Search Documents

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By R. I. Iacobescu, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, P. Knops

In this work, we explore a novel mineral processing approach using carbon dioxide to promote mineral alterations that lead to improved extractability of nickel from olivine ((Mg,Fe)2SiO4). The precept is that by altering the morphology and the mineralogy of the ore via mineral carbonation, the comminution requirements and the acid consumption during hydrometallurgical processing can be reduced. Furthermore, carbonation pre-treatment can lead to mineral liberation and concentration of metals in physically separable phases. In a first processing step, olivine is fully carbonated at high CO2 partial pressures (35 bar) and optimal temperature (200 °C) with the addition of pH buffering agents. This leads to a powdery product containing high carbonate content. The main products of the carbonation reaction include amorphous colloidal silica, chromium-rich metallic particles, and iron-substituted magnesite ((Mg1- x,Fex)CO3). Carbonated olivine was subsequently leached using an array of inorganic and organic acids to test their leaching efficiency. Compared to leaching from untreated olivine, the percentage of nickel extracted from carbonated olivine by acid leaching was significantly increased. It is anticipated that the mineral carbonation pre-treatment approach may also be applicable to other ultrabasic and lateritic ores.

Jan 1, 2014

By S Vearncombe

SpaDiSÖ is a revolutionary approach to the spatial analysis of point data using geometry to analyse geometry! SpaDiSÖ uses each and every spatial relationship and is not dependent on mathematical models. For n points there are n2 û n spatial relationships and, because of the square function, the method yields interpretable results for both small and large data sets. SpaDiSÖ is an alternative to variography for directional studies. At the regional scale, the analysis can assess distribution patterns of mineralisation and potential controlling structures. At the deposit scale, the characteristics of zones of mineralisation such as direction, spacing, high-grade ore direction and grade distribution can all be deduced.

Jan 1, 2000

By Heine Kenworthy

"INTRODUCTION In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral content of this ore was considerably higher than in, the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently, tailing losses, especially with respect to lead, were high. A few years later, in order to study the possibilities of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill, feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Sta¬tion for testing-. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values was present.A résumé of the ore-dressing treatment used in the Shenandoah-Dives mill follows. After crushing, the ore passes through a ball mill, the minus 5-mesh discharge of which is distributed to three tables. A finished lead concentrate is made on the tables, and the table tailing goes to the classifier which is in closed circuit with the ball mill. The classifier overflow is treated -by flotation to obtain a bulk sulfide concentrate at a relatively coarse size. The bulk concentrate is thickened and reground to about 95 percent minus 325-mesh before flotation treatment to separate a lead-copper and a zinc concentrate. A typical monthly average showed that the table concentrate contained about 45 percent lead, 1 percent copper, 4 percent zinc, 12 ounces of gold, and 40 ounces of silver; that the lead flotation concentrate contained '35 percent load, 6 percent copper, 7 percent zinc, 3.5 ounces of gold, and 50 ounces of silver; and that the zinc flotation concentrate contained 2 percent lead, 0.5 percent copper, 60 percent zinc, 0.15 ounces of gold, and 4 ounces of silver. Recoveries in salable products were roughly b5 percent of the lead, 70 percent of the copper, 45 percent of the zinc, 85 percent of the gold, and b5 percent of the silver."

May 1, 1948

By L. J. Cabri

The level of mineral exploration activity for platinum in recent years, especially in North America, has ranged widely. Exploration programs have been based on a variety of ore deposit models and deposit types. These range from the classic magmatic model for sulfide/oxide deposits and their associated placers, through hydrothennal models for bonanza-type deposits, to low-grade mineralization potentially amenable to lower cost bulk mining methods. The platinum-group element (PGE) distribution in these different deposit types is not well-known however, and PGE determination is fraught with analytical difficulties. To properly assess a prospect or to achieve effective recovery by mineral processing, it is important to determine the mineralogical distribution of the PGE.

Jan 1, 1988

By Yuting Xue, Taghi Sherizadeh, Mark Van Dyke, Dogukan Guner, Khaled Mohamed

The Coal Pillar Rib Rating (CPRR) technique has been developed to assist in rib support design in underground coal mines. One major challenge of the data collection process is the measurement of coal strengths in the field. Schmidt hammer has been verified as a useful tool to determine coal strength. An alternative approach is to obtain the representative strength of coal mass by determining the coal lithotypes in the field based on the coal brightness profile by experienced geologists or mining engineers. In this paper, image processing techniques have been used to quantify the texture of coal images of different lithotypes with the purpose of classifying coal lithotypes. The coal images were collected from the pillar ribs with exposed surfaces in underground coal mines, and the coal lithotypes were identified when taking the images. The method of Gray-Level Co-Occurrence Matrix (GLCM) was used to analyze the textures of coal images of different lithotypes, and the texture parameters, such as contrast, homogeneity, energy, and entropy, were compared. The results show that the images of coal with different lithotypes have different textures, which can be quantified through the image processing. The results from this study demonstrate the potential of classifying coal lithotypes using rib photos and easing the data collection process of CPRR.

Feb 1, 2024

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By Francis Lucas

A microscope objective of given numerical aperture, whew used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability-the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise whew the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500, µµ and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.65 N. A. are wow an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Köhler and Dr. M. Vow Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 µµ which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 6, 1926

By Thomas S. Bishop

From time to time the mining engineer will be faced with the necessity of having to make a haulage study to determine not only the most suitable method of hauling material but also the most effective and economical type of equipment to use for his particular operation. Specifically, this chapter outlines a general description of various types of haulage units and their components, guidelines on the selection of equipment, material both operational and cost wise to be accumulated, discussions on the various factors involved in the development of the estimated production and cost analysis, examples of the above, and the necessary reference material. This material and examples are given in such a form as to permit the engineer to proceed on almost a step-by-step basis in the determination of the applicable haul speeds and other related portions of the haul cycle and resulting number of trips per hour. In recent years, the analytical methods used for the application of the various haulage units have undergone a considerable change. Several vehicle manufacturers and a few of the mining companies employ electronic digital computers to speed up the calculations and improve the accuracy of production estimating. The haulage computer program simulates the travel of the vehicle over the described haul roads by calculating incremental velocities, travel times, and travel distances from the known torque vs. speed characteristics of the vehicle. This is, in a sense, a numerical integration of the vehicle's performance and, of course, varies for each and every application. These travel times are then combined with easily estimated fixed times such as loading, turning and dumping, spotting, and any indicated delay times, resulting in a total cycle time for the vehicle. Usually, the travel times comprise the major portion of the time cycle; therefore, the concise computerized calculations eliminate much of the guess work in estimating vehicle productivity. Field studies have correlated this analysis

Jan 1, 1968

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Toshiyuki Nohira, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The electrochemical formation of Tb-Ni alloys was investigated in a molten LiCl–KCl–TbCl3 (0.50 mol% added) at 723 K. Open-circuit potentiometry was conducted using a Ni electrode after electrodepositing Tb metal at 0.20 V (vs. Li+/Li) for 300 s. There were four potential plateaus at (a) 0.66 V, (b) 0.80 V, (c) 0.95 V and (d) 1.56 V, respectively. Alloy samples were prepared by potentiostatic electrolysis at 0.60 and 0.70 V at 723 K. The alloy phase was identified as only TbNi2. Anodic dissolution of Tb from the formed TbNi2 was conducted at 0.90, 1.20 and 1.60 V, respectively. In the sample obtained at 0.90 V for 3 h, the existence of TbNi3 was identified by the XRD. Phase of the sample obtained at 1.20 V for 3 h was TbNi5. The sample obtained at 1.60 V for 3 h was Ni. Alloy samples were prepared by potentiostatic electrolysis at 0.50–0.80 V for 1 h using Ni plate cathodes in a molten LiCl–KCl containing TbCl3 (0.50 mol%) and NdCl3 (0.50 mol%). The highest mass ratio of Tb/Nd in the alloy sample was 56 at 0.70 V.

Mar 1, 2018

By Robert B. Sosman

ONE of the most neglected fields for physicochemical education as well as for research is that of high-temperature phenomena. Few universities or technical schools give instruction in the physical chemistry of substances at high temperatures. On the contrary such instruction is almost entirely confined to the region between the freezing and boiling points of water. This field should be extended to a much wider range of temperatures, both low and high. Such an extension is logical, sound, feasible, and practical.

Jan 1, 1943

By D. J. MacKinnon, Kazi E. Haque

Ammonia present in a variety of mine/mill waste waters was almost completely oxidized to nitrogen by chloride mediated electro-oxidation. A closed circuit operation of preconcentration of ammonia on a suitable adsorbent (e.g. zeolite or a resin) followed by brine stripping of ammonia and electrolysis of the strip liquor seems to have sound technical, economic and environmental merits. The removal of ammonia, cyanide, cyanate or thiocyanate from a mine/mill waste water (e.g. gold mill), either individually or collectively, is also feasible by chloride mediated electro-oxidation technique. Further R&D investigations are necessary for the development of a closed circuit operation for the removal of ammonia, cyanide and thiocyanate; and also to obtain technical data for process cost estimates

Jan 1, 1996

By D. L. McDanels, J. W. Weeton, R. W. Jech

An investigation was conducted to determine the stress-strain behavior and tensile properties of metallic composites and to relate them to the properties of the base materials. Tungsten fibers in a copper matrix were chosen as the model sys-tem to investigate these properties. Room-temp-atzcre tensile and dynamic -modulus tests were used To meet the demand for improved structural materials, considerable effort is being directed toward the creation of composite materials. One such material under investigation is the fiber-reinforced composite, in which a ductile, relatively weak matrix is reinforced with high-strength fibers. Some work has been done on the reinforcement of metallic matrices with metallic fibers1"5 as well as with ceramic-whisker reinforcement. Summaries of much of this work have been published by Mach-lin7 and Baske~.' Work done at the Lewis Research Center of NASA-" has involved the making and testing of composites composed of a fiber, tungsten, and a matrix, copper, which were insoluble in each other. An equation was presented that showed the relation between the ultimate tensile strength of the composites and the strengths and relative volume percents of the components. This relation was verified experimentally for composites containing fibers extending the full length of the specimen as well as for composites reinforced with short-length or discontinuous fibers. Since the publication of the preliminary results,9'10 additional data have been obtained. This paper presents these data as well as analyses of the stress-strain behavior and the mechanics of deformation of uni-axially oriented, fiber-reinforced metallic composites, in which both components are mutually insoluble. EXPERIMENTAL PROCEDURE Composites were made with high-purity copper as the matrix and 3-, 5-, and 7-mil-diam tungsten wire as the reinforcing fiber. Some specimens were made in which the reinforcing fiber extended completely through the full length of the composite test section. The fibers were placed in ceramic to determine these properties. The composites were reinforced with either continuous or discontinuos tungsten fibers. The tensile properties and stress-strain behavior of composites reinforced with either type of reinforcement were similar, and in both cases the full strength of the fiber was utilized. tubes to insure axial orientation and infiltrated with copper at 2200°F for 1 hr. Composites were also made with short-length (3/8 in. long) 5-mil-diam tungsten fibers as discontinuous reinforcement and infiltrated under the same conditions. The reinforcing fibers in both cases were longitudinally oriented in the direction parallel to the tensile axis. Room-temperature tensile tests were conducted on the composites, stress-strain curves were obtained, and ultimate tensile strength and elongation were measured. Dynamic modulus of elasticity, based upon the resonant frequency induced in the flexural mode of vibration, was also determined for the composites and the components. A more detailed discussion of the experimental procedure employed in this investigation may be found in Ref. 11. RESULTS Room-temperature tensile tests were conducted on 3-, 5-, and 7-mil-diam tungsten wires which had been annealed for 1 hr at 2200°F and show the tensile strength of the wires to be 331,000, 327,000, and 290,000 psi, respectively. Since all the composites were infiltrated under these conditions, the strengths were considered to represent the strength of the fibers in the composites throughout this study. The average tensile strength of the annealed copper used as the matrix in this investigation was 27,800 psi. Results of room-temperature tensile tests on composites reinforced with 3-, 5-, or 7-mil-diam tungsten fibers are plotted as functions of composition in Fig. 1. These data represent previously reported datag,l0 as well as data more recently obtained. The line shown on each curve represents a prediction of tensile strength as a function of composition; the calculation of this line was explained in Refs. 9 and 10. A similar plot is presented in Fig. l(d) for composites reinforced with short-length, discontinuous 5-mil-diam tungsten fibers. Again, both the previously reported and the recent data are presented, and the line shown is identical to that shown for

Jan 1, 1965

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

By Paul D. Merica, W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion The corrosion resistance of metals and alloys is never absolute and all-inclusive, a particular alloy will withstand some corrosive conditions well and fall utterly under others Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications One wants a soft, ductile sheet metal resistant to atmospheric corrosion, another, a high-strength alloy resistant to sulfuric acid The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less. than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935

By W B. Edgar, I M. Platten, C A. J Towsey, B W. Cuffley

The evaluation of historical goldfields has been common over the past 15 years, reflecting changing economic conditions, improvements in knowledge and technology and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins, which are structurally complex with an irregular distribution of gold, have variable geometry and architecture and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation, since it contributes to understanding the orebody, exploration target size and setting expectations. Mine records include documents such as plans, sections, reports, news cuttings, production tabulations, etc. A major advantage for the modern explorer is the capability of computer modelling to display this data in 3D. Historical records can give the explorer substantial information on various deposit characteristics, not least grade and geological continuity, geometry and architecture, mineralogy, metallurgical properties, bulk density and ground conditions. From an evaluation perspective, historical records can be used to support a Mineral Resource estimate, though its application will depend upon the quality and quantity of the data and judgement of the Competent Person. Effectively used, historical records can reduce geological uncertainty and focus evaluation efforts û thus reducing project risk.

Jan 1, 2009