Search Documents

By AUIMM AUIMM

Continuous Improvement The Council of the AusIMM should expedite the introduction of a continuous professional education policy along the lines of that to be proposed to you by David Pollard today. The Education and Accreditation Committee must continually review the training needs of the next generations of mining industry professionals. It should continue to demand and encourage the creation of the schools for the training of such people. The AusIMM could even put greater onus upon university researchers to accredit university post graduate degrees.

Jan 1, 1994

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By J. B. Vander Sande, L. C. Rainey, P. Bolsaitis, B. Dirsa

"The structure and composition of silica-rich particles recovered by lavage from the lungs of three active miners with different medical histories were studied using high-resolution electron microscopy and chemical microanalysis. The results arc compared to the similarly determined structure and composition of respirable-size mineral particles obtained from roof-bolter dust-box samples from two coal mines of widely different bulk quartz concentrations. The results show that the lungs of the miners contain silica-based particles with structures not found in the mine samples. Also, the particle structures and compositions found in the macrophages were different in each of the miners. The rau.lu suggest the possibility that intracellular processes may affect the susceptibility of individuals to silica-induced pneumoconiosis. The cytotoxic and fibrogenic potentials of mine dusts result from the activity of their individual components. Whether this effect is additive or even mass (i.e., dose) related is questionable and has been the subject of many investigations. Particle size and size distribution of various constituent minerals, the surface structure and properties of individual particles, and the self-cleaning capability of the lung (i.e., the capacity of the macrophage system) may, among other variables, affect the pathogenic changes induced by dusts lodged inside lungs. Extensive epidemiological investigations conducted on miners from different coalmining districts, where equivalent dust exposures have been shown to result in vastly different frequencies of lung disease incidence, also confirm this hypothesis (1) In a recent study, Ferrer et al. (2) used energy-dispersive X-ray analysis (EDXA) to investigate the inorganic element content in pleura and lung in reference, silica exposed non-pneumoconiosis, and silicotic populations. Constant depositions of silicon and calcium were detected in visceral pleura, parietal pleura, and lung of the refence group and in visceral pleura and lung of the exposed non-pneumoconiosis and silicotic groups. Comparison of the silicon content in pleura between silicotic and exposed non-pneumoconiosis subjects showed a nonsignificant probability of difference, whereas there were no differences with respect to the silicon content in lungs."

Dec 1, 1995

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By Ann C. Kim

This Bureau of Mines report summarizes the methods and results of many of the laboratory studies on spontaneous heating of coal published in the last 50 years. It includes a brief description of experimental methods, indices of combustibility, and important contributing factors. Adiabatic calorimetry, isothermal calorimetry, [0], sorption systems, or temperature differential are the most frequently used experimental methods. Indices of combustibility include various heating rates, crossing point temperature, ignition temperature, and CO index. Factors that affect the spontaneous heating of coal include air flow rate, changes in moisture content, particle size, rank, temperature, pyrite content, geological factors, and mining practice. Experimental conditions and results from 20 papers are summarized in an appendix, and the bibliography contains 45 references.

Jan 1, 1977

By David Heyl

"El presente texto señala la evolución de los modelos genéticos de geología económica del yacimiento minero Tres Cruces. Dicho yacimiento se encuentra localizado en el noreste del Perú, adyacente al distrito minero de Quiruvilca. A partir del año 1995 se le reconoció como el mayor productor de oro a través de un programa de exploración en la Formación volcánica Calipuy. Posteriormente, el yacimiento fue visitado por variosgeólogos que postularon diferentes modelos genéticos del yacimiento para así estimar su potencial económico -en tanto se incrementaron los datos geológicos del yacimiento. Por ello, el texto presenta el modelo genético de Tres Cruces, como el más adecuado, aunque la evaluación de su potencial econornica está aún en progreso."

Apr 26, 1999

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924

By A. Ignatieff

"A practical picture of the effects of stress and of the structural environment in an extraction area in a bedded deposit is described, and the main factors of ground control where principles of rock mechanics can be applied are discussed. Reference is made to early work in Europe, where systematic rock mechanics studies started in coal mines, as well as to the early work in the Canadian coal mines.During the past two decades, considerable theoretical and experimental knowledge, pursued both in the laboratory and in the field, has accumulated throughout the world, but the state of the science still does not permit application of substantiated theory such as is found in the design of above-ground structures, largely because of the complexity of the rocks. The mining engineer, as oppm1ed to the civil engineer, is constantly faced by exposures of new ground that is often subject to unpredictable discontinuities. However, the rationale already developed by rock mechanics principles and experimentation provides concepts and information that may be useful in selecting mining layouts. These concepts and existing measuring techniques can also assist ground control as mining progresses.Many of the bedded deposits, much as coals and evaporites, have pronounced deformation properties, and there are limitations in making stress measurements within short distances of mine openings or extraction areas. On the other hand, the measurement of movement of the hanging wall (roof) and footwall (floor) of roadways and extraction faces, as well as the sides of pillars, provides a most useful tool in assessing ground stability.This paper is to be regarded as a brief progress report with particular reference to Canadian applications of rock mechanics to bedded deposits."

Jan 1, 1968

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By G. B. Glass

In 1996, 92.5% or 233 Mt (257.4 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River Coal Field. While the mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft), the thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash, and 19.98 MJ/kg (8,590 Btu/lb). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coal beds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 10.2 billion cu ft a year. This production is occurring just west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By J. Richard Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a. few years ago still exist today and will continue to be present in the future. Improvement's in production mining equipment, mining methods, and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been improved previously, and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effect on production is not pronounced and cannot be readily resolved. The need for a method of analyzing such factors was recognized by the Office of Coal Research. Therefore, in April 1962, under OCR sponsorship, a. research project was initiated at Virginia Polytechnic Institute (VPI). The objective of the project was to identify the factors which influence mining costs in the immediate production area, and to develop methods and techniques which will enable the coal operator to minimize production costs. The objective of the research at VPI has been successful, and techniques have been developed for establishing quantitative facts concerning the interrelationships of production activities.

Jan 1, 1965

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Yury Kapelyushin

Formation of cementite in the reduction of hematite by CO–CO2 gas was studied in situ using high temperature XRD (HT XRD) analysis. Reduction of hematite was examined in the temperature range 873–1173 K by CO–CO2 gas mixture with high carbon activity. When carbon activity in the system was 1.5, cementite was formed only at 1023 K; it was not observed in experiments at 973, 1073 and 1123 K. Formation of cementite was observed at 923–1073 K when carbon activity increased to 3–5; and at 873 K when carbon activity was 10. Formation of cementite at 973–1073 K proceeded through metallic iron; however, in the reduction of hematite at 873 and 923 K, iron was not observed; cementite apparently was formed directly from wüstite. XRD spectra were used to estimate concentration of carbon in austenite in the process of cementite fromation.

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971