Search Documents

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

Smarter Gravity Separation Using the Kelsey Centrifugal Jig With relatively coarse grained and easy-to-process ore sources rapidly dwindling, smarter techniques are becoming more necessary for the continued success of mineral processing operations, while increasing environmental pressures also require more environmentally friendly solutions. Gravity concentration has long been employed to pre-concentrate minerals using water, reducing or eliminating the need for less environmentally friendly processing techniques such as flotation. Conventional gravity recovery devices however, operate in a 1 g environment with limited efficiency in the separation of fine particles of heavy and gangue minerals. More recently developed centrifugal concentrators operate in a multi-g environment and enable finer heavy minerals to be recovered, but also exhibit limited separation efficiency due to the separations being based on solid particle mass differentials. Further enhancement of gravity separation has been achieved using the Kelsey Centrifugal Jig (KCJ), which also operates in a multi-g environment, but separates minerals on the basis of specific gravity differentials, using 'ragging' media and a pulsation mechanism, which maximises the effect of differential particle accelerations. This enables the efficient separation/recovery of minerals down to a particle size of ~6 ¦m and/or separation of minerals with a low specific gravity differential. This paper presents details on the principals of operation of the KCJ, recent improvements in the technology and recent developments in modular KCJ plants, as well as some KCJ application areas, which offer smarter, environmentally friendly processing opportunities for the mineral processing industry.

Sep 13, 2010

By Erwin H. Leeman, Raymond R. Rice, Gerald L. Hassler

In the past few years a great deal of preeise information has been obtained about the relation of natural gas to oil production1. The improvement of our understanding has been of great value, both in prolonging the life of wells and in providing a much needed technical background for the legal problem of proration. But there are two principal aspects of the problem of production. It is necessary to consider not only the energy available, in the form of compressed and dissolved gas and in the pressure of driving water, but also the tenacity with which the sandstone holds the oil. The amount of oil that each sand condition will produce under given conditions of gas content should be determined. Hitherto the effect of the sand has been judged by a study of the flow of each well coupled with a procedure for extrapolating the production curve; hut, as is well known to evaluation engineers, such production curves are subject to changes that are not well understood, and often are affected by outside disturbances. On the whole, the concept of "potential production" is vague principally because the influence of the sand in production is not known beyond the simple ideas of porosity and permeability. The permeability is a quantity that has only inference value where mixtures of gas and oil or of gas, oil and water are present. Excellent studies of the production of oil from reservoirs packed with unconsolidatcd sand are available2, but these studies treat largely of small-scale analogzes to a producing field, and the conclusions to be derived from them arc necessarily of a qualitative character because it is not known in what way these miniature oil fields resemble large ones.

Jan 1, 1936

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By Joseph S. Malesky

As essential as the discovery of coal was to our state of advancement, the discovery and development of explosives marks one of the most important findings in the history of civilization. For this reason explosives are rightfully referred to as the forerunner of progress. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. An explosive may be defined as a substance (usually a mixture) that, where flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1973

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers' Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil to be extracted, and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled; had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers' Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be. produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent. interest additional during the life of the property.

Jan 2, 1918

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By P Mackenzie, S Askraba

Pyritic black shales present several challenges to mining operations due to their reactivity. The risk of predetonation of explosives in blastholes, spontaneous combustion of fractured rock and the generation of acid rock drainage must be managed for safety, operational and environmental reasons. At the Mt Tom Price iron ore mine there is a need to differentiate between reactive and non-reactive shale in order to assess risk and make decisions on materials handling. The current approach uses a combination of stratigraphic information and sulfur analysis of blasthole samples. The time taken for sulfur analyses can be a constraining factor on mine production. A new instrument developed by ANSTO Minerals overcomes some of the current limitations on material characterisation. The IOR MeterÖ measures the intrinsic oxidation rate (IOR) of samples of broken rock by circulating air through a sample and monitoring the oxygen concentration over time. The intrinsic oxidation rate is given by the rate at which oxygen is consumed per unit mass of sample, in units of kg(oxygen) kg-1(sample) s-1. Up to eight samples can be measured simultaneously and the turn-around time can be less than 12 hours. Initial trials of the IOR MeterÖ were undertaken at the Mt Tom Price mine in July 2004. The measured IOR of samples from a blasthole pattern spanning different geological layers containing black shale, correlated strongly with the expected reactivity of those layers. The correlation between position in the geological sequence (detailed stratigraphy) and IOR MeterÖ results were much stronger than that between stratigraphy and sulfur content. The new characterisation technique offers the prospect of improving the ability to identify and predict the behaviour of reactive black shales and to differentiate more precisely between different materials. Mine planning, operations, safety and environment all stand to benefit from the success of further trials of the technique.

Jan 1, 2005

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004

By Erwin H. Leeman, Raymond R. Rice, Gerald L. Hassler

In the past few years a great deal of preeise information has been obtained about the relation of natural gas to oil production1. The improvement of our understanding has been of great value, both in prolonging the life of wells and in providing a much needed technical background for the legal problem of proration. But there are two principal aspects of the problem of production. It is necessary to consider not only the energy available, in the form of compressed and dissolved gas and in the pressure of driving water, but also the tenacity with which the sandstone holds the oil. The amount of oil that each sand condition will produce under given conditions of gas content should be determined. Hitherto the effect of the sand has been judged by a study of the flow of each well coupled with a procedure for extrapolating the production curve; hut, as is well known to evaluation engineers, such production curves are subject to changes that are not well understood, and often are affected by outside disturbances. On the whole, the concept of "potential production" is vague principally because the influence of the sand in production is not known beyond the simple ideas of porosity and permeability. The permeability is a quantity that has only inference value where mixtures of gas and oil or of gas, oil and water are present. Excellent studies of the production of oil from reservoirs packed with unconsolidatcd sand are available2, but these studies treat largely of small-scale analogzes to a producing field, and the conclusions to be derived from them arc necessarily of a qualitative character because it is not known in what way these miniature oil fields resemble large ones.

Jan 1, 1936

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In L947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at Present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act. Coal mining in Alaska has been handicapped by an inadequate supply of dependable workers. Wage scales have been very high in recent years, and "floaters" have been attracted to the coal mines. This type of labor is not conducive to efficient operation. Modernization of mines will require skilled and dependable workers and to induce such men to become interested in coal mining in Alaska, modern facilities, such as modern houses, schools, churches, and recreation halls, must be provided near the mines. Alaska is still a frontier and improvements in living standards must accompany development of mines in order that a stable community may be established. Coal is known to have been mined in Alaska at Port Graham, on Cook Inlet, by the Russians in 1854. During the Klondike gold rush in 1898, coal was mined in scattered areas for use on steamers plying the Yukon River and its navigable tributaries. After the Alaska Railroad was built, two important fields were developed—the Nenana and the Matanuska (Fig 1). The Bering River field was explored by the Guggenheim interests at one time, and a railroad to the area was constructed. However, the field was abandoned because of litigation and reported unsatisfactory physical condition of the beds. There are areas that today are unimportant but which may be developed in the future. Possibly the most important of these is the deposits of subbituminous coal adjacent to Cook Inlet, near Homer, on the Kenai Peninsula (see Fig 1). It is expected that the demand for coal in the Kenai Peninsula will increase because the population in that area has increased as a result of agricultural development. Numerous outcrops of coal are exposed on the peninsula and development of a mine there would obviate dependence on supplies of coal from the Matanuska field. Coal from this field must be shipped approximately 160 miles by rail to Seward and transported thence by boat about 180 miles to Homer. There has been no regular boat service from Anchorage to Homer. There are deposits of coal in the Arctic region but a description of them will not be given in this paper, which will describe the more important deposits in the Alaska Railroad belt. The results of a reconnaissance in the Arctic have been described.' Description of Fields MATANUSKA FIELD The Matanuska field lies in the valleys of the Matanuska River and its tributaries and their separating ridges. This field has been interpreted by geologists as a sunken fault block that separated the Talkeetna Range of mountains from the Chugach Range. The Matanuska River flows west along the south side of the field and the Glenn highway, which extends from Anchorage via Palmer to the Richardson highway near Glen Allan, follows the Matanuska Valley. This road to the coal field can be traveled the year around. Although the snow-

Jan 1, 1950

By J. Chipman, N. J. Grant, E. C. Roberts

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-Si02-FeO-Cr& type in the temperature range 1526' to 1734OC. The effects of slag oxidation, temperature, and basicity were observed. IN spite of the fact that chromium is one of the most important alloying elements in steel, and exists in almost all steels as a significant residual element, little research has been done to determine its behavior in basic steelmaking processes. Considerably more work has been done under silica-saturated acid slag conditions. Korber and Oelsen,' Herasymenko,' and others have generally agreed that in acid steelmaking practice the chromium in the slag behaved as if it were present as the chrom-ous ion (CrO). Work by Hilty- ir, high chromium slags also indicated that chromium may exist as CrO. In basic slag systems no equilibrium data exist. Based on individual studies of basic open hearth and electric furnace practice, Bardenheuer," Rock-rohr,% nd HauckQ oncluded that: 1—chromium recovery increased with decreasing basicity, and 2— chromium recovery increased with increasing temperature, although the effect was small. In similar studies Yavioskii and Dzemyen' concluded that: 1— slag FeO is the most important variable, 2—the basicity of the slag has no effect on chromium recovery, and 3—slag viscosity is not high even when 20 pct Cr,O, is present. Lapitskii\ oncluded that chromium recovery improved as the basicity of the slag decreased and increased with increasing manganese in the metal. Regarding the effectiveness of CrZ08 as a base or acid in basic slags, both Kristofferseno and Trojer" reported that Cr,08 was an acidic component requiring neutralization as 2CaO-Cr,O,. Experimental Procedure The experimental apparatus and procedure used for the present research were similar in most details to those used by Winkler and Chipman" and were described in detail by them. A magnesia crucible was used, holding 60 to 80 lb of Armco iron which was decarburized with hydrogen to about 0.010 pct C. Since all the metal samples solidified without gas evolution, this carbon level was assumed not to be significant. Synthetic slags made by mixing pure oxides were used throughout the study. Temperatures were measured by means of calibrated W-Mo thermocouples and were checked by Pt-Pt-Rh thermocouples. The range of temperatures covered in this study was from 1526" to 1734°C. The chromium content of the iron was in the range 0.032 to 0.82 pct, although the bulk of the tests showed 0.04 to 0.2 pct. The slags were of the CaO(MgO)-SiO,-FeO-Cr,O, type in which the Cr,O, content was from about 2 to 20 pct, although most of the slags showed from about 2 to 10 pct. The FeO range was from about 10 to 65 pct. CaO and SiO, were in the range of about 5 to 45 pct each, yielding a rather wide range of basicity values. The first 12 heats were made without a sulphur addition, and with only 30 min allowed for slag-metal equilibrium to be reached. In previous research it had been shown that less than 30 min was adequate to achieve equilibrium in slags free of Cr2O8.11,14.15 A study of the present data indicated that some of the tests may not have reached equilibrium in this time; accordingly four additional heats were made in which at least 1 hr was permitted for equilibrium to be reached. For reaching

Jan 1, 1955

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By S. Soren, K. Deo Mehta, G. Jha

The paper aims to find a sustainable sintering process through cleaner means, in order to achieve the desired outputs with zero environmental impact. At present, sintering has no control over its environmental impacts. These impacts occur when fossil fuels such as coal and coke are used in metallurgical sintering. These fossil fuels are undoubtedly effective in their assigned reducing task, but simultaneously emit about 220 kg of GHGs (greenhouse gases) per tonne of sinter produced. The current attempt has focused on reducing these emission levels by switching from coke to a renewable fuel source such as biomass. Biomass is a cleaner fuel source with a significantly lower emission footprint compared to coke. In the experimental campaign, sawdust and wood-charcoal were used in substitution for coke. Experiments were designed in a progressing substitution to obtain the maximum substitution ability without compromising the sinter properties. Sawdust as raw biomass source optimally substituted 10% of coke. The substitution levels were remarkably higher (30%) for wood charcoal due to its low moisture and high calorific values. A fuel blend with 30% biomass and remaining coke succeeded in producing a sinter with acceptable quality indices. Sinters prepared with or without biomass contribution shared an identical phase transformation and microstructures. In order to to maintain consistency in the process, every effort was made to maintain all operational and process parameters identically, except for the fuelling framework. Keywords: Sintering, sustainable, biomass, GHGs, fuel substitution

Jan 1, 2020

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Scott Tzcrner

WITHIN recent years people have begun to realize the importance and significance of the mining and allied industries. The leading part the engineer plays in civilization is becoming recognized. However accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business. It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization, but on the whole, the magnitude of the-industry is underestimated. In this paper I shall call attention briefly to the importance of mining in the United States, in Canada, and in the world. Ordinarily, the annual primary mineral production of the United States is about $5,500,000,000. The average for the last 5 years has been a little over that, but last year, sadly enough, it was less than 31/4 billion. Just now, we are on the decline, and have been for the last two years. In Canada, the 5-year average was about $268,000,000, and last year it was 227 million. Due in part to gold mines (in 1930, for the first time, Canada's gold production exceeded that of the United States), the Canadian average is holding up better than ours. Average world mineral production over the last -5 years has been estimated at about $12,000,000;000 whereas in 1931 it was less than than 8 billion.

Jan 1, 1932

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By V. Baltazar

The behaviour of arsenic and antimony during copper electrorefining was studied in order to identify the conditions under which good quality copper cathodes could be produced from anodes with high levels of these impurities. Examination of the effect of current density over the range 21 to 37 mA/cm2 indicated that the relative amounts of As and Sb entering the electrolyte affected the onset of passivation. When the ratio of As/Sb entering the electrolyte was greater than 2, the anodes showed no sign of passivation even at the highest current density; when the ratio was less than 2, the anodes passivated at 37 mA/cm2. Cathode analyses showed that anodes with an As/Sb dissolution ratio less than 2.0 tend to produce cathodes of inferior quality even at normal current densities (25.7 mA/cm2). The criterion of a minimum As/Sb dissolution ratio of 2.0, and mathematical correlations for the distribution of As and Sb between the electrolyte and slime developed in a previous study, allow the calculation of the maximum allowable Sb level in en anode for a given As concentration. Analyses of plant data at the CCR Division of Noranda Inc. for the last four years of operation have demonstrated that the use of this as a quality control tool has allowed the quality of copper cathodes to be maintained despite a significant increase in the average Sb levels in anode receipts.

Jan 1, 1987