Search Documents

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By Jianjun Tang, Wenjuan Bai

This paper presents a new method of formulation design for multi-component composite explosives. Based on the thermochemistry of the detonation process, the mathematic model of formulation design is established by optimization mathematics. Using the heat of detonation as target functions and taking the constraint conditions such as oxygen balance and costs etc into consideration, this model can provide an optimal solution quickly by means of personal computer. Using this method, the calculation and the simulation tests for a series of constituent sets and various constraint conditions can be conducted easily. In this way, the optimal formulation for the explosive can be determined, on the basis of the maximum heat of detonation and the lower cost.

Jan 1, 1997

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991

By Eric G. Zahl, John P. Dunford, Hamid Maleki

Coal bumps are influenced by geologic conditions, the geometric design of coal mine excavations, and the sequence and rate of extraction. Researchers from private industry and government agencies around the world have studied mechanisms of violent failure and have identified individual factors that contribute to coal bumps. To develop predictive tools for assessing coal bump potential, the authors initiated a comprehensive study using information from 25 case studies undertaken in U.S. mines. Multiple linear regression and numerical modeling analyses of geological and mining conditions were used to identify the most significant factors contributing to stress bumps in coal mines. Twenty-five factors were considered initially, including mechanical properties of strata, stress fields, face and pillar factors of safety, joint spacings, mining methods, and stress gradients. In situ strength was estimated in 12 coal seams where uniaxial compressive strength exceeded 2,000 psi. Allowances were made for favorable local yielding characteristics of mine roof and floor in reducing damage severity. Pillar and face factors of safety were calculated using displacement-discontinuity methods for specific geometries. This work identified the most important variables contributing to coal bumps. These are (1) mechanical properties of strata, including local yield characteristics of a mine roof and floor, (2) gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, which influence released energy,(4) stress gradients associated with the approach of mining to areas of higher stress concentrations, and (5) the mining method. By combining the strength of both analytical and statistical methods, new capabilities were developed for predicting coal bump potential and for building confidence intervals on expected damage.

Jan 5, 1999

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

INTRODUCTION Several major factors introduce uncertainties into the assessment of radon progeny exposure to miners using time-weighted average radon progeny concentrations: uncertainty in the measurement of radon progeny concentrations in specific areas, assignment of an individual miner's time to those areas, variation in radon progeny concentration between measurements and potential human errors involved in calculating concentrations and handling data. The currently available grab-sampling methods for determining working level were analyzed to determine the magnitude of the uncertainty due to each of these factors. For all measurement methods studied, the variation in the airborne concentration with time in operational areas of a mine is the dominant factor in the uncertainty in determining annual radon progeny exposures for individual miners. Uncertainties relating to accuracy of the method and precision of measurement were found to contribute a significantly greater portion of the total uncertainty than human errors. Under normal conditions, if the technicians performing the measurements are conscientious and well trained, human error contributes little to the total uncertainty of the radon progeny exposure determination. The primary goal of radiation monitoring is the reduction of radiation exposure to the lowest reasonably achievable level below regulatory limits. Monitoring personnel in mines should be trained not only to obtain accurate estimates of miner radiation exposures but also to recognize and, when possible, to implement correction of situations which result in unnecessarily high radon progeny exposures. ESTIMATION OF UNCERTAINTY DUE TO HUMAN ERRORS Human errors affecting the assignment of annual radon progeny exposure to individual miners can be placed in two categories: those related to the measurement of radon progeny concentration in specific mine areas and those related to estimation of occupancy time for individual miners and transcribing data to permanent records. The former are specific for the measurement method used; the latter are common to all methods. Errors in Determination of Working Level All systems for determining radon progeny concentration require measurement of several parameters, which include volume of air sampled, count rate and decay time. These quantities and appropriate constants are used in a basic equation, specific to the system, which estimates working level. An unintentional random mistake in measurement of any one of these parameters or in the selection of proper constants will contribute to the uncertainty in the determination of working level. In our analysis of human error we separated each measurement method into a sequence of independent operations, with each step subject to operator error. For each operation we estimated the probability of occurrence and the consequence of errors to obtain a resulting uncertainty. Certain types of errors result in specific consequences. For example, we assumed that an error of 5 seconds in timing of a 5-minute sample results in a fractional error of 1/60 (1.7%). Other types of errors can result in a range of uncertainty. Transposing digits read from a scaler can produce errors ranging from near zero to approximately 60%. In these cases we calculated the statistical variance for the distribution of errors. We assigned the square root of the variance divided by the mean as the consequence factor for that type of error. This is essentially the same as a coefficient of variation. The product of the probability of occurrence and the consequence factor is the fractional uncertainty in the measurement due to that particular error. The total uncertainty due to human errors is calculated by taking the square root of the sum of the squares of the uncertainties generated by all manual operations. Uncertainties Due to Human Error for the Kusnetz Method One of the techniques most commonly used to estimate working level in U.S. uranium mines is the Kusnetz method. A generalized way to express the equation used to compute WL by this method is: WL = (Net Alpha Counts)/(V)(ST)(CT)(E)(K) where: V = sample flow rate in liters/min ST = sampling time in min CT = counting time in minutes E = absolute counting efficiency K = Kusnetz conversion factor (dis/min-L per WL), as a function of decay time in minutes. The example of human error analysis presented here is based on the Kusnetz procedure having a timing sequence of 5 minutes sampling time, 40 minute decay time, 2 minute counting time. During the sampling procedure a stop watch is used to determine the timing interval. We assume that it is common to make small timing errors of a few seconds, but larger timing errors occur infrequently. Errors greater than 30 seconds are considered to be essentially non-existent since we assume that the

Jan 1, 1981

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By Kremena Dedelyanova

The paper presents research of mechanism for the creation of air bubbles in vibratory a column flotation machine. Factors are discussed that influence the increase in the duration of the bubble in the area of contact with the mineral particles. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in a vibratory column flotation machine is determined.

Aug 1, 2013

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By AIME AIME

THE sixteenth annual meeting of the Woman's Aux¬iliary, A. I. M. E., was held Tuesday morning, Feb. 16, at the Engineering Societies Building. The meeting was well attended, there being 99 registered from the metropolitan area and 78 from the sections throughout the United States. Mrs. Sharpless, the secretary, read the minutes of the annual meeting held a year ago, after which Mrs. Bassett, the president, gave her address of welcome. Mrs. Bassett said in part: "I would like, at this time, to welcome you all to this, our sixteenth annual meeting, and to express my appreciation to all the national officers and members of the board of directors for their loyal support and for the excellent work done by the chairmen of sections and their members. It is with much pleasure that I look back upon my visits with the sections in Washington, Arizona, Northern and Southern California, Chicago, Colorado, Western Pennsylvania and Utah before I assumed the office of president. During the last year I have much enjoyed meeting with the sections in Boston, Washington and New York. It is our duty to see that the achievement for 1932 be equal to that of the year that has just passed."

Jan 1, 1932

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

Education and Training for the minerals industry has been identified as one of the key priorities by the AusIMM and many closely related groups. The AusIMM Education Taskforce has been engaged, through a visioning exercise, in evaluating what minerals education and training should look like by 2025. A common recurring theme is that for minerals education and training to be efficient and effective into the future, it needs to be comprehensive and inclusive. Some previous attempts to achieve efficiency and effectiveness have had limited success, mainly due to approaching the issues involved from a narrow, singular perspective. This paper outlines that the achievement of the desired outcome may require an approach that parallels the same techniques that are used for multi-dimensional mine planning, treating tertiary minerals education and training in a similar way to the planning involved for a complex orebody. Just as efficient and effective mine planning requires engagement and understanding of many factors, so too does engagement with tertiary minerals education and training. The major factors that need to be considered are outlined in the paper, including: levels of tertiary education and training; Australian Qualifications Framework (AQF), Levels 1 to 13: systems of minerals education and training, such as higher education, (mainly universities), industry/professional associations and licencing requirements, vocational education, (mainly TAFE) and workplace programs; types of minerals or mining methods involved; volume of delivery; stage in the flow sheet, (geology, mining, beneficiation, extraction, refining). For comprehensive mine planning there is the need to develop links or roadways and openings between different levels of a mine. Similarly, to achieve a comprehensive tertiary minerals education and training model, there is a need to develop pathways, recognition and credit transfer between the various levels and components of minerals tertiary education and training.

Jan 1, 2005