Search Documents

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un- roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence.

Jan 10, 1957

By Akira Ishizu, Nobuo Matsui, Tatsuya Nagahama

In the concentrator of Kamioka Mine, lead-zinc bulk differential flotation is practiced. It results in three kinds of thickener over- flow, namely; tailing, lead concentrate and zinc concentrate, which are discharged as wastewater. Since these three kinds of overflow differ from each other in water quality, they are separately recycled to appropriate processes based on their water quality. The tailing and the lead concentrate thickener overflow are directly recycled to their respective suitable processes. However, as the zinc thickener overflow contains Cu(CN)3--, ZnS, CdS, CN-, xanthate and frother, the total zinc thickener overflow cannot be recycled at one time to any one process without creating harmful effects. Consequently, all the ingredients in the zinc thickener overflow other than CN- are floated by Ion-Precipitate-Ultrafine-particle flotation, using Nagahm flotation machine. After this treatment, the zinc thickener overflow, containing only CN-, is effectively recycled to the lead-zinc differential flotation circuit. Thus the integrated recycling of waste-water greatly reduces environmental problems, and in addition it generates a sizeable profit by improving overall mill recovery, and permitting the reduction of reagent consumption.

Jan 1, 1976

By A. J. Weinig

THE Liberty Bell cyanide precipitate is unique in that it is apt to vary widely in composition in the course of very short, periods of time, and a method of refining and melting that would prove highly satisfactory at one cleanup would yield almost an hopeless "mess" it a second. Table I gives a general conception of the wide range in grade and composition of those raw precipitates. It is evident that no one standard flux could be expected to produce a high-grade bullion with such a widely variable precipitate, and that any method of treatment with acid requires most careful consideration. Refining by Acids Naturally, our first efforts to improve our precipitates were directed along the lines of acid treatment. Table II embodies the results of careful sampling and analysis of one cleanup at the time when wet refining reached its maximum development at this mill. We have now discarded all methods of wet refining, successfully replacing them by amore scientific method of flux calculation described herein, but it is believed that a general description of this wet refining is warranted as it throws some interesting side lights on acid refining in general.

Jan 3, 1916

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By D Cohen, A Wurster

Many Southern African mining operations produce mine water which is beneficially and productively utilised on the mine sites and to support other water uses. Mine water treatment typically takes place within the context of integrated mine water management involving pollution prevention, waste minimisation, recycling and reuse as well as river discharges. Development of new and improved mine water treatment has focused on the neutralisation of metals removal, desalination of high sulfate waters and passive treatment. Mine water neutralisation processes now incorporate a combination of natural limestone and lime treatment, as well as features to maximise gypsum precipitation. The South African CSIR developed a suite of limestone-based neutralisation processes, which include reuse of CO2 and CaCO3 generated in the process. Desalination of high sulfate mine water is typically done using one of the following technologies:biological sulfate removal with different approaches to the handling of the sulfide generated in the process, and ultrafiltration (UF)/reverse osmosis (RO) treatment with different approaches to the handling and disposal of the brine. The current research and development focus is the separation and recovery of saleable products from the treatment residues and brine streams.

Jan 1, 2006

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By Gregory J. Chekan

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating multiple seam interactions associated with longwall mining. Longwall gate entry and panel stability have been influenced by previous mining in coalbeds above and below a mine in Virginia that operates in the Lower Banner Coalbed. Directly superjacent, approximately 115 ft, the Upper Banner Coalbed has been partially worked by room-and-pillar mining. Directly subjacent, approximately 730 ft, the Tiller Coalbed has been worked by partial room-and-pillar retreat mining. The study mine has experienced problems during development of gate entries in areas of overmining and undermining. It is anticipated that stress fields associated with adjacent mining may further affect gate entry stability and face advancement during the extraction of the longwall panel. To assess overmining and undermining effects on ground stability, the Bureau gathered geotechnical information at the site. Headgate entries and pillars were instrumented and monitored to study loading behavior as the longwall face approached and passed potential problem areas. Measurements indicate that although increases in average pillar pressure were greater than predicted values, previous mining in adjacent coalbeds had little effect on headgate stability.

Jan 1, 1989

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By Walter Valery, Sergio Vicuna, Roberto Valle, Hamer Arevalo, Ben Burger, Lui Vargas, Alex Jankovic, Jim Seidel, Eduardo Nozawa

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha’s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32’ x 32’ EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By Russell Frith

The paper defines the various operational advantages associated with the use of cribless tailgates during longwall extraction and considers the associated ground control issues that need evaluating to ensure a successful outcome. Reference is made to longwall mines in Australia currently using cribless tailgates and the geotechnical and ground support factors that allow them to do so This includes the nature and behaviour of the roadway roof the stability of the chain pillar and also the type and timing of installed support A specific case history from a colliery in NSW will he referred to whereby heavy standing support was replaced with lower density tensioned cables as routine TV secondary support, which resulted in both improved TG roof conditions and a significant cost reduction. The conclusion will be drawn that cribless tailgate roadways can potentially he used in many environments either due to the existence of highly competent immediate roof conditions or through the appropriate application of active reinforcing support measures in less competent conditions. Use will he made of Strata Engineering?s roof behaviour and stability model in demonstrating the various concepts involved.

Jan 1, 2000

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By John G. Hall

MANY millions of tons of raw materials are removed each year from open pit mines in the eastern U. S. These materials are used by industry to produce aluminum, asbestos, barite products, building stone, cement, crushed stone, copper, coal, dolomite, garnet, iron, limestone, mica, phosphate, phyrophyllite, titanium products, and wollastonite. Improvements in open pit mining techniques through the years have made open pit mining more and more attractive as compared to underground methods. Today ore deposits that formerly would have been mined underground have proven to yield more profit if mined by open pit methods. Ever-rising labor and material costs have made equipment capable of high-volume production and low-unit cost-and supplies rendering low-unit costs-not only attractive to open pit operations, but essential to their economic existence. During the past year, the major advances have been in drilling and blasting operations, and the application of large capacity materials handling equipment. Mining men from the Great Lakes, Northeast, East Central, and Southeastern regions of our country tell in the following articles of the trends in open pit mining in their areas during 1956.

Jan 2, 1957

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By Ben D. Thompson

Cemented Paste Backfill has proven to be of critical importance to the operation of a number of Canadian mines, primarily due to the rapid backfilling rate this method permits. In order to improve the efficiency of this backfill system (i.e. optimize binder contents, fill fence design, and the employment of two stage filling strategies) there is a requirement to better understand its geomechanical behaviour. In response, in-situ experiments have been conducted in long-hole stopes to quantify the evolution of total earth pressures and pore pressures at a series of instrumented points within both the core of the backfill and close to fill fences. The deflection of fill fences as a result of paste loading has been measured and additional instrumentation has also been employed to measure cement hydration, negative pore pressures, and blasting induced vibrations within fresh and cured paste backfill. Installing geotechnical instrumentation within an open long-hole stope can be an extremely complex procedure and this paper details the methods that have been successfully employed. Preliminary results are presented, and the pressures induced by backfill with differing binder contents, at a number of different in-stope locations are considered.

May 1, 2009

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By Debra F. Laefer

Jet grouting is a ground improvement technique that has become widely adopted over the past three decades, yet relatively little data has been published about performance characteristics of mixes under adverse conditions, such as the inclusion of clay lenses. This paper presents an experimental investigation on the impact of clay on the strength of jet grouting. A total of 150 grout samples were subjected to 0-10% levels of Kaolinite and Bentonite inclusion. While the Bentonite was introduced as a pre-hydrated slurry, the Kaolinite was mixed in two ways: in a pulverized condition and as large chunks. Sample strength and stiffness were measured at multiple dates within the first 28 days. With 10% clay inclusion all samples exhibited significant strength and stiffness losses. With some, substantial losses began with as little as 4% clay. Even a 1% clay inclusion tended to decrease strength and stiffness between one-quarter and one-third of the control sample. Depending upon clay type and inclusion method, results differed significantly with respect to strength and stiffness development and failure mechanism. Petrographic analysis is used to provide further insights as to apparently divergent behaviors.

Jan 1, 2009

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By R. W. Stahl, H. E. Sanford, J. B. Benson

Immediately following the capitulation of Germany in World War II, the German State was occupied by various allied forces, who supervised all indus- trial activities in the area. Coal production is vital to the industrial life of Germany, and most of the coal is mined in the American- and British- occupied zones of western Germany. The British-occupied zones include the Aachen and Ruhr districts, from which approximately 90 percent of the coal is obtained. Figure 1 is a map of the Ruhr district. Because of the magni- tude of the task of insuring an adequate supply of coal and the necessity for united action, it was deemed best to reorganize the coal-producing facilities in the British zone undor the joint supervision of American and British authorities. As a result, the UK/US Coal Control Group was established accord- ing to the organization plan indicated in figure 2. Headquarters for the group was established at Essen, in Villa Huegol, the prewar home of the Krupp family (fig. 3). One of the many problems recognized immediately by the UK/US Coal Control Group was the necessity of preventing disasters and reducing accidents to work- men in mines undor military-governmont control. Consequently, the United States Bureau of Mines was requested to furnish the services of qualified men to search for the hazards incident to coal mining and to prepare comprehensive reports on the results of their investigations. The authors, who wore selected for this task, spont about a year in Germany and visited all except a few of the smaller mince. Whereas their principal purpose was to investi- gate safety conditions, somo of the operating conditions and practices also wore studied. The results of the studies and investigations are embodied in this circular with the hope that some useful information will be disseminated to the mining industry of the United States, including supervisory officials, safety directors, engineers, and mine workmon.

Feb 1, 1950