Search Documents

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By F. K. OVITZ

In its endeavor to promote a more efficient use of coal the Bureau of Mines, in cooperation with the Illinois State geological survey and the University of Illinois, has undertaken an investigation of the coking of Illinois coals. The investigation was started by collecting from various sources the data regarding experiments already made by others; these data have been compiled and are presented herein. The present methods of using coal seem wasteful. When coal is burned in furnaces for the generation of steam, only the heat gener- ated by the fuel is utilized; possible by-products are not only lost but frequently are the source of the smoke nuisance. The volatile matter containing the tar and heavy hydrocarbon gases is difficult to burn completely in many furnaces, and its decomposition produces black smoke. When coal is coked in a by-product oven, the volatile matter is no longer a nuisance but, on the contrary, is the source of many by-products, including benzol, toluol, gas, tar, ammonia, and cyano- gen, all of which increase the value that may be obtained from coal. The coke that remains after the volatile matter has been driven off is a valuable fuel that can be used for almost all purposes for which bituminous coal can be used, and it is necessary for some metallurgical work. It has about the same heating value as anthracite coal. Because of its cleanness and its burning without smoke, it is well suited for domestic heating and the generation of steam in plants where smokelessness is demanded. The use of coke for these pur- poses would do much to eliminate smoke in cities. The best grades are regarded as essential in many metallurgical processes for reduc- ing ores to their metals. By-product coking in the United States during the past three years has increased greatly. When the ovens now in course of construction are completed, the total capacity of by-product ovens will be more than double what it was in 1913. This increase has led to a search for coals other than those now known to be available for use in by- product ovens. Tests with coals from the southern part of Illinois have indicated that coke from Illinois coal unmixed with other coals can be used for fuel purposes and that coke from mixtures of Illinois coal with low-volatile coking coal might be suitable for some metal- lurgical work. In the tests the yield of ammonia was larger than is obtained from Eastern coal. Evidently the development of methods by which good coke can be made from Illinois coals and the by-products recovered is a matter of high importance. Any investigation that will indicate how, by proper treatment, these coals can be made available to supply the market for coke and gas in the Middle West will increase efficiency in their use, and will aid in conserving the country's supply of high-grade coking coal.

Jan 1, 1917

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By H. L. Talbot, A. J. Hall, R. S. Young

A method for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators as responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control pur- poses. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or siinilar elements has come to the authors'notice. Experimental Procedure There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; Al2o3, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents as used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1949

By Corliss R. Kinney

SINCE the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated pace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. POSSIBILITIES OF ACETYLENE One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and' these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1946

By W. A. Boyer

If the safety factor of a mine hoisting rope is checked for the lowest depth, is the rope then safe for all levels? The answer here is no. A new set of volues is proposed. HOISTS for metal mines are seldom designed for one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper. The safety factor of a hoisting rope as defined by the U. S. Bureau of Mines' is the ratio of the static load to the tensile strength of the rope. It is calculated by dividing the breaking strength of the rope* In Fig. 1 curves A and B are plotted against the vertical suspended distance, which is the abscissa, and the factor of safety, the ordinates. Curve C is a smooth curve drawn through the midpoints of the steps of curve A and would more closely represent the minimum factor of safety for new rope for any particular depth. Curve D is a smooth curve drawn through the midpoints of the steps of Curve B and would more closely represent the minimum factor of safety when ropes should be discarded for any particular depth. If a new rope were applied with a minimum factor of safety, then the vertical distance or ordinate under curve D for any particular depth, divided by the vertical distance or ordinate under curve C, would represent the minimum percent of remaining area intact that could be allowed before the rope would be discarded. Also, that section of the ordinate between curve C and curve D is proportional to the section of the area of the new rope that could be allowed for wear and broken wires. Considering that point at 2500 ft on the chart, the ratio do to co would be the minimum percent of rope area remaining at the point of discard. The ratio of that portion of the ordinate cd to co would represent maximum percent of area of a new rope available for wear and broken wires.

Jan 1, 1955

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By A. G. Weber, K. H. Coats, M. H. Terhune, R. L. Nielsen

Two computer-oriented techniques for simulating the three-dimensional flow behavior of two fluid phases in petroleum reservoirs were developed. Under the first technique the flow equations are solved to model three-dimensional flow in a reservoir. The second technique was developed for modeling flow in three-dimensional media that have sufficiently high permeability in the vertical direction so that vertical flow is not seriously restricted. Since this latter technique is a modified two-dimensional meal analysis, suitably structured three-dimensional reservoirs can be simulated at considerably lower computational expenses than is required using the three-dimensional analysis. A quantitative criterion is provided for determining when vertical communication is good enough to permit use of the modified two-dimensional areal analysis. The equations solved by both techniques treat both fluids as compressible, and, for gas-oil applications, provide for the evolution of dissolved gas. Accounted for are the effects of relative permeability, capillary pressure and gravity in addition to reservoir geomety and rock heterogeneity. Calculations are compared with laboratory waterflood data to indicate the validity of the analyses. Other results were calculated with both techniques which show the equivalence of the two solutions for reservoirs satisfying the vertical communication criterion. INTRODUCTION Obtaining the maximum profits from oil and gas reservoirs during all stages of depletion is the fundamental charge to the reservoir engineering profession. In recent years much quantitative assistance in evaluating field development programs has been provided by computerized techniques for predicting reservoir flow behavior. Because of the spatially distributed and dynamic nature of producing operations, automatic optimization procedures, such as those now in use for planning refining operations, are not now available for planning reservoir development. However, present mathematical simulation techniques do furnish powerful means for making case studies to help in planning primary recovery operations and in selecting and timing supplemental recovery operations. A number of methods have been reported which simulate the flow of one, two or three fluid phases within porous media of one or two effective spatial dimensions>-4 However, applying computer analyses to actual reservoirs have been limited mostly to two-dimensional areal or cross-sectional flow studies for two immiscible reservoir fluids. To obtain a three-dimensional picture of reservoir performance using such two-dimensional techniques, it has been necessary to interpret the calculations by combining somehow the results from essentially independent areal and cross-sectional studies. To the authors' knowledge, the only other three-dimensional computational procedure, in addition to those presented here, was developed by Peaceman and Rachford8 to simulate the behavior of a laboratory waterflood. Two computational techniques which may be used to simulate three-dimensional flow of two fluid phases are described in this paper. The first method, called the "three-dimensional analysis", employs a fully three-dimensional mathematical model that treats simultaneously both the areal and cross-sectional aspects of reservoir flow. The second method, called the vertical equilibrium (VE) analysis", is applicable

By R. S. Pratt

IT is proposed to discuss the materials and furnaces, as well as the melting procedures used in preparing metal for casting billets, bars or cakes for mill fabrication. As far as possible, consideration will be given to the alloys that are commonly made in most brass mills producing strip, tube, rod and wire. RAW MATERIAL The basic raw material for such mills, of course, is copper, which may be obtained in the form of ingots, ingot bars or cathodes. Refinery-cast ingots and ingot bars, which are simply double ingots, are supplied in accordance with A.S.T.M. Specifications as regular electrolytic or fire-refined tough-pitch copper. In the wrought-metal industry, the electrolytic brands have been preferred, although during the war large quantities of fire-refined coppers sufficiently pure to be suitable for all existing requirements were imported from South America. With the exception of Lake copper, most primary fire refined coppers produced in this country have not been considered satisfactory for wrought metal alloys. Cathode copper, which is now widely used instead of ingot copper for alloying, is the electrolytically deposited metal that is normally remelted in the production of electrolytic tough-pitch ingots. It is in the form of rough, flat plates not suitable for processing but quite satisfactory for melting when sheared into suitable sizes. Raw zinc is perhaps the next most important raw material and this is obtained in various grades, depending on the analytical requirements of the alloy to be made. The grades of zinc as outlined in the A.S.T.M. Specifications vary in cost with the amount of impurities-lead, iron, cadmium-and are purchased in such a way as to produce the most economical mixture consistent with the purity required in the alloy. Other virgin metals (lead, tin, aluminum and nickel) are used in varying quantities for making copper alloys. These elements can also be purchased in accordance with the appropriate A.S.T.M. Specifications where available. Also available are a number of special alloys, which are used as deoxidizers or as means of adding relatively small quantities of elements not suitable for adding directly as virgin metal. In this category are such materials as phosphor copper or phosphor tin, silicon copper, manganese copper, cadmium copper, and copper-iron or zinc-iron alloys. Some of these alloys may be purchased on a definite alloy basis or may be produced in the plant itself for its own use. For largely economic reasons, however, a great proportion of the charge to the melting furnaces consists of alloy scrap. In the production of many finished products, as much as 70 or 75 per cent of the metal originally cast may be discarded at various points along the production line. This material eventually finds its way back to the casting shop as mill scrap, overhaul or scalping chips, skeleton scrap, rod turnings, or miscellaneous fabricating scrap. One of the most serious problems in the

Jan 1, 1946

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,' Si,' Ni,2-5 CO,'-', Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry's law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.'2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

A study was undertaken to investigate the relationship between the quantity and value of economic demonstrated resources discovered for 12 mineral commodities over a ten year period and the expenditure required to yield such mineable resources. The results showed that for every dollar spent on exploration, there is an apparent in-ground average value of around $54 dollars contained in the economic resources found. While this appears to be a satisfactory return, it should be remembered that more than 99.9% of exploration programs are judged to be failures because a viable ore body or mineral deposit was not proved up. What is behind this seeming paradox?   The fundamental truth behind mineral exploration is the fact that the more you explore, the more you find, and that one success will often lead to further discoveries. It appears that one rich and viable deposit creates such surplus that its inherent high value ('the pot of gold') makes up for all the failures. In short, mineral exploration is a high risk business with uncertain returns. However, with skill, enthusiasm, experience and venture capital, it can yield larger than normal returns for the brave and the fortunate.   Analysis of exploration expenditure and economic resources discovered for the period 1987 to 1996 revealed that the apparent in-ground value of economic ore discovered per dollar of exploration expenditure varied from a high of $429 for iron ore and $261 for bauxite to a low of $22 for gold and for lead, and $5 per dollar of diamond exploration expenditure. Preliminary conclusions drawn on the reasons for the variations observed include the inherent ease or difficulty of discovery for different mineral commodities which may in some cases, relate to the natural prospectivity of Australia as a whole. Layered deposits like iron ore and bauxite appear to yield higher in-ground value returns on the exploration dollar. To some explorationists, this may be considered as seemingly obvious, but it may have more to do with very large-exploration tenement grants pursued by various Australian State Governments in the early 1950s and 1960s than the apparent ease of delineating a stratabound deposit.   Despite the apparent relatively low in-ground value produced by the gold exploration dollar of $22, the 5660 tonnes of gold discovered in this ten year period was worth $9.1 billion and representing over a quarter of the new mineral wealth created in the ten years to 1996. This contribution, along with that from the other minerals discovered over the period, led to a significant boost to Australia's export income and standard of living.   It is concluded that, given the nexus between the amount of mineral exploration expenditure and the quantity of new resources likely to be discovered, this knowledge may help policy makers seek to influence the rate of resource discovery in countries like Australia for the benefit of the nation.

Jan 1, 2004

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By G. W. Toth

The coal mining cost models described in this paper represent a computerized estimating procedure for analyzing mining costs and requirements of proposed coal mining projects. Both surface and underground mining analyses can be conducted through the use of these models. These models were developed by the NUS Corporation for the Electric Power Research Institute (EPRI). The methodology design of the cost models follows a process engineering approach for determining mining requirements and costs similar to the logic typically employed in preliminary mine feasibility studies. All capital and operating costs associated with a new coal mining project are thereby estimated. The results of these analyses are then entered into a financial analysis framework which computes annual cash flow summaries, utilizing a profit and loss statement approach, to solve for either the coal value/ton (minimum required selling price) or the rate of return on equity for the project. The coal value/ton is also referred to as the economic cost of production (F .O . B. mine, including preparation).

Jan 1, 1980

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By Thomas A. Phillips

An economic evaluation of the Bureau of Mines process for the separation of raw urban refuse into its metal, mineral, and energy components is presented. The process recovers ferrous metal, mixed nonferrous metals, aluminum, mixed-color glass cullet, and refuse-derived fuel products from raw refuse. Data for this evaluation were obtained from selected runs at the Bureau's pilot plant in Edmonston, Md. A cost estimate was prepared for a plant capable of processing 1,000 tons per day of raw urban refuse operating two shifts, 6 days per week. The fixed capital cost, based on second quarter 1976 equipment costs, is approximately $14.5 million excluding land and shipping containers. The estimated operating cost is approximately $8 per ton of refuse processed. This does not include credit for the products, transportation of the products, a tipping fee, or a dumping fee for wastes produced. No finance charges or taxes are included in the operating costs.

Jan 1, 1977