Search Documents

By F. B. WEEKS

I HAVE chosen for my subject a mining district which in an article published four years ago I referred to in the following words: "One of the un- usual anomalies of mining development and history is that a district having added thirty or more millions of wealth to a principal mining state, situated within four to six miles of two transcontinental railways and two auto highways, and within 150 miles of the most widely advertised part of the United States, should have been so completely lost sight of that probably not one mining man in ten can tell offhand where it is situated." But this district never was a dead one: it was only slumbering. During the past four months, day by day, it has been emerging from that state of slumber.

Jan 1, 1929

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By G. Aertsen

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J).-This excellent paper fills a gap in our Transactions and is most acceptable. In the early days another way of casting tire ingots, sometimes called cheeses, because of their shape, was to use a 22-gage sheet-iron cylindrical can for each ingot of the proper size to give the weight desired. These cans were bottom cast in groups, usually of four, each can being surrounded by a heavy iron ring somewhat taller than itself the top of the can being covered by a circular cast-iron plate having a small conical riser in the center, about 2 ½ in. in diameter at the bottom and 10 in. high. The top plate was clamped down to resist the upward pressure of the fluid metal and the space between the can and the outer ring, usually about 2 in. wide, was filled with dry sand. The riser permitted the escape of some of the air displaced by the steel and also increased the pressure in the steel when the mold was filled, and so diminished somewhat the tendency for gas holes to form. But little was known of segregation and pipe in those days, though the center of an ingot was understood to be the worst part, and it was separated in part in the disk which was punched out in perforating the ingot. This disk was about 8 in. in diameter and from ¾ to 2 in. thick, the variation in thickness being to rectify the weight. When an ingot was too -heavy, a thicker disk-was made by not driving the punch in quite as far as when the ingot-weight was right. Then the bloom was turned over and the punch driven in on the other side, which finished the punching and detached the disk. The tire bloom was then" becked" and later reheated and rolled as described in the paper. The forging was done with a 10-ton double-acting steam hammer. The steel generally speaking had lower carbon, from 0.45 to 0.55 per cent., than tires today have, and the tires were smaller, the most common size of ingot weighing 1,060 lb. each. BRADLEY STOUGHTON, New York, N. Y.-This paper was specially requested by the Iron and Steel Committee, because that Committee thought so important an industry should have its history written by one who was familiar with it, and before he had forgotten, or all the rest of the world had forgotten, its early stages. Mr. Aertsen has said that it is not an exhaustive research. I think it would not be any different if it were an exhaustive research, because our library made a careful attempt to find some written light on the history of these tires, but very little was found.

Jan 4, 1917

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By A. C. Richardson

During the past two and a half years the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive study of coal preparation in the State of Alabama. Considerable time has been devoted to the study of the washing characteristics of the Mary Lee bed and the various methods used in preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery Of the Republic Steel Corporation, Sayreton, Ala.

Jan 1, 1931

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

Grains are subject to contamination by mycotoxins which are metabolic by-products of various fungi. The fungal infestations produce local concentrations of the mycotoxins thousands of times higher than the average. These facts make the sampling of the grain for assessment of the mean mycotoxin levels potentially very difficult. In the context of sampling theory, this morphology of the infestations creates a very high distributional and intrinsic heterogeneity of the grain shipment. The distributions of mycotoxin concentrations in seaborne shipments that exist at loading and the number and intensity of infestations that develop under shipping conditions are unknown. All grain shipments carry spores that may give rise to mycotoxin-producing colonies; moisture and temperature determine the final extent of the problem. This paper develops the value of the sampling constant with respect to intrinsic heterogeneity based on data on observed Ochratoxin A (OTA) concentrations in individual wheat kernels. A useful relationship between the distribution of mycotoxin concentrations on a kernel to kernel basis and the distribution of concentration over subsamples is developed.

Jan 1, 2009

By M. Ashraf Mahtab

A feature of interest in stability of excavations in domal salt is the phenomenon of gas outbursts which has occurred in five of the six mines in Louisiana salt domes. Gas outbursts are sudden erruptions of salt and gas from the face or roof of a mine opening. They are associated with anomalous zones in salt, depth of mining, and the method of excavation. Potential risks from gas outbursts include an unplanned connection to a reservoir of water or hydrocarbons and, possibly, a loss of the mine. It is proposed that a gas outburst is initiated by disking in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement of the cavity to the boundaries of the pressure pocket. Identification of burst- prone areas will require research into in situ measurement of material characteristics and further under- standing of the mechanism of gas outbursts. Shock blasting in advance of mining appears to be a promising technique for controlling gas outbursts.

Jan 1, 1981

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994