Search Documents

By Edward K. Landis

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By David W. Wisecarver, James F. Reynolds

INTRODUCTION The Department of Energy is cooperating with Snowmass Coal Company near Carbondale, Colorado to introduce the longwall mining method in moderate to steeply pitching coal seams in the United States. This venture is part of a coal mining research program directed toward development, trial, and analysis of mining technique8 to improve production and recovery in the more difficult mining conditions such as thick, multiple, and steeply pitchly seams found in the Western U.S. The project at Snowmass is the first attempt in the United States to operate a longwall in a steep coal seam. Plans are to mine three adjacent, successively downslope panels in the eight foot thick seam which varies in pitch from 27 to 33 degrees. During this work, researchers and mine engineers are expected to obtain answers to many engineering questions relative to panel design and development, selection of face equipment and beet operating techniques and procedures. They are also committed to obtaining hard data on costs, recovery, production, safety, and behavior of underground mine structure as the three panels are mined. This information is essential to future mine engineering and profitable mining of pitching Western coal reserves. Development of the first trial panel was begun in 1979 and completed in June 1981. The longwall mining equipment was then installed in the starting room and retreat mining begun on August 11, 1981. Project duration is expected to be about five years during which over tm million tons of coal will be produced. TRAINING The longwall mining method is new to Snowmass. For years the mine produced coal by room and pillar methods using conventional techniques to mine upslope rooms and Alpine F6A miners to cut entries and rooms on strike. Miners were experienced in room and - pillar mining from other mines. News of the longwall demonstration was received enthusiastically by Snowmass miners. Employee interest in the project was 100%. However, there was minimal longwall experience on site. In fact, most of the work force had not even seen a longwall. Mine and company management were well aware of the immediate need to develop trained longwall face mining crews and maintenance people qualified to work on longwall equipment and also expertise in longwall planning, equipment selection, power distribution design, ventilation requirements and panel development. The first approach to answer this huge deficiency in longwall mining experience was obviously training. Hence a training program directed toward those mining specifics most urgent to the beginning mining phases was initiated in mid-1980. Classroom lectures and hands on training, using instructors from equipment suppliers and available company longwall expertise, was conducted in longwall subjects to include face mining procedures, panel development, operation of equipment, equipment assembly and maintenance, electrical circuitry and controls, ventilation, move of longwall equipment, and safety procedures. At the same time, responsible engineers and foremen were sent on a tour of European pitching longwalls to see first hand how other mines working under similar seam conditions conducted their operations. Development techniques, types of equipment, methods for transport of men and materials, and ground control techniques were discussed with engineers, foremen and officials at each mine. This look at European longwall mining operations gave Snowmass good insight into the unique problems associated with longwall mining on 30' pitch. Mining considerations such as face conveyor/ support system slippage downslope, panel development, maintenance, safety considerations, manpower requirements, and haulage methods were covered with European experts

Jan 1, 1982

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By Else D

While the underground mining work environment may have processes and equipment considered unique, most of the broad issues likely to affect the occupational health and safety of employees are not. One such occupational health and safety issue that is common to the mining sector and most other industries is noise. Noise as an occupational health and safety issue is of national significance. Presently noise induced hearing loss costs Australia around $35 million per year on compensation claims experience alone. Noisy equipment and work environments are still being tolerated in parts of the mining industry as `part of the job'. Where work has been undertaken in noise management, considerable emphasis has been placed on either industrial hygiene monitoring programs or the provision of hearing protectors to miners working on or around noisy equipment.Opportunities for more cost-effective and long term methods for controlling noise exist. Ready to apply solutions to noise problems in the mining industry are available, but for many mining operators this information is often difficult to obtain. To overcome this problem, the SHARE program collects and distributes solutions to occupational health and safety problems. The program aims to help organisations to close the gap between what is known about solving health and safety problems and what is actually being applied at the shop floor level: Recent developments have incorporated the SHARE program concept into worksite hazard management projects that involve the participation of employee representatives, front line supervisors and engineering personnel. Besides providing workforce members with an increased understanding of hazard management skills, the SHARE in-house program results in the implementation and sharing of solutions to health and safety problems by the program participants.

Jan 1, 1992

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By Steven D. Scherer

The highest earthquake risk in the United States east of the Rockies is along the New Madrid Fault System, which extends for 193 km (120 miles) through the Central Mississippi Valley from northeastern Arkansas, through southwestern Missouri, western Tennessee and western Kentucky to southern Illinois. Historically, this fault has generated some of the most powerful earthquakes in U.S. history, notably three Magnitude 8 events in 1811. Apart from the West Coast, this region experiences more earthquakes than anywhere else in the United States, with more than 200 events recorded along the fault annually. These events are typically of much lower magnitude than those experienced in California. Most are too small to be felt. However, should a significant event occur, damage can be expected to be widespread because of the underlying geology. In recent years, earthquake preparedness and seismic upgrade of vulnerable structures has become a focus for a number of State Departments of Transportation, including those in Illinois and Missouri where there is a potential for future damage. This paper presents three case histories illustrating three different techniques used to retrofit interstate highway bridge foundations bearing on potentially liquefiable soils. Friction minipiles were installed at the approach span of the I-57 bridge crossing the Mississippi River near Cairo, Illinois to provide additional support to the pile caps in the event of liquefaction of the underlying sands during a seismic event. In St Louis, Missouri, rock-socketed minipiles were installed to increase the capacity of drilled shaft foundations supporting a section of Interstate 64. In Mounds, Illinois, compaction grouting was used to densify loose sand deposits beneath a pile-supported interstate bridge on I-57.

Jan 1, 2001

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By F. N. Kissell, R. J. Bielicki, J. H. Perkins

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By Donald P. Moore

During April 1967 a Frasch sulfur mine was placed in operation near Fort Stockton, Pecos County, in West Texas. This was the first Frasch mine to recover native sulfur from a deposit not associated with the caprock of a salt dome. Since 1967 two additional mines have been opened in west Texas, another one near the first at Fort Stockton and a third one near Orla in Culberson County (Figure 2). Recoverable reserves at the Culberson County mine are estimated to be 57,000,000 long tons of native sulfur (Zimmerman and Thomas, 1969). Total recoverable reserves at the three mines probably exceed 60,000,000 long tons, Studies of the geochemical cycle of native sulfur mineralization in test Texas indicate an origin similar to the deposits on salt domes although the geologic framework is different. A comparison of the geologic setting of the west Texas deposits with the deposits in the Union of Soviet Socialist Republics as reported in the literature, reveals many similarities. ACKNOWLEDGEMENTS The writer wishes to express his appreciation to Cities Service Minerals Corporation for support throughout this study. Special thanks are due Dr. Chris Riecken and Mr. Dave Hardy for their

Jan 1, 1971

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By Will H. Coghill, I. L. Feld, G. D. Coe

"INTRODUCTION During the course of research on the beneficiation of the Big Seam iron ores of Birmingham, Ala., an urgent need was felt for quick iron assays of grab samples for mill control. Since the gangue minerals in these ores - quartz, limestone, and clay - all have about the same specific gravity, the use of a specific-gravity method was anticipated as a means of measuring the iron content. The idea of estimating the composition of a mineral mixture by measuring its specific gravity is by no means new. However, the usual method of carry in out this idea proved unreliable when applied to the Big Seam ores. The usual rapid method of determining specific gravity consists of measuring the volume of a known weight of sample that has been dried at high temperature. The inadequacy of this method led to the development of the rapid, modified, specific-gravity determination described in this paper.This work- was an incidental development resulting from research on beneficiation of iron ores by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and ore producing companies of the Birmingham district."

Jan 1, 1946

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015