Search Documents

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

Beneficiation of Nickel Lateritic Ore from Montes Claros de Goißs, Brazil Beneficiation is a key factor for both technical and economical aspects of industrial processing of nickel lateritic ores. A combination of comminution, classification and concentration stages are usually used to upgrade the metallurgical plant feed, thus resulting in both capital and operating cost reductions. This paper describes the testwork conducted on Montes Claros nickel lateritic ore in order to investigate the potential for upgrading. A comprehensive laboratory testing program included crushing, scrubbing, screening, grinding, gravity separation and attritioning, for both saprolitic and limonitic ore types from the Montes Claros deposit. The results indicated a clear potential for such an upgrade, which was later validated in a pilot plant program.

Sep 13, 2010

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By D. J. Pyra, J. Kudelko, Korzekwam W.

Polkowice region (Lower Silesia, Poland) is an area, where the copper mining activity started about 40 years ago and new technologies were applied. There are 3 underground mines, 3 processing plants, tailings pond (the biggest one in Europe), pipelines for flotation waste transport, railways. Although new technologies were applied during the copper ore exploitation, the environment in this area were polluted mostly by dust containing copper, lead, zinc and arsenic. Estimated values of heavy metals in polluted soils were compared to the natural contents of this metals. The geochemical background for Polkowice area was defined. The pollution zones occur around mining facilities. Copper ore exploitation and processing is planned for the next 20-40 years depending on market situation. After mines and other facilities closing the most important problem will be sustainable development of this area. To evaluate the scope of revitalization activities the analysis of recent soil environment condition will be necessary as well as forecasts for pollution migration. Geostatistic methods used also in mining will be very helpful for this task.

Jan 1, 2005

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By T. G. Lovering

Nonparametric statistical tests have practical application to many geological problems because, unlike the standard statistical tests, they do not require assumptions regarding the form of the population frequency distribution. Many of them do not even require that the variable be susceptible to numerical measurement. These tests are useful either 1) for geological data representing population distributions of unknown form, or otherwise not meeting the requirements for standard parametric tests; or 2) for sample attributes that cannot be measured but only ranked in order of relative magnitude. The application of two such tests will be illustrated. The Kolmogorov-Smimov test will be used to test for significant differences in copper distribution in samples of two rock types; the Spearman rank-correlation method will be used to determine whether there is a significant association between intensity of rock alteration and copper content of the rock. Nonparametric tests are, in general, quicker and easier to perform than the corresponding parametric tests, and they may be applied to a greater variety of data. They are not as powerful as the standard tests if used on data to which the latter are applicable, and computer programs utilizing them are not generally available. The use of standard or parametric statistical procedures for the interpretation of measured geological data is familiar to most mining engineers and explora- tion geologists. The computation of product moment correlation coefficients on sample assays for more-than one component is already standard procedure in some company operations, as is the use of Student&apos;s F test and Snedecor&apos;s F test for the comparison of means and variances of sample groups. The application of these three tests is limited by the prerequisites that the samples must be random, independent representatives of normally distributed populations and that the variables involved must be measurable. If such tests are applied to data which fall short of fulfilling these prerequisites, then the probability level attributed to the computed statistic is invalid and the conclusions based thereon may be erroneous. A number of nonparametric, or distribution free, statistical tests have been developed for use with data which are not amenable to standard parametric procedures. These tests have been widely used in the behavioral sciences such as psychology and sociology for some time, but their application to geologic problems is relatively new. Nonparametric tests may be grouped into two main categories: those which test for significant differences in a single variable by comparing either sample values with a standard value or representative values between two or more groups of samples; and those which test for significant association between pairs of variables in a single group of samples. The versatile chi square test, the Kolmogorov-Smirnov one and two sample tests, the Wilcox matched pairs signed ranks test, the median test, the Mann-Whitney U test and the Cochran Q test are examples of nonparametric tests with demonstrated or potential geological applications that belong in the first category. The contingency coefficient, Spearman rank correlation coefficient, Kendall rank correlation coefficient and the

Jan 1, 1963

By R. H. Jacoby, V. J. Berry, R. C. Koeller

The experimental phase behavior of several field gas-condensate systems, one field volatile oil system, and a series of synthetic systems having gas-oil ratios from 2,000 to 20,000 scf/bbl stock tank oil was measured. The data were used to calculate the depletion performance of the field systems at their respective reservoir temperatures and of the synthetic systems at various temperatures. The results of the performance calculations were used to prepare correlations of total stock tank oil and separator gas in-place, and the amount of each recovered by primary depletion. Data needed to use the correlations are initial gas-oil ratio, initial tank oil gravity, reservoir temperature and reservoir pressure. The correlations presented should be useful for estiinating recovery from reservoirs producing volatile oils or rich gas condensates having gas-oil ratios from about 2,000 to 30,000 scf/bbl of stock tank oil. INTRODUCTION Prediction of depletion performance for gas-condensate reservoirs usually requires extensive laboratory work or lengthy phase-behavior calculations. For many small gas-condensate bearing zones the expense of such work is often not justified. Furthermore, where large holdings are involved, it is useful to have estimates of future oil and gas production in advance of the results of a laboratory analysis, even if such work is ultimately planned. For these reasons, it would be of value to have a method for rapidly estimating the depletion performance of gas-condensate reservoirs from the type of field data usually available. Few data on the reservoir depletion performance are available for the purpose of developing correlations. The increasing number of gas-condensate discoveries and the advent of high-speed computers have stimulated the development of methods for predicting performance. Such calculated performance data have been shown to be reliable and are becoming accepted as a basis for reserve estimates and for engineering studies. It therefore seems satisfactory to use results of performance predictions themselves for the purpose of developing the desired correlations. Such an approach is described in this paper. Several rich natural gas-condensate systems (gas-oil ratios of from about 3,600 to 60,000 scf/bbl) and one natural volatile oil system were studied (2,363 scf/bbl). In addition, to provide a more systematic basis for correlating purposes, a series of related, synthetic reservoir fluid mixtures was also studied (GOR&apos;s from about 2,000 to 25,000 scf/bbl). The purpose of this paper is to show how the recovery of oil and gas by primary depletion may be estimated from surface gas-oil ratio, reservoir temperature and pressure, and tank oil gravity. procedure Experiments Companion samples of gas and oil were collected from the high pressure separators in nine different fields at the time of their discovery. These samples were each recombined in accordance with the respective producing GOR to reproduce the reservoir fluids. Eight of these fluids, designated F-2 through F-9, were rich gas-condensate systems at the respective reser-

By O. D. Sherby

In 1938, Kanter&apos; revealed that the steady-state creep rate of low-carbon iron alloys could be correlated by an activation energy expression, where the activation energy for creep, Qc, was found equal to about 90.0 kcal per mole for most of the alloys investigated. He suggested that creep at high temperatures might be controlled by some sort of solid self-diffusion process since the value of Qc was about equal to the known value for self-diffusion, Qd. Correlations were not further attempted along these lines until many years later, when new evidence2-8 was presented suggesting that Qc = Qd for many metals. This equality now appears to be established for ten metals (Al, Pb, Ni, Mg, Cd, In, a Fe, y Fe, Cu, and Au). This experimental fact prompted several investigators to postulate various mechanisms of dislocation motion which would yield an activation energy for creep equal to that for self-diffusion.7-9 Possibly the most accepted theory is that based on dislocation climb7 where a dislocation is envisioned to surmount a barrier by an atom-vacancy exchange process, thereby "climbing" from one slip plane to another. Such a model would suggest that the steady-state creep rate, i, should be directly proportional to the rate of self-diffusion, D, for a given creep stress. In order to more clearly reveal the relationship between creep and diffusion, and to eventually determine the correct model, it would be desirable to obtain data showing correlations between i and D, rather than with a comparison of the temperature coefficients, Q. It has been known for some time that the self-diffusivity of iron atoms is greatly decreased when body-centered-cubic (a) iron transforms to face-centered-cubic (y) iron. This has been ascribed to the more close-packed structure of y iron. The diffusivity ratio at the transition temperature is Da/Dy =350. Correlations of creep data for a and y iron5 reveal that the creep rates under a given stress at the transition temperature differ by about the same ratio (ea/ey 2 200). It would be difficult to reconcile these results on any other basis than that the diffusivity of atoms probably controls creep of iron in some very direct way. No other published data on other allotropic metals appear currently available for further checking such a possible correlation between i and D. Thallium transforms from a hexagonal close-packed (a) structure to a body-centered-cubic (ß) structure at 230°C (503°K) and the self-diffusivities of the two structures have been determined by shirn.10 His results are plotted in Fig. 1 where it will be noted that Dß/Da = 25 at the transition temperature. It would appear desirable, therefore, to determine the creep rates of polycrystalline a and ß thallium at the transition temperature, as well as determine

Jan 1, 1959

By Y. P. Chugh

The use of wooden supports, supplementary to the primary method of roof control using roof bolts in mines, consumes over 3 million cubic meters of hardwood in the U.S. annually. These supports arc primarily used in the form of cribs and posts. Along with a rapid depletion of high quality timber resources, supplies fluctuate seasonally, costs are escalating rapidly, and product quality is highly variable. Environmental considerations of global climate change put additional pressure on deforestation for utilization of timber for artificial supports. On the other hand, management of coal combustion byproducts (GCBs) from power plants has become a major issue to maintaining a healthy coal industry. The USA currently produces over 100 million tons of CCBs annually and the average cost for their management in the US is about $20/ton. This cost is expected to escalate rapidly with tougher environmental regulations. The principal author has been directing research, development, and demonstration studies for CCBs-based artificial supports and lightweight structural materials in mines for the past seven years and has made significant progress toward commercially viable products. More specifically, first and second generation crib elements and post elements have been developed, characterized analytically, and demonstrated in the field. It is estimated that about 2.5 x 10" tons of fly ash could be utilized for artificial supports in U.S coal mines and this would double if these materials were utilized in non-coal mines as well. The author believes that CCBs-based artificial supports have the potential to replace wooden supports and blocks with better performance and cost competitiveness while managing CCBs in an environmentally sound manner. This paper focuses on the development and field demonstration of CCBs-based artificial supports for use in underground mines, and its pilot scale fabrication facility. Recent analysis results on engineering performance evaluation of the developed crib under various loading conditions using finite element method are presented. The following comments highlight the developments: I ). Engineered artificial supports, crib and post elements, using CCBs as a major constituent, have significant potential for application in mines because their structural performance is significantly better than wooden cribs counterparts. 21. Engineered crib elements provide about 50% larger area for air-flow than a conventional wooden crib. 3). Engineered crib elements are not flammable. 4). Each engineered crib element utilizes about 10 kg of fly ash, about 40 % of the weight of crib element- Therefore, a typical crib 2.0 m high utilizes about 200 kg of fly ash. 5). Each 16.5 cm diameter engineered post utilizes 50 kg of fly ash. 6). Assuming 3.0 million cu. meter of wood consumed for post and crib support systems, it is estimated that about 4 - 5 million tons of fly ash may be utilized for supports fabrication in the USA. 7). An engineered post has excellent post-failure characteristics similar to wood. In addition, the engineered post also has excellent loading and unloading characteristics close to the yield point of about 75% of the ultimate load carrying capacity.

Jan 1, 2004

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies&apos; requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite&apos;s unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

Ground conditions at the Kencana mine, Indonesia, are generally poor and an underhand cut and fill mining method is used for extraction. Due to these poor ground conditions, all vertical development has been conducted using blind, top-down, sink and line excavation methods. Due to time constraints, raiseboring was considered the only viable excavation method for the installation of a return ventilation system for the K2 (Kencana extension) project. In order to achieve successful raiseboring in the poor ground conditions a number of strategies were used including: a detailed geotechnical study for optimal position of the shaft/s, splitting shaft excavation vertically, raiseboring of multiple smaller diameter shafts, extensive pregrouting, installation of drainage holes, and rapid installation of support following excavation.

Nov 25, 2010

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Qing Wang

In this method the state of an open-pit mine is represented by the number of benches that are mined in each predesigned mining phase (or pushback). Consequently, a specific mining schedule can be represented by a sequence of states which starts with the topography of the mine site and ends with the ultimate pit. For a given set of mining phases all feasible states are first generated and sequences of states are then evaluated for technical and economical feasibility. The best sequence, which gives the maximum net present value (NPV), is found by applying a dynamic programming optimisation algorithm. The algorithm also optimises the cut-off grade which satisfies the mill feed requirement for each planning period. It was found that the algorithm can be used not only for scheduling but also as an effective tool for analysing the effects of mining and milling capacities and cut-off constraints on the mining schedule and the total NPV. The algorithm, which was programmed in C, was successfully applied to a large Au-Cu deposit

Jul 1, 1996