Search Documents

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By D. M. Fermino, C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. Volzone

The present paper presents the study of light green smectite clay, from Paraiba, Brazil, submitted to mild acid attack under moderated conditions. Usually, clays are subjected to treatment with strong inorganic acids at temperatures near the boiling point and at high acid concentrations and then, widely used as bleaching agents. The treatment occurred under bellow boiling temperature and at short times of reaction (90°C, reaction times of 1, 6, 12, 18 and 24 hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, clay/acid solution ratio of 1g/10mL). The purpose of these attacks is to reduce the concentration of impurities providing color, with minimal change in the clay minerals structure, aiming at use in products of high value such as cosmetics and polymer/clay nanocomposites. The raw clay and the attacked samples were characterized by X-ray diffraction (XRD), cation exchange capacity (CEC), stereomicroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDS).

Jan 1, 2015

By D G. Jefferies

This paper covers National Grid's role in the electricity market, the growth of competition in both generation and supply in that market, and the resulting impact on fuel usage, prices and the environment. It also considers other, external influencing factors on the electricity supply industry, as well as the growing trend towards globalization.

Jan 12, 1997

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014

By G. H. Faye

The prospect of obtaining high-grade concentrates from Canadian pyrochlore ores is rather unlikely, and experimental beneficiation pro-cesses ?appear to have yielded products in the range of 3 to 20 per cent N&apos;b205? A possible solution of the problem is to find an economical chemical method for recovering high-purity Nb2?05 from such concentrates. A technically feasible but economically unproved process is outlined in this paper, in which the concentrate is decomposed by an acid attack and the oxides of niobium and tantalum are isolated and then separated by liquid-liquid extraction. The solution of the ore is adjusted to 7 M HF-5 M HNO3 and the niobium and tantalum are extracted from this solution with methyl isobutyl ketone. The mixed oxides of niobium and tantalum are recovered from the oxdanic phase and dissolved in 0.5 M HF-1.0 M HNO3. Tantalum is extracted preferentially from this solution with methyl isobutyl ketone, leaving niobium in the aqueous phase. By the use of this process it is possible to produce niobium pentoxide and tantalum pentoxi.de in 99.5 per cent purity with a recovery of approximately 95 &apos;per cent, under lab-oratory conditions.

Jan 1, 1957

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By W. C. Brice

Minnesota contains a major copper-nickel resource. In anticipation of requests by industry to develop this resource, the Minnesota Department Of Natural Resources has developed a computerized resource inventory and analysis system, MINESITE This extensive database is available to regulatory agencies as they evaluate mining proposals as required by law. The Resource Analysis phase of the project allows state mining policy decisions to be evaluated in terms of long-range effects on Minnesota&apos;s mining industry and environmental and land use impacts. The analysis also allows for comparison of proposed mine facility sites to a representative range of sites in terms of engineering, site characteristics, and land use and environmental impacts.

Jan 1, 1980

By T. Lee

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domain&apos;s concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By R. H. Lesernann

Copper has held up extremely well as we have moved through the trough of the economic cycle. In the aluminum, lead and zinc industries at least half of the Western World production was unable to cover its operating costs at the prices prevailing throughout most of 1991. In copper, less than 10 percent of production ran in the red last year. Most of that was in Peru where the government has not allowed its currency to devalue at the same pace as inflation. Thus, mining company revenues in local currency terms have risen very modestly while costs have escalated tremendously. Excluding such governmentally imposed distortions, virtually every mine in the Western World ran at a profit last year. While copper producers have to be extremely happy about staying in the black through the trough of the consumption cycle, consumers have to be worried. They must be asking themselves, "If copper held at over $1.00 in a year when consumption declined, how high will prices go when demand picks up?" Consumers are accustomed to paying high prices at the peak of the cycle, but they are also accustomed to paying low prices at the trough of the cycle. What went wrong this time?

Jan 1, 1992

By B Harvey

Achieving community and stakeholder endorsement during life-of-mine planning and implementation requires a business-connected approach, as opposed to charitable giving, disconnected offsets and environmental adventurism.CITATION:Harvey, B, 2014. Extractive companies, development and environmental agendas, in Proceedings Life-of-Mine 2014 , pp 19–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the major disasters in coal mines, and it can have devastating effects on the normal mining and production activities of mines. This paper presents the field investigation, field measurement, data analysis, and formulation of fire-extinguishing measures conducted to extinguish the fire from a coal spontaneous combustion incident that occurred in a high-gas coal mine in China.

By J. L. Holman

The Bureau of Mines is investigating recovery of Ni, Co, Cr, and other metals from mixed contaminated supera110y scrap. The scrap is melt-refined and cast into anodes for electrodeposition of recyclable Ni-Co alloy. Melt oxidation using roasted superalloy grinding sludge as oxygen source can divert the Cr to the slag but with excessive Ni-Co loss. Melt oxidation-carburization or direct melt carburization retains -95 pct of the Ni-Co in the anode alloy. With direct carburization, -90 pct or more of the Cr and other refractory metals report to the anode alloy, largely as carbide phases insoluble in electrolysis. Electrorefining data relate parameters such as controlled cathode potential, Fe and Cr impurities, pH, and compartmented cell use, to current efficiency and Ni-Co deposit quality. Recovery of -90 pct of the Ni-Co in the scrap can be achieved. Preliminary experiments to recover Cr, W, and other metals from the anode sludge and other byproducts are discussed. 347

Jan 1, 1987

By Shu Yamaguchi

The behavior of halide impurities in pyrometallurgical processes such as Wealtz kiln and MF process has been discussed based on the thermochemical data and the reported data of PbO activity in PbCl2-PbO melts. The role of PbCl(g) has been estimated to be significant in the chloridization evaporation reaction. From reported data on the PbO activity in PbC12-PbO melts, activity of PbCl2 has been calculated by the numerical integration of Gibbs-Duhem equation, and the stability domains and the composition of the liquid phase as well as the vapor pressure of PbCl2 have been estimated as functions of log P2HCI/PH2O and temperature. From the discussion of the path during cooling process on the log P2 HCI . PH2O vs. temperature diagram, the authors proposed a possible dechioridization process that utilize water vapor as a dechloridizer for the direct precipitation of PbO from gas phase.

Jan 1, 2003