Search Documents

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

For a large scale open pit mining and concentrating operation, on a low-grade disseminated ore body, it is possible to set an approximate lower bound on economically feasible operating scales and an approximate upper bound on economically desirable scales in a relatively straight forward manner. The optimum scale ofplanned operations, with respect to the objective ofmaximisation ofthe net value ofthe orebody, will have to be arrived at by iterative planning runs, but it may be expected to lie close to this upper bound. The effects of infrastructural costs and of the addition of a risk premium to the cost of capital, to form the discount rate for planning purposes, are considered theoretically and by worked example. It is concluded that a perceived special, unsystematic, risk should not be accounted for by the use of such a risk premium as this is inducive to placing a greater amount of investment capital at risk, for no greater return-rate to investment.

Jan 1, 1986

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By Tetsuo Yamazaki

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has currently been recognized. The thin layer-type deposit characteristics affect not only the excavation efficiency but also the economy of mining venture. Considering the thin layer-type distribution and the utilization of some rare metals in cobalt-rich manganese crusts, a preliminary economic feasibility of the mining venture is evaluated. Under some preliminary technical assumptions, the possibility of cobalt-rich manganese crusts for future rare metal sources for Japan is examined. The important role of utilization of rare metals in the crusts is highlighted.

Jan 1, 2010

By Benedict Shubart

The subject of this paper may seem threadbare to, many of you, but even if I repeat what you already know, just smile to yourself and think how much wiser you are than your neighbor, for it is startling what a number of tipples are erected that violate the elementary fundamentals not only of good design but of practical operation. Possibly a coal screening plant is a simple plant. If so, we treat it like we do a great many other simple things. We treat it entirely too lightly and fail to take into consideration, not only the changes that may occur later, the conditions we may be compelled to meet as competition changes, but even the elementary physical conditions that exist right at the tipple site. If I get too positive over some particular point, don't blame me, but remember some of the heart-breaking experiences we have had correcting these omissions, trying to make a tipple do merely what it was designed to do, when the builder tied everything up in such a constricted space, that no room was left to get the results he must have. Perhaps some of the things will look too expensive. Don't say that you can't afford them. Many of them you can't afford to do without, and when you figure that a tipple is put up for possibly twenty years of operation, you can't afford to omit any reasonable precaution not only in taking care of the present, but in foreseeing the future. We will consider a tripple screening plant, suitable for Western conditions, capable of handling approximately 2,500 tons per eight hours. The largest screen sizes must be loaded into either open cars or box cars, and arrangement provided for screening and loading not less than five sizes of coal: lump, egg, nut, slack, dust, or any reasonable combination of these. As we are considering only the preparation of the coal, we will omit all consideration of the method of haulage, pit cars, methods of dumping, and will take the coal after it is in the dump hopper. The track arrangement will frequently be determined by the ground layout. Our sizes and tonnage can be loaded on three tracks, but four tracks are better. The two outer tracks should be left for loading lump coal, No. 3 track should be left for egg coal, and No. 4 track for loading nut, slack and dust. Where a fifth track can be provided, No. 5 track should be held open only for run-of-mine coal, to act as a storage where emergency coal can, be run, should there be any delay in the screening equipment or in changing cars. Track No. I should be used for loading lump coal into box cars only. Track No. 2 should be used for loading lump coal into open cars only, and may or may not be provided with picking table, loading boom, or both. Where picking is necessary, a picking table can frequently be put between the two "lump tracks, heading down track, pivoted at one end, so it may be raised or lowered to feed either open or box cars; with

Jan 1, 1921

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946

Taking the Long View THE present international situation has serious implications for this nation. The possibility of total war is no more appalling than the threat of making the United States permanently into an armed camp. A period of ten years under such conditions could mean a Communist victory without firing a shot-if the present trend toward statism is allowed to continue. As individual citizens and as members of the mining profession we have the power to oppose the march toward socialism. We must not adopt shortsighted policies dictated by self-interest, but must endeavor to size up the situation as a whole and act according to what will be best in the national interest. The economic picture for the metal mining industry under present emergency conditions is apparently bright. Demand for metals exceeds supply. But there is danger that fluctuating prices will bring Government regulation. Care must be exercised in our pricing policies, or the calamity of Government intervention will be inevitable. President Truman's "loophole" reference to percentage depletion early in the year caused a brief flurry of excitement, but now that the immediate threat is over the industry has lapsed into sommolence on this subject. Special tax privileges accorded the mining industry because of inherent risks should be guarded by a continuing propaganda campaign to educate Congress and the public. If this is not done we may find ourselves losing the necessary tax protection which we now possess by a capricious act of legislation. Stockpiling minerals from abroad certainly lengthens the life of our own mineral resources. The present consumer demand for the base metals indicates foreign sources of supply for stockpiling. However, this is only one facet of the problem. For strategic military reasons it is necessary that the United States have quick sources of all minerals within our national boundaries. Undeveloped mineral deposits do not meet this need so that where it is possible to encourage our own mineral development by stockpile purchases, it should be done. A need exists for an overall controlling agency that would make purchases for the stockpile according to military necessity, current metal market conditions, and so as to strengthen the mining industry. In the course of the history of the United States we have been engulfed in several wars by the necessity of protecting our economic rights abroad trading privileges-and also because of moral obligations. Disregarding the moral side, it is difficult to reconcile fighting wars to protect world freedom of trade when in peacetime we attempt to restrain such trade by tariff barriers. When it comes to accepting subsidies from the Government in one form or another it is difficult to overlook the immediate personal gains and see in the future that where the Government lays out capital it becomes a partner in the business and not a silent one. It is apparent that hope for the traditional American way of life cannot be bought without some self-sacrifice; and we cannot wait for the other fellow to start it because it is the responsibility of each individual citizen. By taking the long view our course should be apparent and not diverge sharply from our own personal benefit.

Jan 10, 1950

• As part of $850,000 granted by the House Appropriations Committee for development of manganese in the U.S., the Bureau of Mines will build a pilot plant at Artillery Peak, Ariz., for development of low grade manganese ores. • The historic Argo tunnel and mill in Idaho Springs, Colo., will reopen shortly for the mining of uranium. The Uranium Co. of America has acquired control of the tunnel and mill and 12 nearby mining properties. J. H. Rodgers and G. C. Ridland will manage the operation. •The opening of a new 4000-ton per day coal mine in Washington Co., Pa., and the reopening of another mine of the same capacity in Fayette Co. has been announced by the H. C. Frick Coke Co. They'll help meet added war demands. •A 7000 bbl per day commercial synthetic liquid fuel plant, making gasoline from natural gas at Brownsville, Texas is being operated by the Carthage Hydro-col Corp., a Texaco subsidiary. The gasoline is produced by the Hydrocol process, chemically similar to the Fischer Tropsch process, but differing mechanically in several ways. To operate the process it has been necessary to build an oxygen plant producing 95 pct pure oxygen in quantities equal to U. S. production of commercial oxygen in 1946. •Over 96 pct of the class of 1950 at Montana School of Mines are now employed,, in industry, and they're scattered from MIT to the island of Cuba., • Cobalt, heretofore almost entirely imported, will soon be produced in Idaho. The Calera Mining Co. is building a 600-ton mill in which a cobalt and copper concentrate will be obtained from Idaho ores. •Plans for mining iron ore on the Conarky Peninsula in French Guinea, (an ECA project) call for equipment purchases as follows: 8 wagon drills, electric shovel for mining, conveyor for the port, 8 trucks, wrecker, 2 tractors, as well as miscellaneous accessories and spare parts. •A low-grade lead-zinc mineralization, located east of any known ore bodies in Utah's East Tintic district, has been located by a 2000-ft wildcat USGS drill hole. * Higher-than-going rates have been authorized by the Munitions Board for its stockpile program, where domestic production of scarce materials is low or uneconomical. Payment in excess of 25 pct over the foreign price is now permitted. •A new self-centering conveyor roll, developed by Carnegie-Illinois Steel, is expected to revolutionize materials handling. It completely eliminates the necessity for sideguides to keep materials on a conveyor. See P. 1028. •Great Britain's socialized coal industry employs twice as many miners, but produces less than half as much coal as America's coal industry. last year, British mines produced 28 million fewer tons of coal than the output of the same ,mines in 1939. Absenteeism amounted to a big 12 pot of working time. • Labor market conditions have tightened on almost a country-wide scale. Only 4 out of 143 major labor market areas have a substantial surplus -- less than half the total for May. Growing scarcities of skilled labor are in evidence.

Jan 10, 1950

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

BEING at the crossroads, metaphorically speaking, seldom has the advantages of the literal sense of the words. One seldom has precise knowledge of the existence of the metaphorical crossroads or forks in the road of life. A case in point is the Committee on Education of the Engineers' Council for Professional Development, which for twenty years has been accrediting the engineering curricula in the educational institutions of the United States. The committee is now at odds with itself and with the National Council of State Boards of Engineering Examiners over the accrediting of courses which in the opinion of many engineers are not strictly speaking engineering curricula at all. Such courses include: fire protection engineering, crystal engineering, nuclear engineering, and geological engineering. The crossroads might be placed arbitrarily somewhere between 1936 and 1938 when the committee first started accrediting curricula and included the first course in industrial engineering. Purists might argue that the committee first wandered from the straight and narrow when it recognized subdivision of engineering into the major branches of mining, metallurgical, civil, mechanical, electrical, and chemical engineering. Accrediting is certainly an important function because it provides a standard for engineering education and it should be done on a national basis by an unbiased group like the Education Committee of ECPD. Students, educational institutions, and industry derive great benefit from proper standards. The autonomous State Boards of Engineering Examiners have long accepted ECPD accreditation as evidence of the required academic training of engineers aspiring to licensing. But the State Boards today question the wisdom of applying the name engineer to graduates of some of the so-called fringe curricula. The Education Committee, having gone so far in accrediting some of them, has numerous applications pending for accreditation of similar curricula and even new courses never before accredited. Arguments against recognizing highly specialized engineering curricula are numerous. The Salary Stabilization Board has disallowed industrial engineering from classification as engineering for its purposes. A graduate of a specialized course in geological engineering at a school in the Southwest slanted heavily for practice in the petroleum industry might not be interchangeable with a graduate of a similarly designated curricula at one of the institutions in the North Central states where the emphasis might be on metallic. mineral deposits. Industry in general should not expect the universities to supply a degree in each of the specialized engineering classifications it might set up for purposes of salary or job designation. Having gone so far, it is easy to understand the difficulty of the Education Committee. ECPD might well call a moratorium for the purpose of taking stock of its position. If the present trend is allowed to continue, it is apparent that an engineering institution could be subdivided into a multiplicity of departments teaching specialized curricula resulting in a subordination of the basic concepts of engineering. Although the parallel of the medical profession is trite, it should be pointed out that degrees in medicine are not labelled by the numerous specialities practiced by doctors. For practical purposes the ECPD would do well to accept the fact that the crossroads have been overreached "and protect the engineering profession by coming up with minimum standards for an engineering curriculum.

Jan 1, 1952

By A. A. Burr, D. Caplan

IN carrying out experiments in metal-gas systems, it is often difficult to estimate how long a reaction period must be allowed for equilibration. This is especially true in systems for which the diffusion coefficient is not known. In an investigation of the Cr-O system, the necessary information was obtained in the way described subsequently. Two pieces of chromium sheet of different thicknesses were packed in mixed powders of chromium and Cr2O3 and sealed into an evacuated metal capsule by welding. Austenitic stainless steel proved suitable as a capsule material up to 1350°C and molybdenum at higher temperatures. The capsule then was heated at a specific temperature for a time sufficient to saturate with oxygen the thinner but not the thicker specimen. The time is readily estimated from a preliminary experiment if a sufficient thickness differential is chosen. Under these experimental conditions, the metal sheet is exposed to a partial pressure of oxygen equal to that of the dissociation pressure of the oxide and hence can become saturated with oxygen without developing any second phase. After cooling, both samples were analyzed for oxygen by the vacuum fusion technique. Assuming that the surface of the specimens is kept saturated with oxygen throughout the experiment, the diffusivity can be calculated by application of the appropriate solution to Fick's second law. This is most conveniently accomplished by use of a plot of mean fractional saturation (Cm-Co) / (Cs-Co) vs (Dt) ½/L as given by Darken,' where t is time, L the half-thickness of the sheet, and D the diffusion coefficient. Cm, the mean concentration at time t, is given by the oxygen percentage in the thicker specimen; Cs, the constant surface concentration, is the oxygen percentage in the thinner specimen; Co is the oxygen content of the original chromium sheet. (Cm-Co) / (Cs-Co) is calculated and the corresponding (Dt) ½/L is read from the graph and D thereby calculated. By performing the experiment at two temperatures and plotting log D vs 1/T, the D for any temperature is established. (The activation energy for diffusion may be obtained from the slope of the line.) Once D is known as a function of temperature, it is a simple matter to estimate the correct reaction time for experiments with single specimens at other temperatures by equating (Dt) ½/L to its value for effective saturation. Darken' points out that this is approximately unity. The solubility of oxygen in chromium, as determined from the thin samples at each temperature, proved to be approximately 0.03 pct at 1350°C and less at lower temperatures. Due to low solubility and to the known difficulties of the vacuum fusion method in this low range, the values obtained for D (5x10-0 sq cm per sec at 1350°C) are estimated to be correct only within an order of magnitude. Nevertheless, the method has proved useful in estimating reaction times. Its usefulness will be greater in metal-gas systems where the solubility is appreciable. A second function of the method is to permit the determination of diffusion coefficients in systems for which the conventional techniques are experimentally difficult or impossible.

Jan 1, 1956

By K. H. Coats

In tnany oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. This paper treats the problem of optimally locating the trunkline(s) for a given systet to nlinimize both the total length of piping connecting the individual wells or lease batteries to the trunkline and the length of the latter. Single and multiple trunklines, varying line sizes, and grouping of wells are considered. Some attention is paid to the case of a curved trunkline. A field case is treated and conclusions are that the problem of locating a single trunkline is relatively straightforward while the location of multiple trunklines requires further research. INTRODUCTION la many oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. A single field may concurrently require piping systems for gathering of oil, gathering of gas, injection of water or gas and disposal of salt water. Two problems arise in the consideration of any one of these networks. The first involves the sizing of the various segments of the network to minimize piping and compression costs. The second problem, treated herein, is that of optimally locating the trunkline(s) for a given piping system to minimize the total length of pipe connecting the individual wells or lease batteries to the trunkline. This minimization problem may arise in field automation if it involves replacement of individual lease batteries by a central field battery which will require trunklines and connecting pipelines to individual wells. The problem also arises in connecting a gas pipeline through a subsidiary trunkline to wells in a gas storage field. The first analysis given below treats the case of a single trunkline and of separate connecting lines for all field units.* The analysis is then extended to consider multiple trunklines and common connecting lines for groups of field units. Varying sizes, and therefore costs, of the connecting lines are taken into account. A simplified development is given to illustrate the manner in which line sizing calculations may be integrated with the line placement problem. This study is primarily directed toward the placement of straight trunklines, although for certain field shapes or well distributions curved trunk-lines might be preferable. Some mathematical consideration is therefore given to the placement of a curved trunk-line in a field. The determination of optimal locations for two or more trunklines involves some difficulties which are discussed below. The need for further research in this area is emphasized. The problem of a single trunkline is solved in relation to an actual oil field. The problem of optimally locating two trunklines in the same field is also treated and the results are compared to the single-trunkline case. All calculations reported were performed on an IBM 7072 digital compker. The importance of right-of-way, roads and terrain in locating trunklines and connecting lines is realized. The present analysis is advanced on the premise that in planning piping networks one should start with the optimal conditions whenever possible and proceed therefrom.

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By Diane Moody

I have been asked to give you the National Coal Association's (NCA) view of the future of the coal industry. However, before discussing the outlook for the future I would like to set the stage by taking a brief look at how the industry has changed over the last decade. In 1977 the coal industry was in the midst of a period of steady growth. Although most of the gains in the early and mid 1970's occurred in the west, the industry was still predominately eastern, with eastern production accounting for 76 percent of the 697 million total tons produced in 1977. The labor force was nearing a high - at over 220,000 workers, and the number of active mines was also at a decade high of over 6,000. Productivity on the other hand was at a low. The average miner produced 1.80 tons per hour, and labor relations were also at a low point. Projections for coal's future were very optimistic, mainly because of the unprecedented growth in coal use by the utility industry. In 1977 the 477 million tons of utility coal accounted for 68 percent of U.S. coal production, and the utility industry planned on 129,000 MW of new coal-fired capacity over the next decade. Consumption of metallurgical coal at coke plants was the second largest market at 78 million tons; the industrial and residential market consumed 70 million tons and exports were at 54 million tons. But in retrospect, a lot was happening in 1977 that signalled many changes in the coal industry: - Amendments to the Clean Air Act were passed, which required that utilities take an entirely different approach to meeting New Source Performance Standards at new plants, and required that standards be set for industrial boilers as well; - the Surface Mining and Reclamation Act became law; -electrical generation, despite the optimistic forecasts, was nearing the end of a period of close to five percent annual growth; -1977 ended and 1978 began with the longest coal strike in U.S. history. -crude oil imports in the U.S. reached an all time high as did both total consumption of petroleum products in the U.S. and oil consumption at utilities. The high level of oil imports set the stage for the oil price increases of 1979 and 1980 which resulted in an immediate increase in demand for coal, not only in the United States, but world wide. Labor strikes in Australia and Poland sent foreign buyers to the U.S. literally in droves, and quickly made the U.S. a force in the world steam coal market. The U.S. coal and transportation industries responded to this overwhelming potential demand for coal. In a very short time, the capability had been developed to mine and transport the 1.2 billion tons of coal that forecasters said would be needed by the mid 1980's. What was not anticipated was that the economic effects of sharply higher oil prices would dampen demand for energy, especially for electricity, as quickly as we have seen; that coal industries in other countries would respond as rapidly as the U.S. coal industry, and at a rate

Jan 1, 1988

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By H. T. Clark

NO previous determinations of the deformation or recrystallization textures of titanium or of titanium-base alloys have been reported in the literature. The room-temperature structure of titanium is hexagonal close-packed with a c/a ratio less than 1.633. It would be expected, therefore, to have a rolling texture similar to that of other hexagonal close-packed metals, namely (0001) [1010]. Burgers and Jacobs1 have shown that zirconium, a metal isomorphous with titanium in its structure and similar in many of its properties, has such a texture with a scatter of the basal plane toward the transverse direction. This scatter is in the opposite direction from that found in magnesium by Bakarian2 but similar to that reported by Smigelskas and Barrett3 or beryllium. The rolling and annealing textures reported here for high-purity iodide titanium are significantly different from the . textures of any other hexagonal close-packed metal. All titanium used during this investigation was prepared by the iodode process." The annealed hardness of this material varied from 73 (material used for sample No. 2) to 97 Vickers hardness number. An estimate of the chemical composition of this grade of titanium has been reported by Finlay and Snyder.5 With one exception, shown in table I, the as-deposited titanium was cast into 10 to 20 g ingots in an electric arc furnace in purified argon before being rolled to sheet. The cast ingots were forged and ground until their cross-section was approximately rectangular, annealed 1 hr at 700°C in vacuum and cold rolled. Rolling was carried out in a two-high, 4 in. diam mill, using reductions no greater than 10 pct per pass. The direction of rolling was reversed after each pass, and, in order to avoid temperature effects, the sheet was allowed to cool after each pass. Unless the rolled sheet was sufficiently thin for X-ray penetration (about 0.004 in.), it was reduced to this thickness by pickling. Because of the possibility of introducing twinning or other deformation during grinding, no attempt was made to maintain uniform thickness of the sample during pickling by intermediate grinding or sanding operations. Those samples to be used for determining the annealed texture were recrystallized by vacuum annealing the cold-rolled sheet for 1 hr at 500°C. These thin samples were held between thick titanium sheets during annealing to prevent distortion. Table I outlines the rolling and annealing schedule of those samples for which photograms or texture patterns are shown. X-ray Techniques The usual techniques for determining textures were employed during this work. Molybdenum radiation was used for the transmission exposures and copper radiation for the glancing angle ones. Since titanium fluoresces under these conditions, it is necessary to employ a filter between the sample and the film. The Kß radiation filters are very satisfactory for this purpose. Sufficient grains having favorable orientation were present in both the cold-worked and in the cold-worked—500°C annealed samples to provide satisfactory patterns with the samples stationary. Because of the difficulties of comparing intensities of transmission photograms with those obtained

Jan 1, 1951

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970