Search Documents

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By James C. Sever

The mode of operation of dolomite kilns at a magnesium reduction plant using the Magnatherm process was designed to minimize operation cost and maximize kiln refractory life. Analysis of downstream operation issues shows the quality metric for dolime changed from loss on ignition to specific surface area. This produced a complete change in kiln operation; the net results being major plant productivity increases decrease in operating cost, and increases in both kiln operating costs and reline frequency.

Jan 1, 2015

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980&apos;s, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014

By Kathleen Kreiss, A. James Ruttenber

INTRODUCTION Early in the morning of July 16, 1979, there was a breach in the earthen retaining dam of a tailings pond at the United Nuclear Corporation&apos;s (UNC&apos;s) Church Rock uranium mill. The acidified liquid and tailings slurry spilled through the damaged portion of the retaining wall into an arroyo that is a tributary to the Rio Puerco river system. The Rio Puerco runs through Gallup, New Mexico, and eventually crosses the New Mexico-Arizona border (Fig. 1). On its way to Gallup, the Rio Puerco and its tributaries pass through land with a checkerboard pattern of ownership, with portions owned or leased by the Navajos, individuals, the Bureau of Land Management, and the State. In terms of tailings liquid volume (3.6 x 108L; 94 million gal), the UNC spill ranks as one of the largest. The mass of solids released in the slurry (10.0 x 105 kg; 1 100 tons) appears to be close to the median for accidents of this kind, however [U.S. Nuclear Regulatory Commission (NRC), 1979]. The UNC first opened its Church Rock uranium mill in 1977 on land adjacent to acreage belonging to the Navajo tribe. The mill, which is next to the UNC Church Rock mine, is located approximately 16 km (10 miles) northeast of Gallup, New Mexico (Fig. 1). Gallup, a town of 18 000 people, is the closest population center. The region surrounding the plant site is sparsely populated by Navajos, at a density of approximately 5.8 persons/km2 (15 persons/sq mile). The UNC mill and mines employ approximately 650 persons, and the adjacent Kerr-McGee uranium mine employs about 300. The UNC mill normally processes 3.2 x 106kg/day (3 500 tons/day) of uranium ore, depositing the acidified tailings slurry in a series of three earthen holding ponds. The tailings ponds are located east of the pipeline arroyo that feeds into the Rio Puerco approximately 2.4 km (1.5 miles) from the southernmost tailings dam. The liquid portion of the tailings slurry evaporates in the ponds; hence, under normal conditions, there is no surface flow from the holding ponds to the arroyo. Both runoff from the plant site after heavy rains and possible seepage from the tailings ponds may deliver radionuclides to the arroyo-river system, however. The dam across the southernmost tailings pond was considered to be in keeping with the state of the art. However, the New Mexico Environmental Improvement Division (NMEID) had warned UNC about dangers of locating the pond over a heterogeneous geological formation. The state Engineer&apos;s Office approved of the site only after UNC agreed to strict design criteria. Others have pointed to dangers of constructing earthen dams for impoundment of uranium mill tailings (Carter, 1978). Causes of the dam break were multiple: the UNC mill filled the tailings pond to a level that exceeded permit criteria; the tailings pond was lined improperly; the dam was constructed using clay that was compacted excessively, resulting in cracking and subsequent seepage; and the unstable substrate beneath the dam permitted differential settling. The UNC Church Rock mine has continuously released dewatering effluent into the pipeline arroyo at a rate of 88.3 L/sec (1 400 gal/min) since 1968. Before 1975 this effluent was not treated; after 1975 it received precipitation treatment for removal of Ra-226. Radionuclides are also released into the river system through the dewatering of the Kerr-McGee uranium mine 1.6 km (1.0 mile) north of the UNC mill. During usual mining operations, approximately 227 L/sec (3 600 gal/min) are released into the pipeline arroyo and subsequently into the Rio Puerco. The Kerr-McGee mine began continuous release of dewatering effluent in January 1972. In 1974 Kerr-McGee began Ra-226 precipitation treatment of its dewatering releases, but NMEID data indicate that treatment has often been incomplete. The effluent from both mines has been responsible for transforming the downstream portion of the Rio Puerco from a sporadically dry riverbed into a continuously flowing stream and has contributed to the current levels of background radiation along the river system (Table 1). This paper will summarize the postspill monitoring efforts and relate the assessment of this spill to the general question of evaluating the health effects of nuclear fuel-cycle wastes. The data pertaining to the measurement of radionuclides in the Church Rock environment and the radionuclide concentrations in animals will appear in forthcoming reports. CHURCH ROCK HEALTH EFFECTS ASSESSMENT APPROACH The initial health effects evaluation involved identifying the radionuclides that were released into the river system from the tailings pond. Table 1 lists the State of New Mexico maximum permissible radionuclide concentrations for liquids released to unrestricted areas, the typical tailings liquid concentrations, and postspill river water concentrations. The tailings liquid contained comparatively high levels of Th-230, Ra-226, Pb-210, and Po-210--all of which, according to postspill river water samples, had exceeded the state maximum permissible concentrations (MPC) at one time or another. After the radionuclides in the tailings were identified, pathways through which humans could be exposed were clarified. Environmental monitoring data were then used to quantify the important pathways of human exposure. Water samples were collected from the river, from test wells dug near

Jan 1, 1981

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk&apos;s axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem&apos; in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By Henry E. Keniston

In every business today costs come under almost microscopic scrutiny. It&apos;s hard to conceive that less than 30 years ago there was no such cost consciousness apparent in overall industry. Railroads, through their almost absolute monopoly on freight handling, were one of the industries where little thought was given to overall costs. True regulation kept rates in line, but railroads did very little in the area of supplying equipment intended to help the shipper minimize his costs and at the same time result in savings to the rail carrier. During this period, except for isolated cases, railroads placed standard cars for loading. Most railroad car fleets consisted of box cars, hopper cars, flat cars and low side gondola cars certain roads having unique movements developed special cars to accommodate the particular product, but seldom did these cars move in general interchange service. Most of you are aware that several large companies built railroads of their own as an integral part of raw materials handling from remote sources to production plants located near concentrations of usage. On these railroads special cars were built with little thought to inter-change service. Examples of such railroads are the Duluth, Missabe and Iron Range, the Elgin, Joliet and Eastern, the Union Railroad, the Bessemer and Lake Erie and the Birmingham Southern.

Jan 1, 1972

By A Annor, L J. Chen

The production of paste backfill has typically been accomplished through the adaptation of existing technology. Thickeners and disc filters have several drawbacks when applied to production of tailings paste backfill. Personnel at CANMETÆs backfill research laboratory in Sudbury, Ontario, Canada have been carrying out research into and development of methods to produce paste backfill using total mill tailings since 1991. Using a silo for production of paste is not a new concept but has been refined to a marketable level. This technology is based on a fluidization principle that assists in settling the tailings to an homogenous state in a silo. Other developments include patented de-watering technology for use in the silo to speed the settling of the solids to a suitable solids content, optimisation of silo geometry, and instrumentation related to paste backfill production and transportation. The advantages to fluidisation technology are in reduced capital cost, reduced operating costs and in the environmental benefits of using full plant tailings over classified tailings or alluvial aggregates. Another major advantage is in the ability of this technology to be retrofitted to existing hydraulic backfill plants to further reduce capital cost. This paper details the development of the new technology as well as the associated cost savings over other technologies. It will also look at the research and development of unique components that make this technology work.

Jan 1, 1998

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime&apos;s shares and manages and operates the mine on Prime&apos;s behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts&apos; administration.

Jan 1, 1999

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology&apos;s development.

Jan 1, 1999

By M. P. Juszli

During the 1980&apos;s, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being trans-ported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to far-away customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable Just a few years ago.

Jan 1, 1989

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne&apos;s Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth&apos;s crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature&apos;s materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man&apos;s use of horn, another substance with peculiar properties of roughness in all directions without the &apos;grain&apos; of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988