Search Documents

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By Peter C. Hayes

"The high temperature reduction of solids through the use of reactive gas atmospheres has application in a wide range of industrially important processes. Whilst significant advances have been made in understanding and describing these processes, some key aspects of the chemical reactions and reaction mechanisms operating in these systems, for example, the transformation from metal oxide to metal, remain poorly understood. A number of different product morphologies have been identified in these reaction systems and the reaction rates have been shown to be critically dependent on the product structure.Theoretical examination of the elementary process steps taking place in the region of the gas/metal/metal oxide interface, combined with electron microscope studies of the resultant product microstructures, have enabled the key process and material variables responsible for the development of the various product morphologies to be identified. By considering i) established criteria for the stability of moving interfaces in a thermodynamic potential gradient, ii) the relative rates of chemical reactions on the oxide and metal surfaces, and iii) key process phenomena and physico-chemical properties of the solid phases, the mechanisms and conditions for the formation of various product morphologies are identified. Interestingly the analysis points to direct analogies between these phase transformations and, the phenomena and microstructures observed in metal solidification, and the potential to develop generic models of these fluid/solid reaction systems."

Jan 1, 2013

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By J. M. Van Langen

In 1965 Hoogovens was looking for additional capacity for burden preparation in the order of 2,5 to 3 million metric tons per annum of some kind of optimal blast furnace ore feed. In principle four solutions offered them-selves for further investigation: 1. purchase of screened ore and/or run of mine ores with the provision of a corresponding ore screening capacity on the blast furnace site; 2. manufacture of sinter; 3. purchase of pellets; 4. manufacture of pellets. After studying the technological, technical, economical and commercial factors Hoogovens decided for the last mentioned possibility. Before taking this decision not only a great number of different mixtures of iron ore were tested, but during a long period in one of the big blast furnaces a number of tests were also executed with purchased pellets from South and North America. It was found, that using 50% acid pellets with 40% basic sinter a coke rate saving of 25 kg per ton hot metal (50 lbs/net THM) and a production gain of 15% could be obtained as compared with a full sinter practice. With some pellets it became clear, that due to properties, commonly referred to as swelling, we got very poor furnace performances; so in studying the production of pellets, pellet quality should be regarded as the most important aspect of the problem.

Jan 1, 1972

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By Leonhard Weixler, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep ground-water barriers, named Cut-Off-Walls (COW). It can be anticipated that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Therefore, there is the demand to minimize the size of equipment to accommodate such projects. Following this demand, a new trench cutter system, the so-called CUBE System, was recently developed. The complete trench cutter system has been fit into container size dimensions so that it can work in very limited space conditions. In addition, complex conditions in terms of space limitations require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Due to the limited space requirements, the impact on the surrounding environment is limited. As the system is electric driven, an additional reduction of carbon footprint can be expected. First tests of the system have been carried out and the results will be shared. The paper will explain the construction process and the specific challenges and experiences made for these extreme conditions.

Oct 1, 2022

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By Kenneth A. Grace

Each and every mining operation from a simple sand-and-gravel pit to the largest integrated mine-mill-concentrator-smelter-refining complex has, as its foundation, a quantity of extractable natural resource the reserves. Without reserves, there is no mine, and any concentrating or extracting plant, no matter how sophisticated, is simply so much scrap metal. And, of course, without resources there are no reserves. It is remarkable, therefore, especially in this age of careful planning, high quality engineering, and state-of-the-art financial analysis, that such a fundamental and vital item is so little understood and the subject- of so much confusion. Time and time again it has been the experience of the author, when called in to a mining operation that has run into trouble in reaching projected production targets, to find that the designed-for tons were not reaching the concentrator/extraction plant, and/or the grade of such tonnage was substantially below the forecast and design grade of the plant. The mill blames the mine for delivering below standard tons and/or grade and the mining engineer blames the geologist for overly-optimistic assessment or incorrect interpretation of the deposit. The geologist blames the mining and metallurgy division for wrongly interpreting his data and conclusions, or simply fouling-up a fine orebody.

Jan 1, 1983

By A. H. Castillejos E., F. A. Acosta G.

Filtration is widely used as a terminal refining step for metals, particularly for the casting of aluminum alloys, but still more knowledge is required to understand how several factors affect the efficiency of removal of inclusions. In this study, both, initial and long term filtration efficiencies of a ceramic foam filter have been obtained from the computed trajectories of solid particles suspended in molten aluminum. The complex structure of the foam filters is represented by a unit cell which is formed by a pair of pores with average dimensions. The fluid flow field was determined from the numerical solution of the Navier-Stokes equation, and periodic fully developed flow was assumed at the inlet of the calculation domain, as a boundary condition. This flow field corresponds to laminar flow as that found in ceramic filters operating under normal conditions. Computed initial filtration efficiencies showed that filtration efficiency decreases sharply with fluid velocity for particles larger than 30 µm, but smaller particles are better trapped at higher fluid velocities. Finally, it was found that long term filtration efficiency for particles of 8 µm decreased with time, in spite that perfect particle-wall attachment was assumed. Filter aging was considered in this study, and it was found that the distorted flow field, around the already trapped small inclusions prevented further collection.

Jan 1, 1999

By Ihsan Berk Tulu, Mark Alexander Van Dyke, Deniz Tuncay, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies, personnel, and the dilution of mine air contaminants. By design, these entries must stay open for many years for ventilation. Standing supports in moderate cover bleeder entries were observed, numerically modeled, and instrumented by researchers at the National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in this paper in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar, or supports are to the gob, the greater the applied load due to rear abutment stress.

Jan 7, 2021

By A. J. Schindler, F-P Sawyer, T. Logan, M. L. Shutey-McCann, R. M. Perry

"Test work on biooxidation pretreatment of low-grade refractory gold ores has been ongoing at Newmont Gold Company since 1988, including laboratory testing and pilot biooxidation heaps (360 to 23,000 tonne). Metallurgical results of the biooxidation process utilizing Thiobacillus ferrooxidans (T. ferrooxiddans) have culminated in the design, construction, and operation of a biooxidation demonstration facility. The facility has processed 708,000 tonnes of refractory ore, using a batched process with separate pads for biooxidation and ammonium thiosulfate gold extraction. Siliceous sulfidic refractory (SSR) and carbonaceous sulfidic refractory (CSR) ores are treated separately during biooxidation pretreatment unit operation. Following biooxidation, the ores are neutralization with lime and placed on oxide leach pads or stacked on the ammonium thiosulfate leach pad. Gold is leached with either cyanide for SSR ores or ammonium thiosulfate for preg-robbing CSR ores.This paper will only address the biooxidation pretreatment process of the SSR and CSR ores.AcknowledgmentsThe authors appreciate the cooperation and approval of Newmont Gold Company Carlin Operations management for its support and permission to publish this paper. The paper draws on efforts and assistance of the following people and several others which are to many to list who participated over the past five years in bringing this project to its fruition: Dr. James A. Brierley, Chief Microbiologist, Newmont Metallurgical Services; Dr. Rong-Yu Wan, Metallurgical Manager, Newmont Metallurgical Services."

Jan 1, 1997

By YONGQIONG YANG, Ning Wang, CHONGGUANG LUO, LI ZHU, Hanjie Wen, SHENGJIANG DU, Hannian Gu

Niobium in kaolin clay from the Late Permian sequences was reported in the range of several hundreds of micrograms per gram and was considered as a potential resource for its high concentrations and large areal distribution. Ti-bearing minerals associated with kaolin clay were identified as the main host phase for niobium in some case studies. However, the correlation between the concentration of niobium and titanium is poor, and the types of Ti-bearing minerals and modes of occurrence of niobium are not clear. Typical kaolin clay samples from the Late Permian sequences from southwest China were characterized, and the final products derived from kaolin clay sample were investigated using XRF, ICP-MS, XRD, SEM, and TEM (EDS). The results reveal that there were three types of TiO2 mineral phases in the clay samples: (a) massive TiO2 minerals and (b) aggregates of nano TiO2 minerals did not contain niobium while (c) granular TiO2 minerals were the source of niobium from the EDS analysis. The granular TiO2 minerals included anatase and rutile, both of which were the sources of niobium in kaolin clay in the current study. The findings are of great theoretical implication for source and origin study of Ti-bearing minerals and guidance for separation and recovery of niobium from kaolin clay.

Nov 30, 2020

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By James W. Wade

THIS discussion of the future supply of lead refers only to the next ten-year period. Beyond that no prediction can be made that would be of sufficient accuracy to serve any purpose. When any commodity is by an unsatisfied demand forced to a higher price level, and the profits of those who are able to produce the commodity are greatly increased, there is awakened a new interest in the commodity on the part of both producer and consumer. The consumer attempts to reduce his costs by developing substitutes or assisting in the development of new sources of supply. Lead is now going through this stage. The lead producer is increasing development expenditure and searching for new mines. The consumer is developing substitutes as illustrated by the increasing use of zinc oxide as a pigment, and the use of dry batteries in radio sets. The search of the Ford interests for lead, by prospecting in Missouri and Idaho, is induced by the effort to develop a new source of supply. Considering the index figures of the Department of' Commerce, it is evident that lead is on a substantially higher price level. For February, 1926, the index figure of lead is 209, while the general commodity price index is only 156, 100 being taken as the base for 1913.

Jan 1, 1926

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967