Search Documents

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By Bruce W. Gonser, A. U. Seybolt

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By A. U. Seybolt, Bruce W. Gonser

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By Mckenzie CK

Delay scatter, although widely recognised, has rarely been studied with the aim of critically reviewing blast designs. With current trends towards increased deck charging, and the effect on the number of separate delays in blast designs, delay scatter is shown to have a rather profound influence on the control of initiation sequence and the ability to successfully con- duct pre-splitting and smooth blasting. Determination of realistic delay scatter distributions is the first step towards application to blast design. Delay scatter must be evaluated in terms of deviation from the nominal time, not in terms of deviation from the batch mean, since the latter is not usually known without specific testing, requiring accurate timing instrumentation. Computer programs using Monte Carlo simulation can then be developed to investigate the probabilities of out-of-sequence initi- ation or near-simultaneous initiation within any specified interval. The procedures have been applied to both production and development blast designs in Australia and Chile to improve initiation sequence control and to rationalise and simplify blast designs.

Jan 1, 1988

By S. Q. Yang

Rotary radial jet improves greatly the pulsing velocity of airflow along each direction everywhere in the entry, intensifies transverse migration of air, eliminates effectively the local gas accumulation, and distributes methane concentration in airflow evenly and rapidly. According to the theoretical analysis of heat-transmission, mass-transmission and momentum-transmission, not only the similarity between heat-transmission and momentum-transmission, but also the similarity between mass-transmission and momentum-transmission exists in turbulent flow field, When the analogical equivalent ratio of heat transmission and mass transmission meets a certain criterion and remains a certain value, the temperature field can be used to simulate the methane concentration field. After hot airflow being released, thermograph instrument can be used to monitor the changing patterns of heat transmission and temperature distribution which simulates the changing patterns of methane transmission and methane distribution respectively. By analyzing these patterns and parameters of airflow field and methane distribution field during the process of local gas accumulation discharging by rotary radial jet, the dependability and validity of this discharging method are tested and verified.

Jan 1, 2004

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

On-line radioisotope gauges determine information on the characteristics of ore to enable improved control of processing operations. In the metalliferous mineral industry, in-stream analysis systems based on radioisotope X-ray techniques determine concentrations of valuable minerals at various stages of the concentration process. In the coal industry, on-line gauges determine ash and moisture contents, and the specific energy of coal.In-stream analysis systems developed in Australia are installed in about 30 mineral concentrators. Their use has led to the increased recovery of valuable minerals, and the time taken to recover the cost of installation is usually several months. The savings to Australia resulting from use of these analysis systems is estimated to be more than $A 15 million per year.Australian experience in the training of mineral industry personnel shows that the most effective approach is to combine courses on nuclear techniques and control of processing operations. This is the basis of Australia's contribution to the minerals sub-project of the United Nations Development Program (UNDP) Industrial Project.

Jan 1, 1985

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By W R. Hancock

Control of complex machinery through the internet is investigated through the construction of a vehicle prototype developed using off-the- shelf hardware. The vehicle was able to be controlled remotely through the use of a client side interface connected to a steering wheel and foot pedals. By attaching sensors to the vehicle, data could be collected from which one could infer the effectiveness of such a control system. The effect of latency on control was monitored by the introduction of an artificial latency, simulating a wide variety of internet-related issues, such as unstable connections and dropouts. Sensor data could then be used to gain an understanding of how the system could be improved though either control or interface design. A path tracking experiment was conducted to gather controllability data and it was found that such a system is plausible within a reasonable range of latencies. It is expected an area of future research would be an extension of this current project, applying the information gained to real world control systems.

Jan 1, 2008

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

By W. A. Naismith, R. T. Pakalnis

The Umgal a section of the We1gedacht Exploration Company Ltd., a member of the Rand Mines Group, is situated near Utrecht in the province of Natal, South Africa. Two coal seams, the Alfred and Gus, are mined to fulfill commitments to both inland and export markets. To increase extraction in the high quality Alfred Seam, pillar extraction, known locally as stooping, was introduced to the mine in September, 1980. Mining is a conventional cut-drill -blast operation and takes place under a unique set of geological conditions viz. moderately thick seam at 3.5 m; rapidly varying cover from 25m to 120 m; an overburden containing competent sandstone and dolerite horizons. In order to improve the understanding of the manner in which the pillar and overburden interact during pillar extraction, a largely visual system of monitoring backed up by roof-floor convergence measurements was employed. Preliminary analysis of the observations suggests that roof collapse or goafing occurs in three phases but is only initiated once a critical amount of convergence has taken place.

Jan 1, 1983

By S D. Golding, K Baublys, V Nanjappa, C J. Moran

Water reuse is becoming an integral component of the water management strategy on mine sites. This practise is being driven by corporate sustainability goals, community and societal pressures to demonstrate improved water stewardship, as well as climate and regulatory pressures. However, water reuse often results in water quality compromise which can then result in decreased recovery through problems in processing circuits, product quality, and an increased likelihood of discharge of water that cannot meet environmental regulatory requirements. On most mine sites, there is usually a disjuncture between water quantity management and water quality management with the latter being managed solely as an environmental problem. It is becoming increasingly clear that water quality and quantity must be managed as an integrated system. In order to integrate water quality and quantity management to achieve multiple objectives the dynamics of water and constituents must be understood. Using examples from a study being conducted at a coal mine in the Bowen Basin, this paper will outline the dynamics of water and salts on the site.

Jan 1, 2009

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

By Marshall B, Gee R. D

Geological data processing by machine enables'an increased rate of coverage, better supervision and control of field programmes, increased effectiveness of field operators, and vastly improved access to old and new field data. Even a system of restricted felxibility enables a mapping programme to be organ- ized and conducted independent of personnel changes, whilst elimination of much compilation time increases the rate of cover- age such that it relates to mode of transport and geological complexity rather than to personality factors. A machine is useful only if applied to tasks suited to its capabilities, and must be aimed at those types of mapping in which a limited number of attributes adequately define the problem, and the data is of a form suited to coding and is normally collected in sufficient abundance to make compilation wearisome. Machine systems are therefore unsuited to most types of lithological mapping and to most types of exploration in new areas, but have proved useful in many branched of cartographic geophysics (e.g. gravity and magnetics), and in cartographic Geochemistry.

Jan 1, 1969

By J. T. Vehkala, S. S. Kerr, D. E. Robertson

"Since the late 1970s, extensive work has been carried out at Placer Dome Inc. 's Dome Mine to develop new mining methods and equipment to improve the productivity of narrow vein mining (Mining Magazine, Oct. 1986, pp. 308-317; Mar. 1988, pp. 176-/79). This work has been focused on mining veintype deposits varying from 0.9 m to 1.5 m in width using open stoping and cut-and-fill mining methods.In 1989, the Dome Mine entered into a contract with Ram Raising Ltd., a joint venture company of Angus Martin and I.S. Redpath Ltd., to develop and mine a narrow vein test stope using an Alimak Raise Climber. Early results have been favourable, indicating that Alimak methods can be used successfully to mine narrow vein are.HistoryThe Dome Mine, which has been in continuous operation since 1910, is located in South Porcupine, part of the city of Timmins, Ontario. The mine is wholly-owned and operated by Placer Dome Inc. and is part of Placer Dome Inc.'s international stable of of 19 mines."

Jan 1, 1990

Since the initial development and trials of FLEXIBOLT flexible roof bolts, further comparative testing and product development has been completed as part of the changeover to this roof support system at two Australian longwall operations, Ellalong and Angus Place Collieries. Details of the practical implementation of FLEXIBOLTS at both collieries are outlined together with their impact on roadway development rate productivity. At Ellalong where fully encapsulated 2.1 m long bolts are used, the reduction in bolt density is discussed with respect to both support system design and work force acceptance. The impact of shear deformation on bolt loading is described. Bolts longer than the working height have been required at Angus Place to achieve a suitable bolt anchorage horizon. Details of the long hole drilling and the benefits of a two stage grouting procedure are outlined. Improvements in roof conditions which have resulted from the inclusion of FLEXIBOLTS into the overall roof support strategy at Angus Place are described. Their importance to the viability of the Angus Place operation is also highlighted.

Jan 1, 1994