Search Documents

By M. I. Kabir, R. S. Schechter, L. W. Lake

This paper presents the development and application of a novel scaling technique that, when used with a streamline model, causes a "bundle" of one-dimensional (1-D) problems to reduce to a single 1-D calculation. The 1-D bundle is the streamline representation of a two-dimensional (2-D) problem. The 1-D calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desktop calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the US Bureau of Mines.

Jan 1, 1986

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By F. M. Perkins, R. H. Jamison

Publications concerning scaling laws for laboratory flow models of oil reservoirs indicate that the relative permeability and capillary pressure relations must be the same functions of saturation in the model and its prototype. In this paper, the relative permeabilities and saturations are redefined in a way which permits one to have diflerent relative permeability and capillary pressure relations in the model and prototype. The development of the new scaling criteria is demonstrated by deriving scaling laws for one simple flow problem. INTRODUCTION The successful application of information gathered through bench-scale model studies to the prediction of multi-phase fluid flow behavior in petroleum reservoirs requires careful consideration of the scaling criteria. The requirements which must be met for a small-scale model to duplicate the behavior of a much larger reservoir prototype have been discussed by Leverett, et al,' Rapoport,2 and Geertsma, et al.3 According to these authors, the relative permeabilities to water, oil and gas and the dimensionless capillary pressures must be the must have the same values in the model and prototype. Furthermore, they point out that the viscosity ratios must have the same values in the model and prototype. In addition to these requirements, other scaling criteria are given which, when considered, usually dictate a much higher permeability in the model than exists in the reservoir. Since the more permeable model sands may have connate-water and residual oil saturations quite different from those in the prototype, the scaling requirements pertaining to the dependence of relative permeabilities and dimension l ess capillary pressures on saturation usually are not met. Also, if the model fluids are selected to give equal viscosity ratios in the model and prototype, one may find greatly different mobility ratios* in the two cases and, therefore, may expect grossly different flow patterns. For this reason, Craig, et al,' correlated the results of their model studies with mo- bility ratio rather than with viscosity ratio. As yet, however, no satisfactory method has been advanced which permits use of anything other than the scaling requirements outlined in the previously mentioned papers. The purpose of this paper is to present a method of developing a set of scaling criteria which permits different relationships between saturation and relative permeability or capillary pressure in the model and prototype. Rather than attempt to report scaling criteria for a variety of practical situations, this paper demonstrates by use of one simple example how the modified scaling criteria are derived.

By Barclay C, Jacobsen M, Towsey C

The Emperor Gold mine at Vatukoula, Fiji, is a nine million ounce gold telluride deposit. In January 1992, the mine was on the verge of closure when the current management team took charge. Losses had been incurred for two consecutive years and the published resource amounted to less than five years of production. Relationships with the workforce, the government and the general public were poor. Today, the mine has recorded three consecutive years of profit, has resources that will support the operation for at least 20 years and has excellent relationships with employees, government and the general public.

Jan 1, 1997

By L. Mercier, A. El-Hsaeri, L. Amaratunga

Laboratory scale studies of the development and application of high capacity heavy metal ion adsorbents with uniform nanoscale porosity (denoted MP-HMS, mercaptopropyl - hexagonal mesoporous structure) to extract gold from solutions is described. The adsorbents are selective towards gold ions. The adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 330-mg gold per gram adsorbent (up to 30% of their weight). Gold uptake by the adsorbent was found to increase dramatically with solution agitation. The adsorbent was found to be extremely effective in adsorbing gold ions from ultra- low concentrations, like those found in mine effluents. Experimental studies indicated that MP-HMS maximum adsorption of gold (99.9%) occurred under all solution concentrations. Another promising attribute of these materials is their favorable adsorption kinetics. The contact time required for 80% adsorption of gold was found to be less than 60 seconds. The efficiency of these nanoporous materials for the recovery of gold from mining effluent is evaluated and their prospect for application in the mining industry discussed. The process thus has the prospect of becoming an efficient and environmental friendly method to recover gold from aqueous solutions, such as gold mill effluents.

Jan 1, 2004

By Y Hansen, J Petrie

Life Cycle Assessment (LCA) is increasingly being used as a decision-support tool within mining and minerals processing and metals production. However, a number of initiatives have highlighted the current limitations of LCA to accurately reflect the environmental performance of minerals and metals. These programs include:the Mining, Minerals and Sustainable development project (Stewart, 2001); the United Nations Environment Programmme/Society for Environmental Toxicology and Chemistry (UNEP/SETAC) workshop on LCA and metals (NRCan, 2002); the UNEP SETAC Life Cycle Initiative; and the review of the existing ISO 14 040 set of environmental management standards. Together, these initiatives highlighted concerns relating to the ability of LCA to engage with and support metals recycling, to adequately reflect the impacts associated with products from a multi-product orebody, the ability to adequately reflect the toxicity potential of metals in the natural environment and the fact that resource depletion focuses on mining (and not consumption) as the depleting activity in the life cycle of a metal. Additional impact categories to be included in LCA were also suggested. In this paper we demonstrate how existing initiatives are addressing LCA limitations. Finally we present the state of the art in Life Cycle Impact Assessment (LCIA) for two impact categories:resource depletion; and impacted land footprint for solid wastes.

Jan 1, 2004

By V. L. Richards, S. N. Lekakh, S. A. Dutler

"This study presents determination on the thermal properties of investment casting shell molds used in casting process modeling. Superheat and latent heat from solidification and cooling of a casting can either be accumulated by ceramic shell for thin-walled casting or transfer to environment for massive casting. Heat capacity and thermal conductivity both play important roles in casting solidification. Thermal properties of ceramic shell depend on shell composition and fabrication techniques as well as thermal history during shell preparation process due to multiple phase transformations. Inverse modeling was combined with corrected Laser Flash method to determine the applicable thermal properties of the shell during casting solidification. Pure nickel was poured into ceramic shells containing two thermocouples and experimental cooling curves were obtained. These curves were then fitted to the model by adjusting temperature dependent heat capacity and thermal conductivity.IntroductionCasting solidification in investment casting shell affected by shell thermal properties including specific heat capacity and thermal conductivity. For relatively thin walled casting, most of the melt superheat and part of latent heat are accumulated by the shell. This process is mainly controlled by shell heat capacity. In the case of massive casting, significant part of latent heat transfers to environment through the shell so that this process is mainly controlled by shell thermal conductivity."

Jan 1, 2012

By D. J. Bryden, J. W. Oberholzer

In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has ex- pressed the desire for the development and testing of active on board suppression systems. As overseas systems cannot be used directly in the bord and pillar geometry it is necessary to adapt overseas and local technology to suit local mining conditions, as well as to test such developed systems for their compliance with the expressed needs. As the systems have to be tested in a specific roadway configuration, a facility was developed to enable the testing in South Africa. A surface test facility has been established which can be used to develop and test suppression systems on continuous miners and roadheaders. This facility consists of a tunnel wherein compliance tests can be conducted in simulated underground conditions. A number of methane explosion tests have been conducted in the test facility. The explosions conducted varied in CH,/air concentration (7,5 to 9 percent) and volume (26 to 88 m3). At lower concentrations there was a marked reduction in explosion strength and flame speed. Tests carried out with the Explostop system successfully suppressed the propagation of methane ignitions in both scenarios tested.

Jan 1, 1997

By D. Torrey

CONSIDERING the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By Gen-Hua Shi, Richard E. Goodman

In hard, discontinuous rocks, failure modes and stability are controlled to a great extent by the intersection of discontinuities with the excavated surface. We have solved the general problem of finding the shape and size of all blocks formed through the inter- section of any number of joints and excavation surfaces and will demonstrate a simple graphical method for determining which of these is the "keyblock." An example will explain this methodology applied to a simple open pit. The effects of slope curvature in plan or section, will be demonstrated. Finally, we will show how to determine the optimum orientations for the cut slopes. The methodology is based upon a powerful topologic theorem concerning the finiteness of spatial intersections. This paper is a companion to another dealing with underground openings in the Proceedings of the 22nd Symposium on Rock Mechanics (MIT) , July 1981. This paper discusses the rock blocks created by the intersection of discontinuities and excavation surfaces in a rock mass. It establishes principles and procedures by means of which those blocks that are finite and critically located can be identified and described. The main assumptions are the following: 1. The rock itself is assumed to be strong so that the only concern for stability is the movement of rock blocks them- selves.

Jan 1, 1983

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Richard Moldenke

AmonG the things that will always remain to the credit of the foundry-industry is the circumstance that nearly all the research-work of practical value in daily routine was done by active foundrymen, and the results were freely given by them to the world. Moreover, while consumers felt that to them was due a more systematic and exact method of work, the foundry-men again were the first to act in the establishment of specifications under which their product should be sold. To come to more recent times, the American Foundrymen's Association has not only made an elaborate series of tests on cast-iron, and adopted tentative specifications based upon them, but, in addition, it has urged the International Association for Testing Materials, through its American representatives, to make the testing and specification of cast-iron a distinct issue. The half-hearted support first granted was greatly augmented by the rapidly-growing recognition accorded to the enormous iron-casting industry; and when the president of the American Society for Testing Materials was instructed to ask for a special commission for this purpose, Europe was ready to cooperate. During the Buda-Pesth congress, at, which America was represented by Prof. Howe, Mr. Wood and myself, it was decided to add five members to the general committee on steel and iron, whose special duty should be to conserve the interests of the cast-iron branch of the industry. America took up the work at once, and enlarged its committee to 67 members, all of whom were actively concerned in the manufacture or study of cast-iron in all of its branches. At the organization-meeting in Philadelphia, April 25, 1903, Mr. Walter Wood was elected chairman, and myself secretary; and, within a week thereafter, the sub-committees were appointed and became active at once. The scope of the work was naturally limited to those branches of the iron-casting in-

Jan 1, 1905