct. •Teleremote operation is the operation of mining equipment over a network from any location out of line-of-sight of the machine. •Equipment Automationis the addition of technology to a machine that allows for unmanned operation of a machine and thus enhances the productivity of the operator. For example, a guidance system that allows a load-haul-dump to drive by itself, thus freeing the operator for other tasks. •Teleremote mining describes a mine process that combines the use of teleremote operation (potentially with some automation), positioning and process engineering, monitoring and control. •Tamrock DataSoloTMis a computerized drilling rig as shown in Figure 1. •Tamrock DataMini™ is a computerized development drill rig used for drifting and construction tunneling as shown in Figure 2.•Tamrock Toro 450™ is a LHD (Figure 3).

Sep 1, 2001

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900&apos; to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,&apos; nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.&apos; In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By Rafael Duclou Rito

Com temperaturas altíssimas atingidas, os fornos são equipamentos responsáveis pelo aquecimento de materiais na produção de tubos sem costura. Assim, o investimento requerido de um forno em bom funcionamento é quase todo em combustível. Este trabalho foi desenvolvido objetivando a qualidade dos produtos e a otimização dos períodos em que o forno não produz. Durante os períodos citados, o forno é desligado ou mantido a uma temperatura menor que a de operação. Estudando a transferência de calor, principalmente no refratário, é possível analisar a melhor prática em situações improdutivas. Portanto, foi desenvolvido um simulador da temperatura dos refratários ao longo do tempo do forno em questão, sendo possível espelhar parâmetros reais para encontrar o controle de temperatura ótimo do forno, em que a temperatura da atmosfera interna é a principal entrada no programa. Termopares foram instalados ao longo das paredes refratárias para que o modelo fosse validado e aprimorado. Paralelamente, pontuou-se a relação dos materiais enfornados com as medições dos termopares, a fim de encontrar uma temperatura ideal de enfornamento. Os resultados foram positivos e permitem o uso de artifícios de refinamento dos resultados.

Oct 30, 2017

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe&apos;s formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

By T. M. Barczak

This report describes Bureau of Mines research to develop methods to evaluate loading on longwall roof supports to permit better design and more efficient utilization of these structures in compliance with the geological conditions in which they are employed. The resultant vertical and horizontal force acting on the canopy of a shield can be determined, either from a statically determinate solution assuming rigid-body mechanics and elimination of certain unknowns, or from an elastic solu-tion by analysis of the load-displacement relationship of the shield structure. A two-dimensional rigid-body model is presented that determines resultant shield forces by measurement of leg, canopy capsule, and lemniscate link forces. An elastic solution is presented, in the form of an elastic stiffness model with two degrees of freedom, which describes the load-displacement relationship from the stiffness of the shield structure as determined in the Bureau&apos;s Mine Roof Simulator (MRS). The ability of both models to determine resultant forces acting on the shield canopy are evaluated from full-scale tests in the MRS. More advanced numerical models are also discussed as part of the Bureau&apos;s continuing effort in the evaluation of roof support structures.

Jan 1, 1987

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By Frank B. Fulkerson

Mining began in Pend Oreille and Stevens Counties about 1885, Lead and zinc have been the principal products, and the area has supplied nearly all the output of these metals in the State. Fend Oreille County&apos;s output of lead and zinc from 1902 to 1956 was 110,700 and 229,600 tons, respectively. The Stevens County total was 54,100 tons of lead and 87,600 tons of zinc. Copper ore was produced mainly from the United Copper mine, Chewelah district, from 1912 to 1920; the principal gold mine was the First Thought, Orient district, which was active from 1904 to 1942. Approximately 225 mines and prospects produced; most of the ventures were on a small scale. The total value of gold, silver, copper, lead, and zinc produced from 1902 to 1956 was $75.2 million in Pend Oreille County and $39.4 million in Stevens County. INTRODUCTION In compiling the figures for this report, use was made of Bureau of Mines permanent records of nine production, the annual tabulations of producing mines, and the Minerals Yearbook. Requests to publish individual data, obtained from the annual production canvass, were made to the latest recorded operators of all mines in the area. Response to this request was good; therefore, it was possible to make the tables nearly complete. In a few instances the producer requested that the production data remain confidential, and in others it was not possible to reach the mine operator at his last known address. The district and county tables combine statistics for all mines, including those mines whose output could not be published separately.

Jan 1, 1958

By K. J. Palmer, D. A. Silva

"Evaluating resources and reserves requires the reliable modelling of geological domains and their grades. “Multiple point statistics” simulation is a relatively new geostatistical method to generate complex, high-resolution geological models by extracting high-order spatial relations from training images. A method based on combining multiple training images is developed to obtain the correct amount of large-scale continuity and short-scale variability. A calibration process matches the geological spatial variability between the final realizations and the drillhole dataset. A case study with data from the Red Dog mine, Alaska, United States, shows an appropriate reproduction of short-scale variability along boundaries between geological units.RÉSUMÉ L’évaluation des ressources et des réserves exige une modélisation fiable des domaines géologiques et de leur teneur. La simulation par « statistique multipoint » est une méthode géostatistique relativement nouvelle pour générer des modèles géologiques complexes à haute résolution par l’extraction de relations spatiales d’ordre supérieur à partir d’images d’entraînement. Une méthode basée sur la combinaison de multiples images d’entraînement est développée afin d’obtenir la bonne quantité de continuité à grande échelle et de variabilité à petite échelle. Un processus d’étalonnage fait correspondre la variabilité géologique spatiale entre les réalisations finales et l’ensemble des données de forage. Une étude de cas avec des données de la mine Red Dog, Alaska, États-Unis, montre une reproduction adéquate de la variabilité à petite échelle le long des limites entre les unités géologiques."

Jan 1, 2015

By Alfredo Gallardo

El artículo da cuenta de la investigación desarrollada por Compañía de Minas Buenaventura, para formular —con miras al cierre de la unidad minera La Zanja— una cobertura de suelos con residuos mineros que permitan la impermeabilidad, estabilidad física, biológica y geoquímica de los componentes generadores de drenajes ácidos de mina. Buenaventura adecuó un antiguo depósito de desmontes y lodos para realizar pruebas y ensayos que incluyeron el uso de suelos mejorados, suelos artificiales, suelos construidos —conocidos como tecnosoles—, con el fin de adaptar esta tecnología, desarrollada en Canadá y España, a la realidad peruana.

Nov 30, 2020

By Gisele Ferreira de Lima

Magnésio e suas ligas são promissores para armazenagem de hidrogênio devido à alta eficiência, boa reversibilidade, baixo custo e segurança. Entretanto, hidretos à base de Mg apresentam cinéticas de ab/dessorção lentas, temperaturas de operação muito altas, e alta reatividade ao ar para aplicação práticas. A moagem de alta energia (HEBM) combinada com o uso de catalisadores têm produzido nanocompósitos à base de Mg com cinéticas mais rápidas. Recentemente, processos termomecânicos e de deformação plástica severa (SPD) têm sido investigados para produzir nanocompósitos em volume com melhor resistência ao ar (processo de ativação) e que podem ser facilmente fabricados em escala industrial. No presente trabalho, amostras 2Mg-Fe foram misturadas com CNT (0-5%p.) por HEBM, e em seguida processadas por extrusão a quente (termomecânico) a 300oC e/ou laminação a frio (SPD) a temperatura ambiente. Pós com 0%p a 5%p. de CNT mostraram padrões de DRX muito similares indicando similares nanoestruturas. Todas as amostras puderam ser laminadas, mas somente amostras com menos que 2,0%p. de CNT puderam ser extrudadas, e submetidas pela combinação de extrusão-laminação. As propriedades cinéticas, medidas pelos métodos Sieverts e DSC, foram piores para as extrudadas, intermediárias para as extrudadas/laminadas e melhores para as somente laminadas. Nessas últimas, os picos de Bragg mostraram baixa intensidade e textura favorável ao longo de (002) no Mg, que possivelmente explicam esses resultados. Quanto maiores foram as quantidades de CNT melhores foram as propriedades (cinética e temperatura de dessorção).

Aug 8, 2018

By R. C. McFarlane, T. D. Mueller, J. E. Walstrom

In evaluating uncertainty, experiments are usually performed repeatedly and then conclusions are drawn from the distribution of results. With the advent of high-speed electronic computers, it is possible to perform experiments using mathematical models constructed to simulate complex experiments or operations. Statistical methods are then applied to the results of the simulated experiments. This procedure forms the busis of this paper. Demonstrated is the need for properly accounting for uncertainty in petroleum engineering problems. How uncertainty affects solutions is evaluated in three example illustrations. The method used to evaluate uncertainty in petroleum engineering studies is the Monte Carlo simulation procedure.&apos;-" INTRODUCTION The solution to most technical problems may be derived from interrelationships among several quantities called variables or parameters. There may be only a few variables or several hundred. Interrelationships among parameters may be explicit or implicit, well established or only approximate. Some variables that fully or partially depend on the magnitude of others are called dependent variables. Input variables for most practical problems are not precisely known; there is usually an uncertainty in their value. The degree of uncertainty may vary from one variable to another. Variables that are known accurately are called determinates.&apos; For instance, the gravity of crude obtained from a particular pool may be known precisely, and therefore is a determinate. The degree of precision with which a quantity can be determined increases as data describing the pool are accumulated during the development of the field and the producing life of the pool. The uncertainty of a parameter may result from difficulty in directly and accurately measuring the quantity. This is particularly true of the physical reservoir parameters which, at best, can only be sampled at various points, and which are subject to errors caused by presence of the borehole and borehole fluid or by changes that occur during the transfer of rock and its fluids to laboratory temperature and pressure conditions. Uncertainty may also result in attempting to predict future parameter values. This type of uncertainty is particularly evident in investment analyses involving future costs, prices, sales volumes and product demand. Uncertainty in the solution to investment problems is often called risk, and its study is called risk analysis.&apos; Uncertainty also enters into biological and sociological analyses in which indeterminate factors are often important due to limited control of the experimental material. It is customary, in evaluating uncertainty, to perform repeated experiments and to draw conclusions from the distribution of the results of these experiments. With the advent of the high-speed electronic computer, it is possible to construct mathematical models which simulate complex experiments or operations and to perform the experiments repeatedly, utilizing the models. Statistical methods are then applied to the results of the simulated experiments This method forms the basis of the investigation reported here. PROBABILITY DISTRIBUTIONS FOR VARIABLES The uncertainty in the value of a variable may be indicated by a probabilistic description accomplished by expressing the quantity by a probability distribution. Many recognized probability distributions can be used to describe physical quantities. Recent studies used various types of distributions to describe core analysis data.&apos;,&apos; However, for the examples in this paper, the uniform and triangular distributions are believed to reasonably approximate the data used (Fig. 1). The uniform distribution confines the variable between an upper and a lower limit. The variable may lie anywhere between the two limits. This distribution is used when no one range of values for a variable is more probable than any other, but information or intuitive reasoning indicates the variable will lie somewhere between the chosen limits. The triangular distribution is used for a variable when more data are available to indicate a central tendency of distribution. This allows postulating a "most likely" value to the distribution and upper and lower limits. In this case, as for the uniform distribution, the variable is not expected to assume a value less than the lower limit or greater than the upper limit. However, with improved quality of data it can be postulated that the variable will tend to assume a value close to the most likely value, and that there will be a decreasing probability for values away from the most likely value. The area under either of these probability distributions is equal to unity since it is assumed that there is a 100 percent probability that the variable will lie somewhere under the curve. An ordinate erected at any particular value of the variable divides the area under the curve into two parts: the area to the left of the ordinate represents the probability that the value of the variable will be equal to or less than the value of the variable at the position of the ordinate, and vice versa. The probability is zero that the variable will have any specific deterministic value. If two ordinates are drawn for any two values of the variable, the probability that the variables will have a value lying between these ordinates is equal to the area under the curve lying between the ordinates.