Search Documents

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By M. Tanaka, Y. Sato, H. Narita, S. Alam, T. Ogata

To ensure a stable supply of rare earth elements (REEs), it is highly necessary to establish the corresponding recycling technologies for RE magnets and phosphors in inplant wastes and endoflife products. Solvent extraction using 2ethylhexylphosphonic acid mono2ethylhexyl ester (EHPNA) is often applied in the separation and purification of REEs. In this study, the equilibrium distribution ratios of neodymium and dysprosium between 1 mol/L nitrate solution and the EHPNA in an alkane diluent were measured at 298K. The experimental data were analyzed by correcting the nonideal behavior of the organic phase using the Alstad empirical equation under the assumption that a complex with a molar ratio of 1:6 (REE:extractant monomer) was formed. The model correlated well with the experimental data and the extraction equilibrium constants were obtained. The extractant equilibrium constants obtained by this methodology would be useful in the design of REE recycling processes using solvent extraction.

Jan 1, 2014

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By Zhiqian Zhang, Chao Wu, Chao Li, Hongxu Li, Chuanqi Jiao

"Many used electronic and optical products contain cerium of rare earth oxides, but it is difficult to recover such rare earth compounds by traditional metallurgy methods. The proposed supercritical water metallurgy is a novel way, perhaps it will be very helpful for rare element recycling, but the thermodynamic properties at such special systems is not clear. In the paper the H20-CeO-CeO2 and H2O-CeO2-Ce2O3 ternary system phase diagram were produced under the pressure of30MPa with different temperature of350°C, 375°C and 400°C. The stability existing area of possible cerium compounds and different ions like Ce2+,Ce3+,Ce4+,W,HO2-,0ff ,CeOH2+,CeO+ and CeO2· were determined.IntroductionCerium is an extensively used metal element playing an important role in the rare earth elements. CeO2 is an apparently simple binary oxide with cubic fluorite structure [l]. Ce0O gives rise to a range of important technological applications because of its oxygen storage capacity at moderate temperatures as below: CeO2=CeO2.x+ X/2O2 [2]. The oxygen storage phenomenon gives ceria important technological uses in different fields as automobile exhaust purification catalyst [3-4], fluorescent powder, ultraviolet absorption material [5], polishing powder, fuel cell materials [ 6], and gas sensors, etc. The excellent properties of CeO2 nano powder make its synthesis and preparation become one of the hot spots of world scientists study."

Jan 1, 2013

By C. J. Alberts

The perception exists in many organizations that, once an energy management system is employed, there need not be any further adjustments to such a system. This is not true, as the field of energy management is a dynamic field, and constant feedback and adjustments are needed to enhance the efficiency of a system to the point that substantial pay-back can be obtained. It is stressed that for any energy management system to be successful, careful planning should permeate through the organization, from the top level decision-makers to the workplace. This paper describes a dynamic technique by which energy management strategies can be evaluated by viewing the effects of the strategies on the organization as a whole.

Jan 1, 1997

By Jean-Pierre Nossereau, Allen J. Hulshizer

The main thrust of this paper covers the design, installation techniques and experience associated with the installation of eleven 1.5 m (4'-11") and three 2.87 m (9'-5") diameter shafts in 15 to 23 meters (50 to 75 ft) of water over 1.6 Km (a mile) out in the Atlantic Ocean. The approach implemented, permits the use of pre-fabricated shaft linings and incorporates a safe dry-tap method for connecting the offshore shafts to tunnels driven blind from deep land shafts over 4.8 Km (3 miles) away. This tunnel-shaft system is a unique venture employed at the Seabrook Nuclear Power Station to meet plant cooling water requirements.

Jan 1, 1981

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

By Alana Pereira Ramos, Walman Benicio de Castro

Amorphization and martensitic transformation (Ms) characteristics of Ti–Ni-Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the wheel linear velocity from 21 to 63 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate and alloy composition on martensitic transformation behavior is discussed.

Jan 1, 2015