Search Documents

Ore from the Hill 50 Gold Mine, consists essentially of pyrrhotite, with minor amounts of pyrite, chalcopyrite, galena and gold, replacing "jaspilite." The gold is associated with the sulphides as shotty particles. About 8 per cent. of the particles are less than '0.010'mm.The Hill 50 Gold Mine, at Boogardie in the Murchison goldfield, about 300 miles north-west of Kalgoorlie, was first operated in 1898. From 1898 to 1917 it yielded 20,000 short tons of ore for a recovery of 6,225' fine oz. gold, equivalent to a recovery grade of 6.22 dwt. gold per ton.The present company since the beginning of its operations in September 1936 to June 30, 1954, produced 811,081 short tons of ore for a recovery of 242,554 fine oz. of gold, equivalent to a recovery grade of 5.98 dwt. gold per ton.The grade of ore (recovery grade) has shown a remarkable variation with depth. From the 120 ft. Ievel to the 300 ft. level, it averaged about 7.5 dwt. Au per ton. Below the 300 ft. level it declined, and from 300 ft. to 400 ft. averaged 4.9 dwt. per ton, falling further with increasing depth to about 4.5 dwt. per ton at the '600 ft. level.On the 820 ft. level the grade improved sharply to about 14 dwt: per ton, and this grade has persisted down to and on the 1060 ft. level.The orebody has been described by Finucane (1953) as a series of lenses of finely banded jaspilite conformably enclosed by greenstones. The jaspilite is tightly folded and faulted and intruded by dykes of felspar porpnyry.Mineralization is practically restricted to the jaspilite.

Jan 1, 1955

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By C. A. Carroll

In February of 1989 the Mission Complex of ASARCO Incorporated completed an expansion of its concentrator, raising the base mining rate from 25,900 TPO (28,500 STPD) to 37,200 TPO (41,000 STPD). The expansion was accomplished by extending the twelve existing Mission ball mills in length, by installing the grinding circuit from Asarco's idled Sacaton Concentrator along with various auxiliary equipment, and by modifications to the flotation circuit and water systems. This paper will give a brief history of the consolidation of the ore body which made the expansion possible and explain the various parts of the expansion.

Jan 1, 1990

By A Bax, G Wardell-Johnson, W P. Staunton, J McGrath, J J. Eksteen

Since 2001, the AMIRA P420 gold processing technology project series has been studying the recovery of gold using gravity devices, with particular emphasis on the centrifugal units, Knelson and Falcon concentrators. The work has entailed the surveying of operating gravity circuits in Australia, Africa and North and South America.This paper reviews some of the results and lessons of these studies, including common circuit operating and design factors, which limit gravity recovery; pointers towards effective modelling of gravity circuits; and the contribution of gravity to overall gold recovery.CITATION:Wardell-Johnson, G, Bax, A, Staunton, W P, McGrath, J and Eksteen, J J, 2013. A decade of gravity gold recovery, in Proceedings World Gold 2013 , pp 225-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Paolo Ciambelli, Lenore Rainey

"The evolution during oxidation of the internal structure of soot and carbon black particles was studied using high-resolution transmission electron microscopy (HRTEM) and an image analysis system. Increasing ordering to the carbon structure with increasing oxidation is observed. Measures of the increased order are increases in the fractional coverage of a cross section of the particles with a layered structure, a decrease in the mean interlayer spacing, and a decrease in the spread of the interlayer spacing. The changing structure of the carbon black impacts its properties, such as the rate of oxidation.There is considerable interest in the study of the structural changes of carbonaceous materials as a function of oxidation. Davis et al.1 measured the variation of carbon dioxide surface area of various coals as a function of residence time in a flow reactor. HRTEM measurements revealed that crystallite dimensions and interlayer spacings are altered by combustion. Ishiguro et al.2 showed that oxidation alters the structure of diesel soot. The aim of our current research is to develop a better understanding of the microstructural reordering of carbon blacks with implications to their properties. The carbon blacks used in this research have already been studied and their reactivities as a function of oxidation measured.3The methodology used in this work has already been described in detail elsewhere.4 This paper presents an application to quantify the structural changes of carbon black particles as a function of oxidation and graphitization. The technique used is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, chars, etc., possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure. The carbon structure has been variously described as turbostratic5 or as crumpled sheets6 to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as the composition of the source of the carbonaceous material. The value of electron micros¬copy in studying the morphology of such materials has been well established,2,7,8 although only a few attempts toward quantification have been made.The sample observed was carbon black CB330 from De¬gussa. One set of carbon black samples were oxidized in a thermo-gravimetric analyzer (TGA) in air at 575 0C, so that the conversion varied from 0 to 96%. Another set of carbon black samples were graphitized (Graphpac-GB by ALLTECH) and then oxidized in the TGA at 680 °C until 92% burnout was reached. The latter samples are called GB 0% and GB 92%, respectively.For the HRTEM observation a small portion of each sample was ultrasonically dispersed in ethanol. The suspension was deposited dropwise on a copper TEM grid coated with a lacey carbon film. The examination of the samples was carried out on areas that extend over the holes in the supporting film in order to avoid interference from the amorphous carbon background film An oriented gold crystal was used as a calibration standard and subjected to the same techniques as the carbon black samples."

Jan 1, 1998

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus. The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn304) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6.7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn304 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10-5 m2/s range. The pore size was mainly between 0.1 and 10 um.

Jan 1, 2003

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus, The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn3O4) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6,7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn)04 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10.5 m2/s range. The pore size was mainly between 0.1 and 10 um,

Jan 1, 2003

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Daniel Roy, Danielle Bouffard, Antoine Berton, Simon Gariépy

Commissioning a mineral processing plant has always been a challenging task. The process includes pre- operational verification, dry and wet commissioning, and a gradual ramp-up to full production, all of which must be executed within the shortest possible timeframe, requiring numerous highly interdependent tasks to be conducted concurrently. This phase is under scrutiny by shareholders, corporate management, and other stakeholders who are keen to see a return on investment as the operation starts yielding results. Despite extensive documentation in the literature highlighting its significance, the impact of the commissioning phase remains underestimated in contemporary mining projects. This paper provides an overview of the commissioning process and its associated challenges before focusing on a critical success factor: building a dedicated commissioning team with the required competencies and personality profiles. The roadmap to achieving an efficient plant start-up is outlined. Drawing on over 15 years of experience with more than 20 concentrator commissioning and start-ups, a general framework is presented to maximize success. This method emphasizes the crucial role of the operation and metallurgy team in supporting these projects. Finally, insights from Soutex’s involvement in multiple start-ups are shared, offering lessons learned that emphasize best practices and challenges encountered in expediting the ramp-up process while maintaining high Health, Safety, and Environment (HSE) standards.

Feb 1, 2025

By Johnny Zhang, Yang Anguo, Li Weifeng, Xueyi Guo

"SKSTM oxygen bottom blowing smelting technology was developed by SKS-ENFI at SKS Smelter, Hunan in the 1990s to replace the conventional sintering process and thus to meet the high national EHS standard for lead.Since then, two major milestones have been achieved:1. Since 2002, the SKS oxygen bottom blowing smelting-blast furnace reduction has been in operation at SKS, YGL, Chizhou smelter etc. Now in China, about 50% of the lead (4.2 millions t/year) is produced using SKS process; and2. Since 2008, the blast furnace has been replaced by direct reduction of molten rich lead slag at YGJ smelter, which is more energy-efficient since no slag cooling is required. This two stage process (SKS Oxidation- Direct Reduction) is named as the YGL process.Since 2008, numerous technological innovations have been implemented in the furnace design, process control, and maintenance at YGL. The plant has been successfully demonstrated its unique excellent performances on all aspects from processing capacity, product quality, energy reduction, cost reduction and emission reduction. The purpose of this report is to update all the improvements with proven tracks.Meanwhile, a preliminary comparison on the following aspects between the YGL process and other similar technologies has been discussed:1. Plant design and operating conditions;2. Mass and heat balances, metal (Pb, Ag) recovery;3. Consumables, oxygen gun and refractory lining life;4. Energy consumption and operating costs;5. Sulfur capture and emission reduction etc.It is concluded that the modified SKSTM process is a clean SO2-free emission process. The process is characteristic of other features such as no extra fuel addition, low capital with a small foot-print design, low OPEX, high throughput, easy operation, long refractory lining life and high productivity (95%+ on line time annually). It offers an alternative cost-effective technology for lead smelting industry."

Jan 1, 2014

By M. H. Caron

THE most outstanding property of ammonia liquors, used in the ammonia leaching process is their very limited ability to dissolve all compounds present in reduced ore except nickel and cobalt. Although they do have such a high degree of purity, even the smallest amounts of impurities contaminate the precipitate of basic nickel carbonate that may be obtained from pregnant liquors by straight distillation. Figures have been given in a separate paper regarding the extent of such contamination. The product of straight distillation is likely to contain small amounts of Fe, Mn, MgO and SiO2 as well as some sulphate and sulphide. The sulphur can be readily eliminated by calcination of the product at the proper temperature and MgO and SiO2 by reduction and melting of the metal with a suitable flux. After such treatment the metal is relatively pure, and the iron and manganese content will be very small. The cobalt content, however, may vary considerably, depending upon the ore treated. The metal obtained from pure true garni-erite ores usually has only a small cobalt content of less than 1 pct. Metal obtained from medium grade iron-rich nickel ores may show cobalt values from 2 to 3 pct, and the alloy obtained from laterite is likely to contain as much as 10 pct cobalt. By proper treatment a good deal of cobalt may be recovered from lateritic nickeliferous iron ores, and cobalt will become the major constituent of the pregnant liquor if asbolan ores or similar products are treated. The pregnant liquor of "run of mine" nickel ores may have a pinkish shade, indicating the presence of cobalt. It is evident that from such liquors the metals should be recovered separately. Even if cobalt is present in only very small amounts, it would probably be economically justifiable to recover both metals as pure as possible if a suitable process could be devised. The author has made investigations along this line and has patented some processes adapted to the treatment of this type of solutions. Selective Dissolution of Nickel from Basic Nickel Carbonate Containing Some Cobalt: Basic nickel carbonate obtained from true garnierite ores by straight distillation of the pregnant liquors, always contains some cobalt as well as the normal impurities. In. order to improve the quality of the nickel product and to recover most of the cobalt, the following process has been devised. By using liquors with a low CO2 to NH3 ratio, nickel can be redis-solved preferentially to cobalt. It is not a sharp and clean separation but a selective one, for the bulk of the nickel may be redissolved with a small amount of cobalt, and a small residue may hold the bulk of the cobalt. The greatly increased cobalt content of the residue is indicated by a pronounced olive green color, in contrast with the light green color of pure basic nickel carbonate. The following example is given from Dutch patent No. 52788, Klasse 40a. 43 granted June 17, 1942: The original precipitate contained about 0.55 pct cobalt calculated on total nickel + cobalt. Eight hundred and fifty grams of the basic nickel carbonate were redissolved in leach liquor containing 7.12 pct NH3 and 2.12 pct CO2. The weight of the dry residue was about 3.5 pct of the original weight. By analysis it was found that the residue contained: Fe 1.93 pct, Co 6.01 pct, Ni 34.87 pct and also a certain amount of silica. The clear filtered blue liquor was distilled and the precipitate of basic nickel carbonate from this analyzed: Fe 0.008 pct, Co 0.0146 pct, Ni 42.37 pct. It is obvious that this product is considerably more pure, since calculation shows that about 94 pct of the original cobalt remained in the residue. Cobalt and nickel can be recovered by further

Jan 1, 1951

By R. I. Lahring, C. G. Inks

A surfactant waterflood, using a block copolymer of ethylene and propylene oxide (PLURONIC L64*), wa., started in 1956 in Kansas to determine the commercial feasibility of such a process. The production formation was the Bartlesville sand at a depth of 1,400 ft. Leares in the test area had attained both primary and secondary production peaks, and were on a normal decline when the tests were initiated. The injection wells were taking water at a reasonable pressure and none of the operating conditions were particularly unusual. The leases were selected primarily because of normal operating conditions, and not because of any serious problems demanding remedie>,. Oil production and water injection data were recorded during the 10-year test period, and their compilation indicates that the surfactant resulted in an increase of about 9 percent in secondary oil production. Other benefits derived from the surfactant injection were lower injection pressure that resulted in reduced power consumption and reduced erosion of the pumps; and lower calcium scale buildup. These fringe benefits more than offset the cost of the surfactant used. Introduction During the past several decades, considerable research has been carried out on secondary recovery of crude oil that remains in the producing formation despite the most efficient, current primary production practices. Methods are constantly sought of increasing recovery of oil, while at the same time improving the economic efficiency of operations. One method that has received intensive study over the years is the use of a surfactant as a waterflood additive. Laboratory tests show conclusively that dilute solutions of surfactants remove considerably more oil from uncon-solidated sand cores than does water alone.'- The loss of surfactant by adsorption at solid-liquid interfaces has caused serious doubt that surfactants can be used economically as waterflooding additives. This is especially true with anionic and cationic surfactants, and to a lesser extent with nonionic surfactants. This work was undertaken to determine the effectiveness in increasing oil production by injecting water containing small quantities of a nonionic surfactant. The surfactant selected was PLURONIC L64*, a block copolymer based on ethylene and propylene oxide, having the following structure The selection of the test site, a typical shoe-string sandstone type of field located at Batesville pool, Toronto District of Woodson County, Kans., was made because of its normal primary and secondary recovery operating conditions, and not because of any serious operating problems. When the tests were begun, the field was experiencing the customary post-peak production decline of a waterflood. Using for the tests a field that was on a normal production decline, while maintaining constant all variables other than the addition of the surfactant. was of varamount importance if success or failure was to be attributed to a particular cause. It was reasoned that if a surfactant was added to the injection waters and nothing else was done to influence the oil production or injection of water, the effects of the surfactant on the flood could be determined precisely. Production History The first well in the tested field was drilled in 1935. Gas repressurization began immediately, but it was not until Aug., 1938, that the major portion of the field was developed. During the period of repressurization, 1,700 MMcf of gas was injected. As can be seen from the curves of Fig. 1, the production peak from gas injection was attained in 1937 and a normal production decline followed. Early in 1942, water injection wells were drilled and injection of water Was initiated. The amount of water injected increased as more injection wells were drilled until a peak injection rate of 2,700 BID was reached in

Jan 1, 1969

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016