Search Documents

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By F. R. Joubin

MR. CHAIRMAN, Members of the C.I.M., and Friends -particularly friends, because I am not entirely a stranger in your city. I was last here some five years ago and it has given me a great deal of pleasure this evening to be able to say "Hello" again to those I had met at that time, when Bourlamaque and V al d'Or were very busy centres of intensive and successful gold exploration. My remarks this evening have to .do with Canada's Place in the Atomic Age. They will be of a general nature but I hope to tell you ?enough to whet your appetite so that you may be provoked into per-.suing the subject further. Now, atomic developments have become quite commonplace. Words like radioactivity, reactors, nuclear fission, and so on are known to everyone, even the youngsters. I re-member two or three years ago one of my office boys came to me and said "Mr. Joubin, I would like a raise." I gave the request a few seconds of serious thought and finally said "Alright, Jimmy, we'll give you a raise." However, he made no effort to leave, so after a -couple of seconds more I said, "Is there something else ?" and he said "Yes, Mr. Joubin, could you make that raise 'radioactive' to the first .of the year ?"

Jan 1, 1958

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By E Hernandez, I Agustian, W Kusumohastuti

PT Freeport Indonesia is completing the first underground gyratory crusher excavation at their Deep Mill Level Zone (DMLZ) mine located in the mountains of Jayawijaya, District of West Papua, Indonesia. DMLZ is an underground block cave mine with an expected output of 80 000?t/d and a scheduled production start in 2015.In order to deliver crushed ore to the mill through the existing conveyor belt, the DMLZ block cave mine will construct two 1000?kW 1.6?×?2.3?m gyratory crushers with their own respective ore flow conveying systems underground. Each crusher is composed of top, middle, and bottom chambers with an ore bin. This system includes a series of high capacity conveyors approximately 5 km in length including transfer stations and support facilities.The development methodology required a combination of lateral development by jumbo drilling machines and vertical development by mechanised raise climbers (MRC) due to the complexity of the chamber design.This paper will discuss the project scope, design and development methodology, ground conditions, innovative survey controls, and the challenges faced due to the remote location.CITATION:Hernandez, E, Kusumohastuti, W and Agustian, I, 2014. Excavating the first underground Gyratory Crusher at the Deep Mill Level Zone mine, PT Freeport Indonesia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

Mining operations adopt a variety of measures to combat dust underground. These include ventilation systems, water sprays, physical barriers, and personal protective equipment (PPE). Respirators are a class of PPE that can provide clean particulate- free air to the users. Powered Air-Purifying Respirators (PAPRs), used commonly in medical and other sectors, are not prevalent in the mining industry. PAPRs use P100 filters that have 99.97% dust capture efficiency. We present our results from computational fluid dynamics (CFD) simulations performed to understand the impact of a PAPR on airflow and dust particle concentration in the vicinity of a miner. These results show that donning PAPRs can lower the miners’ exposure to respirable coal dust in their workplace.

Feb 1, 2025

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By Roorda H. J, R. R. Saddington, Curlook W

THE copper-nickel sulfide ore deposits of the International Nickel Company of Canada, Limited contain the minerals pyrrhotite, pentlandite, and chalcopyrite. In the extraction of the nickel, copper, and iron, much of the processing involves oxidation of the metals as well as sulfur. Roasting plays a predominant role at several stages in the operations which prepare the constituent metals for refining. Copper, nickel and iron concentrates of various grades, ranging from low-grade nickeliferous pyrrhotite to high-grade nickel sulfide, must be partially or completely oxidized. Figure 1 shows the main points at which roasting is conducted at INCO. Roasting experience at INCO dates back to the time when lump ore was partially roasted in heaps. It has progressed through single hearth roasters, sinter machines, multiple-hearth roasters, flash roasters, and more recently has centered on the development and utilization of fluid bed roasters. The primitive, slow, and inefficient method of heap

Jan 1, 1961

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By A. Galibois, A. Dubé, H. Monette, J. L. Collins

"The start of mining operations often raises serious financial problems. In marginal cases promoters frequently demand financial aid from governments.In the past, the financial assistance has taken the form of gifts, procurement contracts, etc., but aid in such form has been severely criticized. A new formula has been developed to provide a more equitable distribution of the revenues accruing to the government and to private capital.The benefits to these two parties have been evaluated in an hypothetical case and compared in terms of internal rates of return on their investment, their shares of the undiscounted cash flows and their primary profits.The method based on the non-zero sum game theory provides a means for suggesting the lowest feasible annual production and the optimal sum contributed by the government in the form of outright gift, equity capital and convertible bonds. Other financial hypotheses can also be optimized by the computerized analysis."

Jan 1, 2014

By Yimin Zhu

This paper introduces the sixteen mappings and rules of mineral flotation and the subgroup, period etc in periodic table of chemical element to provide mineral flotation workers to refer in theory and practice research. the nine mappings and rules of mineral flotation and the subgroup, period are Saline minerals including the first main groups and collectors of aliphatic acid and aliphatic amines, Minerals including the second main group elements and collector of aliphatic acid, Hydrated ion of the second main group elements and quartz flotation, The floatability of oxidized minerals including the four main group elements, Organic acid including the fifth main group elements and wolframe, tin flotation collectors, The floatability of sulfide minerals including the fifth main group elements, Inorganic compounds including the seventh main group elements and mineral flotation regulator, Oxidized minerals including the forth Subgroup elements and organic flotation agents with phosphorus and arsenic, Oxidized minerals including the fifth subgroup elements and organic floating agents including the fifth main group elements, Minerals including the first subgroup elements and CN-, Sulfide minerals including the second subgroup elements and CN-, The effect of the highest N-valency inorganic acids or salts including p area elements of the third period in mineral flotation, Oxidized minerals including transition elements of the forth period and 3# flocculating agent, The floatability of minerals including elements of the sixth period, Element area of generating compositions and the collecting theory of mineral flotation and so and. Keywords: mineral flotation, periodic table of chemical element, subgroup, period, regulator, coordination chemistry

Sep 1, 2012

By R Moreby

This paper is a demonstration of the techniques developed during an Australian Coal Association Research Program (ACARP) funded research project aimed to develop aids, principally computer based, to assist mine personnel to more efficiently manage significant incidents in coal mines. These aids include software to aid in the location of the incident, electronic information storage and retrieval, online site emergency response manuals and software to aid in decision-making.

Jan 1, 2005

By J. K. Whyatt

The Bureau of Mines, under a cooperative agreement with Callahan Mining Corp., measured rock displacement at the 4,7S0-ft level of the 5,100-ft-deep rectangular, timbered Caladay Shaft in northern Idaho. Displacements were measured with multiple-position borehole exten-someters (MPBX) installed 4 ft above the face and timber extensometers (TE) installed with the timber sets. This report presents the displacement data along with preliminary, qualitative observations of rock behavior. The measured displacements showed an instantaneous response to shaft sinking and significant time dependency. The relative magnitudes of displacement measured at the shaft walls were heavily influenced by local geologic structure and distance from the shaft bottom.

Jan 1, 1987