Search Documents

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By Sylvan Z. Beer

The factors that determine the yield and crystal size in the two-temperature synthesis of A lp were examined. Low yields and small crystals were associated with low temperatures and pressure. Attempts to grow large crystals in the critical and supercritical region of phosphorus were unsuccessful. Crystal size increases markedly at elevated temperatures. Crystals grown at temperatures as high as 1450° C fluo-resced, under uv excitation, at energies close to the estimated band gap of about 2.4 ev, while crystals grown at lower temperatures tended to fluoresce in the red region of the spectrum. Those grown in the supercritical region showed no ALP fluorescence. Heating the high-temperature-grown ALP under vacuum greatly increased its fluorescence efficiency and moved the emission peak to higher energies. I HE III-V compounds, with few exceptions, have been prepared by the two-temperature method. In its classic form this technique is applicable to closed systems where at least one of the components, in this case the column V element, is a liquid or a solid with a high vapor pressure. One advantage of this method over flow systems is in its simplicity. In addition, because it is a closed system, it can, under the circumstances to be described later, be run at higher pressures of the volatile species than in flow systems. In instances where the III-V compound is soluble in the parent III metal to about 1 mol pct or higher, solution growth can be made to take place by slow cooling. This, for instance, is one way in which single-crystal GaP1 and Inp2 have been grown. Initial attempts to synthesize and grow A1P by this technique were not too successful; the yield was low and the crystals obtained were exceedingly small. The conditions required for improving the yield and growth by this technique were, therefore, sought. Two obvious conditions which could be controlling were examined. These were the temperature of the aluminum and the pressure of the phosphorus. The range of temperatures studied extended from about the melting point of aluminum, 660° to about 1450°C. The latter is dictated by the vapor pressure of aluminum which reaches about 1 Torr at that temperature and the limitations of the materials of construction as described in the next section. The pressure range of interest covers from below 1 atm to above the critical pressure of phosphorus, 82.2 atm. EXPERIMENTAL The Temperature of Aluminum as a Variable. A series of experiments were run in the conventional two-temperature manner. All refractories and quartz were dried by heating at 800° to 900° for a minimum of 24 hr, and usually much longer, before use. The aluminum

Jan 1, 1969

By K. L. Whitehead

An examination of 60 mines, 11 illumination hardware manufacturers, and Q mobile face-equipment manufacturers was conducted to determine the state of the art of mine-illumination hardware, define lighting system installation and maintenance problems, and assess personnel acceptance of lighting. Longwall and mobile face-machine illumination were studied. Major problems on room and pillar installations include damage of exposed components, electrical failures, and reduced lamp life, with extreme variability in the degree of these problems. Most longwall systems had low or moderate maintenance requirements, cable damage being the most significant problem. Most mobile face-equipment operators liked their machines' lighting systems, but many complained of glare and other problems. Longwall lighting was unanimously accepted by face personnel, and most complaints were minor. Based on the survey, general installation and maintenance guidelines have been established, addressing hardware design aspects, approaches proved effective to minimize problems, and improper practices noted which are detrimental to effective lighting.

Jan 1, 1981

By Warren W. Jamar, Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron informatior]mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were reopened pasttwoyears,and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties. During 1949, the largest mine in Iron County shipped 571,287 tons, and one of the newer mines shipped 39,378 tons, with a range total to 3,535,-373 tons. Since the Menominee Range was opened in the 1870's, the mines in Iron County have shipped 85,890,922 tons. From an operator's viewpoint rather than a geologist's, the ore is' classified as semi-hard, composed of hematite and limonite. It is not as soft as the ores of the Marquette Range nor is it as hard as the hard ores of the Marquette and Vermillion Ranges. The ore bodies have slate hanging walls and slate footwalls. In most cases the hanging walls and footwalls are soft and high in sulphur. The sulphur comes from pyrite, and these slates will ignite when piled more than 6 to 8 ft high. Ore is mined on this range by: 1—Sub-level stop-ing; 2—Shrinkage stoping; 3—Sub-level caving; 4— Block caving; 5—Top slicing. The predominance of these methods is in the order named. Underground drilling is important in the mining cycle. Some changes made and trends toward future changes fall into four categories: Drill bits, drill steel, drill machines, and compressed air pressures. Several types of bits have been tried and are in use. They include the detachable tungsten carbide, insert bit; the intraset steel bit, which is a conventional steel rod with tungsten carbide insert; the one-use bit; and the multiple-use bit. For many years, detachable multiple-use bits have been standard. In tests conducted recently to im- prove drilling efficiency, this bit was used as the basis for comparison. Under existing conditions, a multiple-use bit can be resharpened about three times before it is discarded. A thorough test of 2-in. tungsten carbide threaded bits was conducted under various ground conditions. 1—The drilled footage ranged from 48 to 600 ft per bit; averaging 357 ft per bit. Under these same conditions, a multiple-use bit ranged from 8 to 80 ft per bit. 2—The bit cost was greater for the insert bit in each case. 3—The average drilling speed for the insert bit was 12 in. in 62 sec and for the multiple-use bit was 12 in. in 64 sec. In a second test, 2V4 -in. tungsten carbide bits with the large 1 3/16-in. thread were used in moderately soft ground on a 152-lb drifting drill on a long feed jumbo. 1—The drilled footage ranged from 450 to 5000 ft per bit, averaging 1810 ft per bit. Under these same conditions, a multiple-use bit averaged 64 ft per bit. 2—The bit cost was reduced by the use of the insert bit. 3—No increase in drilling speed was recorded. 4—Minimum footage obtained was caused by thread failure. To improve the thread life, thread size on the rod was increased and the bit was attached to the rod with a pipe wrench. After this, bits failed in equal proportions because of cracked skirts, broken inserts, and gage loss. Tungsten carbide bits are now used in the operation where this second test was conducted because labor costs were lowered as a result of reducing the number of bits being changed by the miners. At the same operation and under the same conditions as the second test, 1Y4-in. insert bits with standard 1-in. threads were used. These bits did not drill much more than 300 ft before thread failure and were then welded to the rods and used until total failure. Sometimes this footage was considerable, sometimes it was not. Chisel-type 2%-in. insert bits were

Jan 1, 1952

By W. D. Maier, H. V. Eales

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. A lithological and geochemical study revealed significant lateral variation of the interval over 170 km of strike, from about 30 m at the Union Section to 220 m near Brits. The cumulates also become more evolved and leucocratic with distance from the Union Section both towards the NE (Amandelbult) and SE (Impala, Rustenburg and Brits). It is inferred that the persistent heat flux from a putative major feeder zone near the Union Section impaired deposition of felsic cumulates in the vicinity, delaying crystallisation of successive phases in parts of the chamber near the feeder. New influxes were therefore deposited on a footwall of varying thickness and lithology in response to different degrees of crystallisation and accumulation along strike. The development of cyclic units of chromitite, harzburgite, pyroxenite, norite and anorthosite was interrupted at different stages in different parts of the chamber

Apr 1, 1994

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By J. A. M. van Liempt

SINCE the discovery of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystalline metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state METHOD A 1. Tammann's Method. 1-Tammann succeeded in making bismuth single crystals of a maximum length of 20 cm. by undercooling the molten metal 0.1 to 0.3° G. below its melting point in glass tubes of a maximum

Jan 1, 1928

By Donald A. Dahlstrom

If you have ever driven on the Autobahns of Western Germany, you are well acquainted with the "fast lane." There is no speed limit; there are only two lanes in the direction you are going, and if you choose to drive in the fast lane, you had better be prepared to drive faster than anyone or someone will tailgate you with a constant screeching horn until you move to the "slow lane." The prize for this mastery of the fast lane is some kind of a "macho" feeling and getting to your destination sooner than your competitor. This has some comparisons with today Is liquid-sol id separation. We've certainly had our moments in the fast lane but we've also had other countries forcing us into the slow lane at times. It can be very embarassing when someone almost runs over your back and then shakes a fist at you as you shakily scatter to the much slower and overcrowded lane. Because of necessity, there will be many new improvements and added requirements in the next decades into the 21st century and beyond. Those countries and industries that can maintain the pace in the fast lane will be successful while the others may well be relegated to the non-competitive lane. Before considering what will be the challenges in the future for competitive liquid-sol id separation performance, it would be wise to review progress over the past forty years in this area. The author has to admit his ancient age and believes he can act as an evaluator of these many advances. To place the beginning of the 40 years (the author predates his initiation into liquid-sol id separation by one more year), the United States was still building smelters and operating them with little or no sulphur dioxide removal , practically

Jan 1, 1989

By J. A. M. van Liempt

Since the discovery of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state Method A 1. Tamwmnn's Method1—Tammann succeeded in making bismuth single crystals of a maximum length of 20 cm. by undercooling the molten metal 0.1 to 0.3' G. below its melting point in glass tubes of a maximum

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By E. V. Murphree

CREATION of atomic energy, aside from its influence on war or peace, has posed these basic questions for the world: How soon can energy from atoms be harnessed to do man's daily work? How much of this power will there be, to what degree will it supplant present fuels, and what does it imply for the future of civilization? Answers to these questions may be found in part in analysis of just what atomic energy is and how far its development has come. The answers are encouraging. One of the first questions encountered in considering the application of atomic reactions is whether such reactions can be controlled. Fortunately, this has been adequately demonstrated by the operation of the Government plutonium plants at Hanford, Wash. Here nuclear reactions are carried out on a large scale involving liberation of about a billion B.t.u. per hour. This hourly heat liberation is equivalent to that obtained from about 7100 gallons of fuel oil. It has been possible to operate these plants day in and day out with the reaction controlled at the intensity desired. There should therefore be no question that, under proper conditions, reactions involving nuclear fission can be controlled.

Jan 1, 1946

By Francis P. Sinn

IN the zinc smelting industry the year 1947 seems to have been one of putting one's house in order rather than one of any material technical development or radical change in operating conditions. Labor generally has been in better supply but several plants report a scarcity of skilled workmen. Some plants continue to operate on the basis of a six-day week and will probably continue to do so until labor is more plentiful. Only one plant is known to have operated on a curtailed basis because of labor shortage, but here the difficulty was lack of proper housing facilities. Necessary materials and equipment for much-needed maintenance and modernization have been in short supply so these programs have often been delayed. Laborsaving devices of the "Payloader" type have been more generally used for handling materials. Slab zinc production was discontinued during the last months of the year at Danville, 111. and at Langeloth, Pa. Both of these plants used the Hegeler type of furnaces fired with producer gas. It is understood that the rolling mill and possibly the acid plant at Danville will continue to operate. At Langeloth acid will be produced from

Jan 1, 1948

By A. E. Michon

My comments today are directed toward western coal and its impact on Burlington Northern. I will be discussing three major topics. These are: location and extent of mining activities, the flows of this coal traffic into the various market territories, and finally the interaction of this western coal with coals found in the balance of the United States. When we at BN speak of western coal, we refer to those substantial deposits lying in southeastern Montana and north-eastern Wyoming. This territory covers many different coal formations. For the sake of simplicity, I will be referring to this general area as the Powder River Basin (or the "western" coal fields). This slide highlights the area overlayed by a map of the BN rail system. The U.S. Bureau of Mines estimates the demonstrated reserve base of Montana and Wyoming to be approximately 176 billion tons. Of this figure, about 73 billion tons is minable by surface methods. This is roughly 72% of the total strippable reserves in the western united states, BN does not have sole access to this coal for there are deposits in southern Wyoming near the union pacific railroad. I will say more about this later.

Jan 1, 1978

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974