Search Documents

By Thomas J. Mason, Geno Saccomanno, Victor E. Archer, Philip C. Prorok

INTRODUCTION A population of several thousand uranium miners in the Colorado Plateau region of the United States has been under surveillance since 1957 using sputum cytology and other procedures. Attempts were made to collect sputum samples annually for those miners showing normal sputum or only minor abnormalities, and on a semi-annual schedule for miners having more severe cytological abnormalities. For individuals having carcinoma in situ or malignant cells in their sputum, samples were taken more frequently. As in any human population, however, these schedules were not always adhered to, and samples were often acquired less often than scheduled. On the basis of the thousands of sputum readings that have resulted from this surveillance, one can calculate the durations or sojourn times which individuals spend in the various cytologic states into which the sputum readings are classified. This paper presents some preliminary, descriptive results concerning relationships among the cytologic state duration distributions in this population, and their associations with other variables such as radiation exposure and cigarette smoking. There are several reasons for studying cytology results in this observational setting. Of considerable interest is the opportunity to gain insight into the preclinical natural history of lung cancer. Such information would be valuable in the future design and interpretation of screening programs for the early detection and treatment of lung cancer, should this activity prove to be of benefit in experimental trials. Secondly, it is of interest to determine if some characteristic of sputum cytology readings can be utilized to determine a decision point at which to transfer a uranium miner to another job category within the industry in order to effectively reduce his probability of developing lung cancer. For example, a reading of moderately atypical cells in the sputum has been suggested as a possible decision event which would be sufficient to warrant such a transfer. In the analysis which follows, an attempt will be made to develop information relevant to these issues. The data base for our analysis, largely developed over a period of more than 20 years by Drs. Geno Saccomanno and Victor Archer, contains sputum readings classified into one of eight cytologic states: normal, metaplasia, mild atypia, moderate atypia, marked atypia, suggestive, suggestive-equivocal, and malignant. The two suggestive states will not be considered as these categories seldom contain enough observations to generate meaningful results. The duration in a given cytologic state for a given individual is calculated as the sum of the intervals between consecutive sputum readings in that state. When two consecutive readings are in two different states, half the between-readings interval is assigned to each of the two states. Among all individuals in the data base, only those having at least two sputum readings are used so that a duration can be calculated. Furthermore, the analysis is limited to individuals whose successive readings are no more than 24 months apart, so as to focus on a population which was under surveillance on a reasonably regular basis. RESULTS The overall distributions for the cytologic states are displayed as histograms in Figures 1-3.

Jan 1, 1981

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By Howard I. Epstein, John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still overflowing clear water. Some thickeners such as the Center, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickeners. l .2 , 3 A schematic diagram of the traction type Dorr thickener is shown in [Fig 1]. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in [Fig. 2]. The particular scalloped bottom discussed in this paper employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the equivalent plate for the tank with a conical bottom. This result, along with the simpler fabrication procedures required, accounts for the cost savings associated with this design. The raking mechanism employed may be the same as for the conventional conical bottom since the settled material soon forms a conical surface. Determination of the internal force mechanism for the scalloped bottom leads to designs that utilized material efficiently and thus maximize the cost savings. The complicated geometry of these bottoms along with the difficulty in analyzing the structure are factors which may have limited the use of scalloped-bottomed tanks to date. When such tanks have been built, the uncertainties associated with the internal forces have led to designs that are somewhat inefficient. In this paper, equations relating the geometric parameters are presented along with simplified closed-form solutions for the internal forces in the cone segments, from which the loads applied to the beams and the loads carried to the cylindrical tank shell can be deduced. An example is presented to show the magnitude of the savings which may be realized with this configuration.

Jan 1, 1979

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By J. C. Williams

THE operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent-namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components-that is, the silica, alumina, iron and lime-and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1946

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By ARTHUR S. DWIGH

Discussion of the paper of W. W. NORTON, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August., 1914, pp. 1993 to 1999. ARTHUR S. DWIGHT, New York, N. Y.-Mr. Norton&apos;s chief argument is directed against the idea that the D. & L. sinter is any better material for the blast furnace than the H. & H. product. He supports this by citing two experimental furnace runs. Reducibility.-To discuss a furnace record like that quoted by Mr. Norton for the five days&apos; run in August, 1912, is manifestly difficult for an outsider, but a possible explanation for the poor reduction on Furnace No. 5, smelting D. & L. sinter, may lie in the fact that both sets of furnaces carried the same fuel charges. Other things being equal, if 11 ½ per cent. coke was right for the furnaces smelting H. & H. product, it Was too much for the furnace smelting D. & L. product, as I shall endeavor to show later, and incipient overfire, accompanied by higher leads in slag and matte, was induced. It may sound like a paradox to say that excessive fuel sometimes produces poor reduction, but it is a sad fact. In certain plants where practically the entire charge to the blast furnaces receives a preliminary treatment by being sintered on the D. & L. machines the peculiarities of this problem have had to be very carefully studied, for serious metallurgical difficulties presented themselves when the change was first made to D. & L. sinter in large quantities. Some of these plants had blast pots before they had D. & L. machines, and many opportunities were afforded for comparative study of this very point. There is reason to believe that, clue to the long period of blowing and the higher temperatures developed in the pots from greater mass action, the iron in the H. & H. product is present chiefly as Fe203, perhaps in the form of ferrites, while in the D. & L. product the iron is present as FeO. The fuel charge in the blast furnace must be so proportioned as to exactly meet the chemical and thermic requirements of reduction and melting. If ally of these functions have been performed before the material enters the furnace, a corresponding allowance should be made or the fuel balance will be disturbed and bad work will result. One of the functions of the coke is to reduce enough metallic Fe for the matte requirements, leaving the remainder of the iron as FeO to go into the slag. In smelting almost any other material than D. & L. sinter the iron must-be reduced from the higher oxides, Fe203 or Fe304, to the protoxide, FeO, before a true comparative basis is reached. Experience has shown that with about one-half D. & L. sinter on the charge the coke should-be cut about 10 per cent. This theoretical benefit is borne out by the practical blast-furnace results on a large scale in numerous plants. In fact, wherever this very important factor is ignored the evil symptoms of excessive fuel will be indicated,

Jan 11, 1914

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.&apos;-&apos; One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930&apos;s were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,&apos; so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By D. A. Stout

Mr. Chairman and Members of the Rocky Mountain Coal Mining Institute: Your Secretary has asked me to write upon a subject&apos; which is a most interesting one, and which has a very wide scope. In view of the great need for further decreasing costs at its coal mines, the Colorado Fuel and Iron Company began early in 1924 to experiment with methods of mining which had not previously been. tried out at its mines, and which were selected because of the greater possibilities for the concentration of the work, better grouping of workmen, and increased tonnage per workman, with a resultant increased efficiency, better supervision, and lowered costs. Because of the great competition of the day, means and methods must be provided by which fewer mines can be made to produce larger tonnages and at a lower cost. Western physical conditions are such as to make our problems far more complicated and not so easy of solution as compared to many of the eastern fields where conditions are more favorable for the operation of the mines. The dry condition of our Western mines on account of a relatively low humidity, and with additional gaseous conditions, makes the problem still more difficult to solve. A study of new methods was necessary before adoption, and this was particularly true of the method of extracting the coal. Where mechanical means are used, particularly in the coking coal mines of this state, due consideration must be given to the type, and machines or conveyors should not be installed solely on the basis of their performance elsewhere, without the knowledge of local influencing factors. In trying out the newer methods of extraction at our mines, very careful consideration has been given to the question of safety and the adoption of any new methods must provide adequate means of protection to employes, and be approved by&apos; the State Coal Mine Inspector. In any large industry there are a few outstanding operating costs, and usually the leading ones in their order are labor cost, material cost, and power cost. The things which we, hope to accomplish: 1. Reduce labor costs. 2. Reduce material costs. 3. Reduce power costs by the con 4. Reduce the amount of powder used per ton of coal produced. 5. Increase the lump percentage (particularly at the domestic mines). 6. Reduce accidents and annual compensation payment. 7. Reduce haulage costs. 8. Reduce cost for track work. 9. Reduce cost for timber and timbering, and increase the recovery of timber at a considerable additional saving. 10. Reduce the brushing costs. 11. Reduce the amount of rock hauled to the outside. 12. Reduce the cost for drainage. 13. Reduce the cost for ventilating. 14. Reduce cost of inspection and supervision. 15. Reduce the cost for shot firing. 16. Reduction of number of working places. 17. Grouping of men with increased sociability. 18. Increased tonnage per man. 19. Reduction in total number men employed. In the consideration of the methods used and now working successfully, there were three points which were considered outstanding, to make them wholly successful: ventilation, roof control, and transportation. For making the experiments, those mines were selected where conditions

Jan 1, 1925

By Jr. Flynn

"The Bureau of Mines receives and answers many requests for information on the qualities and properties of American coals, and also publishes many papers that deal with coal characteristics. Compilations of chemical analyses of coal from specific locations are contained in a series of technical papers,2/ by States, whereas typical analyses of coal seams, by States and counties, are given in data books, volumes 1 to 7,2/ by producing districts, as defined in the Bituminous Coal Act of 1937. Bulletin 446, ""Typical Analyses of Coals of the United States,"" condenses and supplements these data books, which do not apply to the Western States. Other coal properties are described in numerous publications listed in the Bureau of Mines Bibliography of Publications. However, no recent publication lists average B.t.u. values by rank on a Statewide and national scale. Averages have been estimated in the past, and some of them are included in this paper for comparison.The average and the ranges of as-received B.t.u. values of American coals on a Nation-wide basis, as found by the statistical method described in this paper, are given in table 2 and on a State-wide basis in table 3. The following is abstracted from table 2:In deriving average B.t.u. values for coals, the results depend on the type of data available and the methods of calculation. The data, or analyses, may represent any of three types of samples - mine, tipple, or delivered. In mine sampling, a channel cut is made of a vertical face of the coal bed, carefully excluding most of the impurities, and the material retained is the sample. It is readily seen that mine samples are selected samples and do not strictly represent the unmined coal bed, unless the coal contains no major impurities. Mine samples generally represent the best-quality coal that could be produced. In contrast to mine samples, tipple and delivered samples represent coal that actually has been mined, and their analyses may show either lower or higher values than mine samples of the same coal, depending on treatment and preparation after mining.Of the thousands of analyses accumulated by the Bureau of Mines, most are of either tipple or delivered samples and represent the coal after it has been mined. Any average calculated from this aggregate of data will, consequently, reflect coal that has been produced, and not unmined coal in situ.The method of calculating an average from the basic data also will have considerable influence. If there are three seams of coal in a county, the average analysis for the county is not necessarily the arithmetic mean of analyses of the three individual seams. For a probable average of unmined coal, the B.t.u. values of each seam should be weighted in proportion to the unmined reserves of each seam. In similar manner, an average for past pro¬duction should be weighed according to the past production for each seam. Figures for coal reserves are only estimates based upon geologic evidence and its interpretation. Production records are much more accurate than estimated reserves, although detailed production records for individual seams by counties are very few."

Dec 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been &apos;designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been &apos;designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult&apos;s law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager&apos; from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult&apos;s law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d&apos;Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,&apos; the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By D. E. Peacock, B. Harris

Thermal-expansion and electrical-resistivity measurements have been carried out below 400°K on niobium and two niobium alloys containing tungsten. For anonaly in the expansion us temperature curve below aboct 300°K. This reslt is consistent with an earlier obsercation that Young&apos;s modilus joy Cb-132 lms an unusiully strong -tenperati-e dependence below roon temperature. No anonulous behavior was observed in the resistiuity vs temperature curve for either alloy or in the magnetic susceptibility us tenperature curve for Cb-132. These results are disclssed in terms of various electronic and bonding theories of the transition metals and their alloys, but it has not been possible to reach any definite conclusion as to the cause of the results obtained. ALONG with investigations of the low-temperature mechanical behavior of niobium and its alloys, some of the physical properties of these materials have also been studied. In the work described here, thermal expansion and electrical resistivity were measured below 400°K for niobium and two of its alloys, Cb-132 and D-43. In addition, the magnetic susceptibility of Cb-132 was measured over the same temperature range. The alloys are representative of two distinct tion-hardened alloy such as might find service as a turbine blade, while D-43 (Nb, 5.3 at. pct W, 1.1 at. pct Zr. and 0.08 at. pct C) is a solution- and dispersion-hardened alloy, of considerably lower strength than Cb-132. which is a potential vane material. Their significant common feature is the presence of tungsten as the principal source of solution hardening. EXPERIMENTAL TECHNIQUES Thermal-expansion measurements were made with a quartz-tube dilatometer using baths of liquid nitrogen, liquid bromoethane, and a liquid polyalkylene glycol derivative to cover the range 80 to 400 K. Results are recorded as expansion relative to that of quartz, and the probable maximum error in any value of relative expansion. All, is about il pct. The metallurgical condition of the specimens, which were in rod form. will be discussed in the section dealing with experimental results. Resistivity was measured on recrystallized wires 0.030 in. in diam using a potentiometric technique. The same baths were used for temperatures between 80&apos; and 400°K as were used for the expansion measurements. and in addition the resistance of D-43 and Cb-132 was measured at 4.2 K by immersion in liquid helium. The maximum expected experimental error in any resistivity value is about 3 pct and that in any change in resistivity about i0.05 pct. Temperatures in both sets of experiments were measured with liquid-in-glass thermometers with an accuracy usually better than 1°K. EXPERIMENTAL RESULTS 1) Thermal Expansion. In Fig. 1 is shown the relative linear expansion of recrystallized niobium. D-43. and Cb-132. The curve for Cb-132 is composed of results from several runs on three different samples. Two of the samples were annealed for an hour at 1500°C to cause recrystallization and the third was annealed for an hour at 2000&apos;C to remove some mi-crosegregation of tungsten which was known to be present in the wrought alloy received from the manu-

Jan 1, 1967

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964