Search Documents

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By S. M. Spottiswoode

The aim of the hybrid location method is to improve seismic event locations by reducing the effects of errors in the wave velocity of ray paths between each event and each recording site. We report on further enhancements made to the hybrid location algorithm, which is based on the double-difference method developed by Spottiswoode and Milev1and Waldhauser and Ellsworth2. The term ?double-difference? refers to the residuals between the observed and theoretical travel-time differences and are obtained using either picked arrival times or various measures of time differences obtained from waveform pairs. These residuals are minimized for pairs of earthquakes at each station while linking together all observed event-station pairs. An important enhancement is that the double-difference term uses the median arrival time residuals to reduce the effect of outliers on the system of equations. In addition, the hybrid locations are further constrained by considering events of known locations, in this case along lines of development blasts. We relocated some 20 000 previously located seismic events in the Driefontein 5E area; 5 800 of these events were considered to have been development blasts and we constrained their locations to lie on the straight lines joining about 2 150 survey pegs from the mine?s database. Relocated events were shown to distribute more closely around advancing faces than had been the case before relocation. Wave velocities from the development blasts show evidence of anisotropy.

Jan 1, 2005

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By J. E. Moyle

Introduction In October 1983, Rio Algom Ltd. decided to develop the East Kemptville tin deposit. This decision was the result of intensive geological and metallurgical evaluation work, as well as careful studies of environmental and marketing aspects. The property is located about 54 km (34 miles) northeast of Yarmouth, Nova Scotia, near the village of East Kemptville. Geology The geological setting is a granitic intrusive at the contact with metasediment. The tin mineralization is in the form of cassiterite (SnO2), which is about 80% tin. Sulfides are associated with the deposit containing silver, copper, and zinc, which are recoverable as byproducts. The mineralization is associated with quartz veins and greisen alteration. In the center of the deposit, the zones are so close together they have the appearance of a massive or porphyry type deposit. Ore Reserves The mine plan is based on 56 Mt (62 million st) at 0.165% tin. Up to the ninth year, mill feed will average about 0.2% and lower grade material will be stockpiled. In later years, the average grade will be 0.16% tin. A 0.08% cutoff grade is planned for the entire 17 years of production. East Kemptville is a relatively low grade tin deposit, and only a combination of favorable circumstances has made it economic. • The ore body is situated at, or very close to the surface, permitting mining by open-pit methods at a very low stripping ratio. • The tin occurs in relatively large crystals that allow for good recovery by gravity techniques. • It is ideally located in a well-settled area, with all essential infrastructural requirements already in place. • The positive and cooperative response from various governmental agencies involved are encouraging. Mine Plan The mine plan incorporates an initial pit, followed by three expansions to the ultimate pit. Mining will be at 14 kt/d (15,000 stpd) and will include 9 kt (10,000 st) of ore plus 5 kt (5,500 st) of waste and low grade. After five years, the mining rate will increase to 21 kt/d (27,500 stpd). It is planned to drill vertical 165-mm (6.5-in.) blast holes on a 6-x 6-m (20- x 20-ft) pattern. Bulk slurry explosives will be used to break the rock. Loading will be with hydraulic shovels into 70 t (77 st) haulage trucks. The trucks will deliver the ore to a 13 x 20 m (42 x 65 ft) gyratory crusher, where it will be crushed to 150 mm (6 in.). Secondary and tertiary cone crushers will be used to further crush the ore to 13 mm (0.5 in.). Process Design Tin extraction technology is practically unknown in North America, but Rio Tinto Zinc, which has a 53% ownership in Rio Algom, is involved in tin production in the UK. Rio Algom has used this experience and expertise in metallurgical evaluation work and in tin-related aspects of plant design. Mineralogical and metallurgical test work have been performed, both on laboratory and pilot plant scales. Mineralogical work was done largely in the UK, the laboratory test program was carried out at the Lakefield research facility in Ontario, and pilot plant work was conducted in Australia. This program has resulted in significant improvements in recovery and concentrate grades, over best projections that could be made before this work was carried out. Concentrating Process The concentrator is being designed to process about 9 kt/d (10,000 stpd). The first step is to reduce the size of the ore to -700 µm (-24 mesh) in a rod mill/ball mill grinding circuit. The ball mill will operate in closed circuit with high capacity banana-type screens. The screened product will be deslimed to 30 µm (560 mesh) with cyclones, then passed over the pri-

Jan 4, 1984

By Robert A. Jankowski, Charles D. Taylor

The objective of this program was to conduct dust surveys at six longwall sections having double-drum shearers, that were regularly in compliance, and to identify the dust control techniques that were the most effective. As each of the mines selected had a record of regular compliance with the Federal Dust Standard, all sampling was "short-term" (often less than 30 minutes) and no attempt was made to relate the survey results to dust-sampling results obtained by the companies for compliance purposes. The sampling procedures (1) used during this survey were developed jointly by the Bureau of Mines and Foster-Miller Associates, Inc. In addition to monitoring dust levels, measurements were also taken throughout the shift to monitor airflow along the face and water usage on the shearer. This program was a cooperative effort of the Bureau of Mines and the Mine Safety and Health Administration (MSHA). The following MSHA health specialists contributed to its successful completion: Paul Lenyo, CMS&H, Dist. 2; Ellis Mitchell, CMS&H, Dist. 3; Carl Jenkins, CMS&H, Dist. 4; David Stritzel, CMS&H, Dist. 8; and John Prelc, CMS&H, Dist. 9. RESULTS CUTTING SEQUENCE - WORK LOCATION At all mines surveyed, an important factor in controlling dust exposure at the shearer is the design of the cutting sequence so as to allow the shearer operator to work most of the time on the intake-air side of the lead drum. It is generally accepted that most of the dust generated by a double-drum shearer comes from the lead drum, which in the raised position normally takes a full sump. Because the position of the drum that is in the raised position determines the horizon control, the operator must be close enough to carefully monitor its operation. Therefore, his position relative to the lead drum has a significant effect on his dust exposure. Dust profiles, such as those constructed from data collected at Mines A and B (Figure 1), show the large gradient in dust concentrations that can exist between the intake and return air side of the lead drum. When the primary cut is taken head to tail, the lead drum is downwind and dust levels can be maintained at a low level until air has passed the shearer (Mine A). Thus, shearer operators can stay in relatively uncontaminated air. When the primary cut is taken tail to head, the lead drum is upwind of the shearer controls, resulting in higher dust concentrations at the shearer operator's work location (Mine B). At the mines where this cutting sequence was used, it was company policy for the shearer operators to walk on the intake side of the lead drum, returning to the controls only to adjust the height of the lead drum. DIRECTED WATER SPRAYS AND PASSIVE BARRIERS It is not always possible to keep the shearer operator on the intake air side of the lead drum. Various techniques have been tried to keep the dust generated by the shearer away from the machine operators when they work adjacent to the shearer. At all mines visited, the external water spray nozzles were directed so that dust from the shearer was directed downwind and toward the face, and away from the shearer operators. The effectiveness of using external water sprays to keep dusty air close to the face was noted during Bureau of Mines efforts to develop improved water spray systems (2). Laboratory and underground tests showed that water sprays located properly and directed downwind can create aiflow patterns that move dust generated by the shearer toward the face and away from the shearer operators. Sprays directed upwind, into the airflow, can actually move dust away from the face

Jan 1, 1982

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined the 9,550-acre Yatahoney Creek Wilderness Study Area (WSA) for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. Owyhee County mining records and U.S. Bureau of Land Management records, and other references were examined prior to the field study. There are no known mines, claims, or prospects in or near the WSA. No evidence of mineral deposits or occurrences was observed. Oil and gas leases or lease applications are in the southern portion and northeast corner of the WSA. Although placer gold exists in the Owyhee River drainage, there are insufficient deposits of gold-bearing gravel in the Yatahoney Creek WSA to enable mining. INTRODUCTION The U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) conduct mineral surveys of designated wilderness study areas (WSAs) 1/ to ensure mineral values that may be present are considered in wilderness recommendations. The USBM examines known mines, prospects, and mineralized sites, and the USGS performs geologic mapping, and geochemical and geophysical surveys on an areal basis.

Jan 1, 1986

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By H. A. Schwartz, Wolfram Ruff

The spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. $ There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others'-', have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8, 9, 10 for cast iron. The problem of deriving from the circular planar intercepts of a mass of spheres of varying sizes their number and size distribution in space has also been satisfactorily solved12, 13 Growth of Nuclei in White Cast Iron It has already been shown1, 3 that the progress of graphitization with time is usual1y consistent with the assumption that nodules grow in size

Jan 1, 1936

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By Wolfram Ruff, H. A. Schwartz

The spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. $ There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others'-', have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8, 9, 10 for cast iron. The problem of deriving from the circular planar intercepts of a mass of spheres of varying sizes their number and size distribution in space has also been satisfactorily solved12, 13 Growth of Nuclei in White Cast Iron It has already been shown1, 3 that the progress of graphitization with time is usual1y consistent with the assumption that nodules grow in size

Jan 1, 1936

By C. R. Hayward

CARLE R. HAYWARD.-I do not want it understood that I think that the conclusion that the time of tempering temperature is immaterial has been definitely proven, but since these are the first definite figures put out, I thought before continuing on more work ourselves, it would be well to present them as progress and for information. J. A. MATHEWS, Syracuse, N. Y.-I think that if Prof. Hayward would consult the paper of Profs. Barus and Strouhal,1 1885, he would find about 250 pages, mostly figures, on this subject, in which they investigated the tempering effect by electrical and magnetic methods. There are so many figures in the paper that it is very difficult reading. One point particularly brought out was that even at a low temperature, such as the boiling point of alcohol, about 60° C., there is a tempering effect, increasing up to 4 hr. One reason they obtained those results, with which the present authors are at variance, was that they started with a high-carbon steel which hardens thoroughly, whereas the steel Prof. Hayward and his collaborator used was a comparatively mild steel which does not take a great deal of hardening. About 3 years ago Mr. Stagg and I published 2 a few figures bearing on the same subject, but we used .a low-carbon alloy steel of high tempering qualities and found a great deal of improvement, particularly in ductility, by continuing the drawing up to 4 hr. We used a chrome-vanadium steel showing after heat treatment 250,000 tensile strength. On short drawing, we got almost no ductility, but by continuing to 4 hr., we raised it to 12 per cent. I believe Prof. Hayward's results are due to using comparatively mild steel, whereas Prof. Barus used drill rod and carried out a, wonderfully exhaustive

Jan 4, 1917

By J. A. Taylor, H. F. Yancey

"INTRODUCTION Froth flotation as applied to coal is a process for separating desirable carbonaceous material from undesirable inorganic matter. In general, the feed must be finer than one eighth inch in size. The principal use of the process in the preparation of coal appears to be in the treatment of the fine sizes produced by breakage during mining and preparation.The Bureau of Vines in Information Circular 6714 has published general information on coal flotation, summarized investigative studies of the process, and described operating plants throughout the world with their tonnage, reagent consumption and operating costs.4ACKNOWLEDGMENTSThe present study of means for depressing pyrite and reducing ash ty froth flotation was conducted at the Northwest Experiment Station of the United States Bureau of Wines in cooperation with the College of vines. University of Washington, under the general direction of A. C. Fieldner, chief engineer, Experiment Stations Division, Bureau of Wines. Grateful acknowledgment is made for suggestions and criticisms received from W. H. Coghill, supervising engineer, U.S. Bureau of Mines Mississippi Valley Experiment Station, Rolla, Mo.; J. B. Morrow, and R. E. Zimmerman, of the Pittsburgh Coal Co.; and Dean Milnor Roberts and Prof. Joseph Daniels, of the College of Mines, University of Washington.FLOTATION AND DEPRESSIONA substance will tend to float if its surface attracts a gas film more strongly than it does a liquid film when both air and liquid are competing for this attraction. On the other hand, a substance will not float if its surface attracts a liquid film more strongly than it does a gas film. All theories of depression depend upon this fact. A wetted particle of floatable size most likely will be found in the tailings after the flotation process has been completed.The crux of flotation is the selective wetting of the undesirable material that tends to float. Two general methods 5, 6, 7 of depression are in use: One combines a chemical substance with the surface to form a wettable compound, and the other employs some colloidal or ionic substance which the surface selectively adsorbs, thereby forming a wettable surface."

Jan 1, 1935

By Charles Zahn

Direct mass spectrometric determination of alcohols in the presence of hydrocarbons has not been possible because of the similarity of hydrocarbon and alcohol mass spectra. Experiments have demonstrated that by converting the alcohols to their trimethylsilyl derivatives, characteristic mass spectra are obtained free of interference from hydrocarbon ion fragmentation. Hexa- methyldisilazane is the reagent selected for the conversion, An improved method of preparing the reagent is given, Mass spectrometric determination of alcohols as trimethylsilyl ethers now is not only possible without prior separation from other materials, but the range of the room-temperature mass spectrometer is also extended to include the C10 alcohol region. Water does not interfere because it is converted to hexamethyldisiloxane, which has its own distinctive mass spectral peak, Experience indicates that other compounds such as glycols, amines, and phenols probably could also be determined by mass spectrometry of their trimethylsilyl ethers. Studies on the similar detemination of phenols in coal oils have been started, When mass spectrometry is not available, gas-liquid chromatography of alcohols before and after their conversion to the trimethylsilyl derivatives probably could be performed. The preparation and properties of the trimethylsilyl derivatives of 23 alcohols, 2 glycols, 3 amines, and 1 mercaptan are detailed. INRODUCTION During investigations by the Bureau of Mines at the Pittsburgh Coal Research Center relative to the development of Fischer-Tropsch processes, complications were encountered in the mass spectrometric analysis of alcohols in hydrocarbon oils. The fragmentation peaks of the alcohols and the hydrocarbons were so similar that an accurate analysis was not possible, Since involved separation techniques are necessary to isolate alcohols from hydro-carbons for separate determinations, efforts were turned to the search for a

Jan 1, 1962

By N. M. Can

The effects of microwave treatment on the floatabilities and magnetic susceptibilities of some sulfide minerals, namely, pyrite, chalcopyrite, galena and sphalerite, were studied. Pure mineral samples were prepared in -425+212-µm, -212+106-µm and -106+38-µm size fractions. Microflotation and magnetic separation tests were carried out on the samples after microwave treatment at 600, 950 and 1,300 Watts for 5, 20, 60, 90, 120 and 240 seconds. The maximum temperature values of the samples were measured during the microwave treatment, and possible altera-tions on the mineral surfaces were determined by X-ray diffraction (XRD) analysis. The effects of microwave treatment are discussed based on the result of microflotation and magnetic separation tests. The results revealed that pyrite, chalcopyrite and galena were heated very quickly and that their surface temperatures reached ~700° to 900°C, while the temperature of sphalerite reached only ~130°C. The floatability of pyrite, chalcopyrite and galena were decreased when microwave energy and the duration of treatment were increased, owing to oxidation of the mineral surfaces caused by relatively high temperature. As expected, there was no change in the floatability of sphalerite. The magnetic properties of pyrite and chalcopyrite were improved by the increase in microwave energy and the duration of treatment to such an extent that 90% of the feed separated as magnetic product. But no change was observed in the magnetic properties of galena and sphalerite.

Jan 1, 2007

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019

By B Mohanty, M P. Roy, P K. Singh

"The measured response of residential structures is a critical indicator of troublesomeor potentially damaging ground vibrations. A study was conducted to evaluate theresponse of structures situated in the periphery of four open-pit coal mines in India. Although, most of the structures were at far-off distances from the present blasting sites, an attempt was made to document the response of structures to blast vibration for future applications to optimize the blast designs for the safety of the structures. The study involved a total 215 blasts, employing one-, two- and three-hole calibration study, and production blasts. The bench height varied from 7.5 m to 42 m, and boreholes loaded with emulsion and slurry explosives were 250, 260, 270 and 310 mm in diameter. The explosive detonated in a blast were between 300-198400 kg whereas in a delay it was 33-24800 kg. Up to 12 tri-axial vibration sensors were located in overburden along a linear array from 25 m to 6.5 km distance from the blasts. Altogether, 1512 blast vibration signatures were recorded. Production and specially fi red single-charge blasts allowed the determination of natural ground frequency. The fundamental frequency of the structures ranged between 3.13 to 10.6 Hz, the same as those of the ground vibrations. The amplifi cation of vibration in the structures was in the range of 1.6 to 5.6. The study details the interaction between ground vibrations and selected structures, and the means to reduce amplifi cation of vibrations in the structures and persistence of vibrations through improved blast design."

Jan 1, 2008

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45' to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By H. Boyd

Fluid energy grinding, or jet pulverization, refers to the process of entraining solid particles in high velocity gaseous or vaporous streams and reducing their size by impact and attrition against other particles or some sort of target. Since all desired size reduction is not achieved in one pass through the zone where energy is applied, some form of classification is necessary to return oversize particles to the grinding zone for further size reduction. Applications Fluid energy mills have normally been used to produce products where the particle size is basically finer than 325 mesh. Products having particle size distributions with a maximum size of 4 or 5 µm, and with a high percentage finer than I µm, can be produced using fluid energy mills. More recently, some fluid energy grinding units have been applied economically to produce ground products with 1 or 2% coarser than 200 mesh. It is also possible to consider usage of a jet-pulverizing zone, without the usual integrated air classi¬fier, operated either in open circuit or in conjunction with a screen. Feed sizes to be delivered to the fluid energy mill depend on the material involved, the type of jet pulverizer used, the finished product size requirement, and the upstream process. In some units feed sizes up to l in. or larger can be accepted, but practical economics usually require the starting material to be -4 mesh or smaller and some pulverizers are typically fed at 20 mesh top size. It is not unusual to find feed materials at essentially -325 mesh when extremely fine products are needed, since capacities are improved with finer feeds. Conventionally the fluid energy grinding process has been used for relatively soft and nonabrasive materials. This includes very low¬melting-point and temperature-sensitive materials or coatings, since there is no measurable temperature rise during fluid energy milling. More recently, however, jet pulverizers are being used on highly abra¬sive materials such as silica, feldspar, glass, zircon, calcined alumina, coke, boron carbide, and similar materials. Since the primary energy application is by impact of particles against themselves, there is a low rate of wear resulting in a small amount of product contamination and in low maintenance costs. Usually the fluid energy pulverizer produces a more narrow particle size distribution than other mills provide, and this is useful where such a requirement exists. It is possible, within limits, to adjust classifi¬cation and other functions of the overall fluid energy system to vary the particle size distribution curve and thereby approach the broader distribution obtained from other grinding methods. By controlling the temperature, composition, and humidity of the fluid used, it is possible to incorporate other functions with the size-reduction process. These include drying or adding moisture, coating, mixing and blend¬ing, and even oxidation or reduction and other chemical reactions or their inhibition. The finished product is discharged in the fluid stream and is conveyed pneumatically to the desired point, where a suitable dust collector must be provided. Operation and Mechanical Features One of the earliest fluid energy mills is the Micronizer now manu¬factured by the Sturtevant Mill Co. Similar units are also manufac¬tured by Jet Pulverizer Co. and others. As shown in Fig. 81, the micronizer consists of a shallow circular grinding chamber with noz¬zles arranged at the outer periphery to discharge tangentially inward. Fluid (usually compressed air or superheated steam) is provided to the nozzles from a manifold at pressures normally in the range of 100-150 psig and at temperatures up to 800°F or higher, depending on the raw material, required results, and economic factors. The com¬pressible fluid expands to high velocity through the nozzles and gener¬ates a spiral flow pattern in the grinding chamber, and discharges

Jan 1, 1985