Search Documents

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

Note by the Secretary.-—In the preceding communication of Mr. Rickard, in the present discussion, as printed in Trans., xxiii., the loss of quicksilver at Pestarena, reported on p. 569, as 230 and 234 grammes per metric ton, is stated as equivalent to about 74 pounds per short ton avoirdupois—an obvious error, which escaped correction in my reading of the proofs, and was not discovered until after Vol. XXIII. had left the press. The true equivalent is 0.46 pound or about 7 1/2 ounces (instead of pounds) per short ton.— R. w. R. Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard's last contribution to this discussion* calls for some reply from me, if only by way of defending myself against the charge (p. 569) that my criticisms of his paper were "unnecessarily hypercritical and occasionally unfair." At the same time I am fully aware that our Transactions are not the place for mere personal controversy, and that the sole object of discussion is to define differences of opinion, and defend opposing views as a means of eliciting the truth. Mr. Rickard disclaims the statement, which he says I attributed to him, that in the slow-crushing Gilpin county mills the pyrites remain longer in the mortar than the other portions of the ore. My understanding of his statement was based on the following passages in his paper: " Particles of ore, which have heen pulverized to a fineness which would permit of their exit through the screen, are enabled to settle towards the bottom of the mortar. It would he expected that the heavy metallic minerals occurring in the ore would, because of their greater specific gravity, be most affected by this feature of the treatment. In practice this is found to be so. The fine slimes contain a large proportion of metallic sulphides, generally valuable on account of their close association with the precious metals, while the coarsest particles to be found in the tailings usually consist of quartz and other minerals forming the less heavy gangue (Trans., xxiii., 139).

Jan 1, 1895

By E. Bélisle, Christopher W. Bale, S. Petersen, C. Robelin, K. Hack, J. Melançon, G. Eriksson, A. D. Pelton, P. Chartrand, S. A. Decterov, I. H. Jung, A. Gheribi

The FactSage® package consists of a series of information, database and calculation modules that enable one to access pure substances and solution databases and perform thermochemical equilibrium calculations. FactSage was originally founded by process pyrometallurgists and has since expanded its applications to include hydrometallurgy, electrometallurgy, corrosion, glass technology, combustion, ceramics, geology, environmental studies, etc. With the various modules one can perform a wide variety of thermochemical calculations and generate tables and graphs of complex chemical equilibria and phase diagrams for multicomponent systems. This paper presents examples of recent and current developments in FactSage in areas of particular interest to Dr. David Robertson. These include both ferrous and non-ferrous processing, as well as solidification and refining simulation. The paper also includes reference to the Internet Fact-Web education package.

Jan 1, 2014

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By ARCHIBALD DOUGLAS

BY this time almost everyone knows, in a general way, the corporate income distribution policies of the 1936 Revenue Act, and many of the practical problems arising there under. This article is not intended to be a technical discussion of that act by title, subtitle, section, or supplement, nor an analysis of inter- dependent sections of the various acts over many years woven on the fiscal loom f our Congressional machine. Such a discussion would require the spinning of a web of words too long for patience. Yet ,a general statement of the underlying plan of the 1936 Act, so far as it affects dividend policies, is perhaps useful.

Jan 1, 1937

By Robert H. Peters

Are the safety rules in your work place effective? Do supervisors enforce them as they should? Do supervisors abide by these rules? Safety rules are an important aspect of many company safety programs, particularly if employees must work in an intrinsically hazardous environment such as a coal mine. However, for various reasons, supervisors sometimes fail to enforce safety rules (Arvey & Jones, 1985; Hartshorn, 1998). This paper presents some findings obtained from interviews with coal miners about why supervisors sometimes fail to enforce an important mine safety rule. It also contains a few suggestions addressing what could be done to help supervisors perform this job function more effectively.

By M. Muinonen, R. Pandher

Royal Nickel Corporation is developing the Dumont Nickel Project, a large nickel sulphide deposit located near the town of Amos, Québec. The nickel occurs as pentlandite, heazlewoodite, and awaruite. The relatively low grade ore can be processed to a very high grade nickel concentrate, containing 29% Ni. The absence of copper and precious metals in the ore renders this concentrate amenable to processing by dead roasting in a fluid-bed roaster and smelting in an electric furnace to produce ferronickel for sale to stainless steel producers. Laboratory test work and conceptual engineering design was completed to demonstrate the amenability of Dumont concentrate to produce ferro-nickel.

Jan 1, 2015

By Arthur T. Word

STANDING room only seemed to be the order at the annual session and luncheon of the Eastern magnetite committee. Gatehouse check at the former indicated at least 80, with 33 attending the luncheon - all the crowded facilities could handle. Chairman Crockett opened the meeting by calling upon Meredith E. Johnson, who presented his illustrated paper on "Prospecting for Iron Ore in New Jersey in 1943." This "wartime" brief was discussed by Lucien Eaton, P. W. Henry, and Chairman Crockett. H. E. Hawkes, Jr., of the U. S. Geological Survey, then presented his unscheduled paper on the "Magnetite Deposits of the Jersey Highlands." Discussion was by A. W. Pinger and Chairman Crockett. Fred E. Stiefel then described shaft sinking at the Fisher Hill mine of the Republic Steel Corp., giving a detailed description of how modern

Jan 1, 1944

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By L. B. Gittinger

Mr, Chairman, members- and guests of the AIMS, I greatly appreciate this opportunity to speak before you. I hope this is just the beginning of a long and mutually beneficial relationship. This winter I decided to join the other 36 Freeporters who belong to the AIME; and, I applied for membership in the Society of Mining Engineers. To queries as to my interests in the Society, I had this answer: our principal challenge -- more so today, than at any time in my nearly 25 years in the industry -- is discovery and development of new sources of raw materials. I want to join you in meeting this challenge.

Jan 1, 1966

By P. R. Ineson, D. W. James

For a criterion to be useful it must either demonstrate directly the role of exhalative processes in the formation of a deposit or describe a unique attribute of exhalative deposits. Few of those employed in previous investigations entirely satisfy either condition. The limitations of three of the most frequently employed criteria are illustrated by studies of the geology of the King Island Scheelite deposit in Tasmania.

Jan 12, 1993

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

Remarks of Mr. Robert W. Hunt, General, Superintendent, Albany and Rensselaer Iron and Steel Company., Troy N. Y.—In discussing Dr. Dudley's two most interesting papers, I feel a natural hesitancy in disagreeing with conclusions formed after such careful and conscientious work. But I think he has made his deductions from too meagre premises. The analyses of but twenty-five samples are entirely too few to justify the establishment of so important a formula. When we consider that he indirectly proposes to regulate an interest amounting, even at the present low prices, to over $20,000,000 per annum, we may well hesitate before accepting a formula based upon the chemical and physical analyses of but twenty-five steel rails. Dr. Dudley touches the keynote in referring to the proposed labors of the Government Test Commission. They based their hopes of attaining success upon the chemical and physical analyses of a very large number of samples, and in the only branch of investigation which the short-sighted policy of Congress has allowed them to complete, i.e., chain cables, we find that a dozen, twenty-five or one hundred tests gave no satisfactory results. It was only after many hundreds that they were enabled to' draw conclusions. There are so many circumstances hearing upon the life of a rail, that the task of extracting a correct result seems herculean. I presume I am right in stating that in our Northern latitudes early winter and spring months witness the breaking of the greatest number of rails, thus seeming to prove that an unstable road-bed has much to answer for. Then, again, broken and flattened wheels must be taken into account, but I am convinced that more rails have been broken by the treatment which they received before leaving the rolling-mill

Jan 1, 1879

By E. C. Hoeman, W. C. Stoecker, R. C. Redfield

"INTRODUCTION Industrial sands, characterized by specific physical and chemical proportion, are,essential new materials for the manufacture of glass, sodium siliante and other products. Sands of suitable characteristics are used extensively for molds and cores in the casting of metals as a granular medium in municipal water filters, as abrasives, as traction sand to prevent the slipping of driving wheels of self-propelled vehicles on trucks and in various ceramic and other structural forms. In addition to the use of common silicon sands in concrete, cement, and mortar, special sands find use in sand-lime brick oxychloride cement, and flooring, for coating prepared roofing, and for placing ware in saggers although sand for sandpaper has been mostly displaced by other harder mineral or synthetic grains, other abrasive uses are numerous and include sandblasting stone sawing, glass burnishing and finishing."

Oct 1, 1945

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By Bruce D. Hebb, Shahin Shadlou

Fiber Reinforced Polymer (FRP) is an excellent material choice for a broad spectrum of corrosive fluids and, in many cases, offers the best value per dollar. FRP Flanges present the greatest design challenge of all standard piping components. The theory underlying the design of flanges is very complex. In addition, due to the nature of FRP material, proper fabrication of the flanges is as critical as the design. In this review, the challenges of making FRP flanges along with the design techniques and best practices of fabrication that will lead to a high-quality flange will be discussed.

Feb 1, 2024