Search Documents

By B. K. Belle

The use of diesel engine locomotives in South African mines can be traced to Van Dyk Consolidated Mines Ltd on the Witwatersrand gold mines in 1928 as a replacement for battery locomotives. The advantages and disadvantages were recognized in those days, and surprisingly, there are no significant additions to this list, but only refinements. In the absence of any Occupational Exposure Limit (OEL) for Diesel Particulate Matter (DPM) in SA, the Mine Safety and Health Administration (USA) rule is currently being used as a benchmark for the ventilation engineering designs. This paper discusses the ongoing SA journey of measurement and limitations of exposure data for ventilation planning and regulatory purposes. The currently accepted DPM limits are based upon the belief that they are economically and technically feasible for the mines to reach and are not necessarily health based. For SA underground platinum mines, a median TC/EC ratio of 1.8 with a range of 1.2 to 5.8 was observed. For SA coal mines, a median TC/EC ratio of 1.44 with a range of 1.25 to 2.13 was observed. While it is common practice in the USA to use the ratio of TC/EC for metal mines to be 1.3, the ratio found in local platinum mines is 2.2 and for coal mines, the ratio was 1.53 which is lower than Australian studies, i.e., 1.96. It has been shown that a need for critical analysis of TC/EC ratios exists, and possible reasons for variance must be understood before stringent adoption of overseas recommended limits for DPM. It is hoped that the findings from this paper would provide input to scientific approaches in developing appropriate conversion factors, limits for DPM and also in ensuring appropriate error factors (currently 1.14 for TC and 1.2 for EC) for compliance determination.

Jan 1, 2009

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By Nathan Painter, Kevin Andrews, Andrew Karpa

Groundwater flow in bedrock units is an important factor to be considered for most mining situations, both underground and open pit excavations. Characterization of the hydrogeologic system into which a mine will advance is an important factor for slope and entry stability, mine dewatering design, and potential environmental considerations including stream loss and water well damage. In addition, hydrogeologic characterization of bedrock is important for locating water wells and for groundwater contamination mitigation. Hydrogeologic characterization for a site begins with a desktop study and often evolves to include drilling, geologic logging, monitoring well installation, groundwater sampling, pump testing, and packer (Lugeon) testing. In addition to these methods of hydrogeologic data collection, downhole geophysical logging of exploration and monitoring well boreholes provides detailed information associated specifically with in-situ conditions of each hole. The basic suite of geophysical logging tools used for hydrogeologic characterization often includes Optical or Acoustic Televiewer (O/ATV), full wave sonic, gamma-density, fluid temperature, resistivity, specific conductance, and flowmeter. For many hydrogeologic settings, groundwater flow in the bedrock is dominated by discontinuities, or fractures, in the rock. O/ATV logging allows for determination of the frequency (clustering), orientation, and aperture width of in-situ fractures, while sonic logging allows for estimation of intact rock strength. Fluid temperature logging and flowmeter measurements provide insight with regard to potential groundwater inflow zones, and other tools provide information for geologic unit contacts. This paper outlines the process and benefits of using downhole geophysical logging for hydrogeologic characterization and provides generalized examples from industry experience.

By Bernd-Arno Behrens, Klaus-Georg Kosch

"In times of increasing energy costs automotive lightweight construction is gaining in importance. This paper deals with the production of hybrid steel-aluminum compounds by forging. The compound forging process is a promising method to successfully manufacture functional parts by applying resource-saving process steps. Nevertheless, challenges resulting from different material properties must be solved.The heating of hybrid material work pieces made of steel and aluminum is a great challenge. Steel is forged at a temperature of at least TSt =900 °C, while aluminum should not exceed a temperature of TA1= 500 °C. For achieving the required temperature gradient extensive experimental investigations have been carried out. Intermetallic phases form during the manufacturing process and can influence the bonding and the global part quality. In addition, methods for the characterization of the joining zone between the materials steel and aluminum are analyzed and the factors influencing the formation of intermetallic phases are determined experimentally.IntroductionIn times of increasing energy costs and stricter conditions relating to environmental protection, automotive lightweight construction is gaining in importance. The production of hybrid compounds by forging is a promising method to manufacture functional parts by applying resource-saving process steps. In compound forging a hybrid raw part consisting of a solid core, which is enclosed by a hollow casing, is joint in the forming process. This results in a graded material structure in the part in which the mechanical properties can be specifically adapted to the requirements. Compound forging is the form joining and/or firmly bonded joining of at least two different materials while plastic shape forming occurs (Figure 1)."

Jan 1, 2012

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By H. M. Roche

MAGNETITE mining and milling in the Eastern States was sharply curtailed in 1938, production showing a decrease of 36 per cent from 1936 and 57 per cent from 1937. Six mines, one in Pennsylvania, two in New York, and three in New Jersey were in operation, either part or full time, during the year. In recent years ten Eastern magnetite mines have been more or less active but since the World War the market for Eastern ores- has been spotty. The scrapping of Eastern merchant pig iron furnaces, imports of cheaply mined duty-free foreign ore, and high freight cost have been contributing factors.

Jan 1, 1939

By Erwin Pink

It has been pointed out in a previous publication' that, for a given strain rate, serrated yielding can be observed only at certain test temperatures. Fig. 1 shows the results obtained for polycrystalline and re-crystallized tantalum, Va group in the periodic table of elements, where serrations in the course of deformation match the decrease of total elongation. However, there was no evidence of repeated yielding when testing molybdenum or tungsten, VIa group, at similar conditions, i.e., annealed and air-cooled samples (serrations have been found in quenched tungsten2). The reason for the observed serrations in the stress-strain curve are dissolved impurities on interstitial sites of the lattice. Of importance is the concentration of oxygen, carbon, and nitrogen, which are in random solution. Two methods to calculate the limiting concentrations for serrated yielding have been evaluated and applied with more or less success in estimating the role of carbon and nitrogen in mild steel.3 J. Friedel4 has given two equations, which determine the upper and lower strain rates i for the appearance of serrations at a certain test temperature: W denotes the binding energy of the interstitial atom, -1 ev for refractory metals;5 e' the portion of continuous strain in the discontinuous stress-strain curve, measured as -3x10-3; b the Burgers vector, c the concentration, see Table 11, in atom fractions; p the dislocation density, -2 X l09 per cm2 at an average stress ?, -15 kp per mm2 at medium strain. k stands for the Boltzmann constant, T for the absolute temperature, and D for the diffusion coefficient. Table I. Eq. [1], for a given strain rate, determines the minimum temperature, and [2] the maximum temperature, below or above which no "dynamic strain-aging" can occur. According to the calculation, which uses the given quantities, serrations should only be observed within the cross-hatched temperature regions in Fig. 1, and this is in good agreement with the experiment. The effect of varying impurity concentrations is indicated schematically in Fig. 2: only Eq. [I] is affected. Setting Eq. [I] equal to [2], one can calculate the limiting concentration cmin which first causes serrations. The second method uses the aging condition by Cottrell and Bilby6,7 \£i/ \ n. a / where n(t) is the number of impurity atoms, which segregate at a dislocation line of 1 cm length after the time t (t in our case is the time between "repeated yield drops" in the serrated curve, or, the time until the above mentioned strain E' is obtained, i.e., -1 sec for medium intensity or serrations). no is the number of impurity atoms in 1 cm3 and A = Qb4ep[(1 + v)/(l - v)], derived from equations given in Ref. 7. p is the shear modulus, 18,800 kp per mm2 for tantalum, 12,200 for molybdenum, AE the tetragonal distortion caused by interstitial impurities in a bcc lattice (approximately 0.4 for both tantalum and molybdenum) and v Poisson's ratio (0.35 for tantalum, 0.30 for molybdenum). From Eq. [3], combined with the condition for a pronounced yield drop as formulated by cottrel16 (at least one impurity atom segregated at the unit length of a dislocation), again a no min, and hence the concentration Cmin can be calculated.

Jan 1, 1970

By J. M. Campbell, T. S. Buxton

The most widely used methods of predicting the volumetric properties of gas are based on the principle of corresponding states, which asserts that the compressibility factor is a universal function of reduced temperature and pressure. Previous studies have shown that the acentric factor, as proposed by Pitzer, l is an important addition to reduced pressure and reduced temperature as factors affecting the compressibility factor. Results of this study indicate that, if the pseudocritical temperature and pressure used to determine the reduced conditions are adequately predicted, characterization of natural gas-carbon dioxide mixtures with the acentric factor will allow reliable determination of the compressibility factor. Comparisons of predicted and experimental compressibility factors have shown that the pseudo-critical constant rules of Stewart, Burkhardt and Voo 2 are satisfactory for hydrocarbon mixtures. However, these rules fail to predict the pseduo-critical constants for hydrocarbon-carbon dioxide mixtures. Based on graphically determined pseudocritical temperatures for binary hydrocarbon-carbon dioxide mixtures, a correlation which gives the required correction to the Stewart, Burkhardt and Voo rules was prepared and a compressibility factor prediction technique was proposed. To test the proposed technique, compressibility factors for live mixtures of methane, carbon dioxide and either ethne or propane were experimentally determined at 100, 130 and 160F and pressures up to 7,026 psia. The predicted and experimental compressibility factors for these live mixtures had an average absolute deviation of 0.55 percent. INTRODUCTION Two-parameter generalized correlations based on the principle of corresponding states (PCS) are presently available for reliably predicting the compressibility factor of lean natural gas, i.e., natural gas with low concentrations of hydrocarbons heavier than methane. When these same correlations are used for mixtures of natural gas and carbon dioxide, large deviations between actual and predicted compressibility factors are observed. This study was undertaken to provide a means for accurately predicting the compressibility factor for such mixtures. In the past, two avenues of approach have been employed to extend the applicability of the PCS. The first has been to introduce additional parameters. The second has been to develop combination rules for predicting pseudocritical constants which do not suffer from the limitations of the commonly used molal average constants. In this study, both of these approaches have been considered and employed to arrive at a method for predicting the compressibility factor of mixtures of hydrocarbons and carbon dioxide. SELECTION OF A THIRD PARAMETER Failure of the original PCS to predict the compressibility factor for all pure gases, regardless of their mass, shape or polar moment, has led to the introduction of additional parameters into the PCS. Parameters have been introduced to correct for quantum deviations,3-5 non-spherical or globular shapes6-9 and for polar moments.8-12 In addition to these parameters which are based on some microscopic property and intended to correct for some specific cause of deviation, more general parameters based on some bulk property have also been introduced.1913-16 To use additional parameters to correct for each of the possible causes of deviation among the individual constituents of a gas mixture would require a rather complex form of the PCS. To maintain the PCS in as simple a form as possible, it is more desirable to have a single third parameter which is based on some bulk property influenced by several of the factors causing deviations. The third parameter selected for use in this study is a factor originally proposed by Pitzer.9

By William R. Chedsey

IN the last two years the E.C.P.D. committees having to do with the inspection of engineering schools for possible accrediting have been concerned with the engineering content of some of the mineral industries courses. Originally the discussion arose with regard to engineering geology, or geological engineering, afterward broadening to metallurgical engineering, ceramic engineering, agricultural engineering, and other branches not pertinent to this discussion. Some members of visiting committees took the attitude that they probably would have to accredit these types of training as included in the engineering group if they met the average standard set by the mining schools, though they questioned -whether they were really engineering.

Jan 1, 1939

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Daniel R. Hack

This paper point out the development of optimized routines for the processing and analysis of field data, continually building a framework for further software development. It also describes the possibilities for future development in the realm of 2D variography for surface water heat flow systems using existing proprietary and academic software packages.

Jul 17, 2000

By A. K. Ghose

The increasing application of roadheading machines in the coal industry has prompted the development of an appropriate selection methodology for such machine applications in specific locales. Accurate geological sections and comprehensive rock testing are required for all machine tunneling. Using suitable geotechnical parameters and index tests, sensitive both to excavability and standability of the strata, a classification scheme has evolved to help evaluate the rock mass vis-a-vis application of a given weight-class of roadheading machine. The classification parameters include point load index, brittleness, abrasiveness, average crack density, and ground water, which with assigned numerical ratings, lead to a quantitative global rating of the rock mass. For each rock mass class, the selection of an appropriate roadheading machine is recommended. The paper illustrates the application of the rock mass rating system and also describes simple index tests for evaluating the classification parameters for brittleness and abrasiveness. Manuscript not received in time for publication.

Jan 1, 1983

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

By T. L. Joseph

A DEMAND for specialized knowledge has directed engineering curricula towards competency in some particular field or occupation. Preparation for life in a broad sense of completeness has received little consideration. Ways and means are needed for weaving some of the threads of liberal education into the fabric of engineering education. Any effort to develop a humanistic-social stem of engineering education will depend largely upon the content of the courses and the type of instruction offered. Many of the courses in college curricula are intended to lay a foundation for more advanced courses to be taken later by those. who specialize in some particular field. Students in other fields lack the background necessary to take the advanced courses and have too much detailed information, soon forgotten, forced upon them if they pursue the foundation courses. To develop a humanistic-social stem for engineering education existing catalogue courses selected should follow some general plan aimed towards broad educational objectives. Courses packed with detailed factual information are necessary for the stu-

Jan 1, 1947