Search Documents

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By Serge Borel

An efficient design method is proposed for "piled-footing" and "piled-raft" foundation under lateral loads. It combines the methods used for the displacement design of shallow and deep foundations and takes into account the interactions between the piles and the cap or raft. This method has been applied to previous full-scale tests carried out in the United States. Two groups of six instrumented driven piles were laterally loaded several times: first with the concrete pile cap in direct contact with the soil, and then, after a thin layer of soil had been removed beneath the cap. The proposed method models well the real behavior of piled-raft foundations. It highlights the positive effect of the cap in contact with the soil, which reduces significantly the displacements and the maximum pile bending moments. These are divided by two for the analyzed case histories.

Jan 1, 2002

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By E. Topuz, M. J. McPherson, J. Banik

This paper summarizes the analyses of ventilation layouts for mines that experience both spontaneous combustion. The major focus is placed on the longwall coal mine layouts used in several countries. Each of the different layouts is modeled in the form of a ventilation network. The gob of a longwall panel is the most critical location for the occurrence of spontaneous combustion. Airflow leakage paths inside the gob are simulated by using a simplified grid-like network. Computer simulations with this model indicates that the W-system of ventilation is most effective in minimizing air leakage into the gob. Homer, the U-system of ventilation, with pressure balancing behind the face support line, is also found promising for longwall panels. The magnitude of air leakage into the gob is observed to change with the advance or retreat of bee, thus requiring appropriate balancing of pressure to maintain the leakage at a minimum.

Jan 1, 1995

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

Develop a metal substitute which is more plentiful and less expensive than the metals currently being used in high performance, permanent magnets, while maintaining the quality of the magnet. The New Alloy The rare-earth metal used in most high performance magnets is samarium, an expensive metal of limited availability. Cobalt is also used in high performance magnets, but supplies of this metal also are limited because it is not domestically mined and must be imported. The Bureau of Mines embarked on research to find a less costly domestic: metal source for use in industrial magnets. The alloy found most promising consists of mischmetal, a relatively abundant, naturally occurring mixture of rare-earths, which can be used as a replacement for samarium. Additives of copper, magnesium and iron used in combination with mischmetal aid in replacing some of the cobalt needed for the magnets.

Jan 1, 1983

By S. K. Kawatra

In order to take full advantage of the use of manipulatable variables to effectively control the response of coal flotation circuits to disturbances and to optimize circuit performance, the effects of each manipulatable variable must be understood with respect to the mechanisms responsible for particle recovery. This paper pays particular attention to the critical role of the froth phase and its effect on circuit behavior and control and emphasizes that in order to optimize the separation of coal from gangue by flotation it is necessary to consider particle behavior in both the pulp and in the froth while developing a control strategy. Data obtained from the extensive sampling of the flotation circuits in two coal preparation plants are used to illustrate this concept; by showing first the effects of reagent addition levels on the mechanisms responsible for particle recovery and second how this information can be used for control strategy development.

Jan 1, 1984

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By Laszlo Valentyik

To separate minerals on a small scale according to their specific gravity, heavy liquids are used, but because of high costs and health hazards they cannot be used in large scale plants. In order to substitute heavy liquids, finely ground solids like magnetite and ferrosilicon mixed with water and clay for the required specific gravity are employed. The clay present in the medium acts as a stabilizing agent since the coarse heavy media solids would sink very fast to the bottom of the container if they were mixed only in water. The optimum amount of clay varies for different processes, but it is generally between 3-6% by weight concentration of solids. As the pseudo-plastic nature of polymer solutions has excellent suspending properties, investigations were conducted at the Institute of Mineral Research to ascertain whether polymers could be used commercially as suspending agents for finely ground heavy media.

Jan 1, 1973

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By Herbert Pöllmann

The mineralogical and chemical compositions of various waste materials undergo different reactions when treated thermally The heavy metal contents can be bound to stable phases. These minerals are called reservoir minerals. The main property of these minerals is the stability in their geochemical surrounding containing the heavy metal cations and anions. Examples for these minerals are apatites, spinels, garnets, perovskites and also water containing minerals like ettringites, metal-metal-hydroxi salts, jarosites and zeolites. When the chemical compositions of different wastes are mixed according to the compositions of the new formed minerals, a probable reuse of these wastes can be obtained. The use of waste incineration ashes for the production of cementitious binders and the use of flue gas desulfurization products for cement additives are shown. Also the transformation of highly contaminated materials into stable reservoir mineral assemblages are shown including the study of stabilization and immobilization techniques.

Jan 1, 1998

By F. M. Doyle-Garner, A. J. Monhemius

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°C to 200°C (265°F to 392°F). Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions containing various metals, singly and in mixtures. Single solutions of Fe, Ni, Cu, Mg, and Mn precipitated [a]Fe2O3 Ni(OH)2 Cu2O + CuO, Mg(OH)2 and [?]Mn203 respectively, during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe204. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versatic solutions are similar to those for iron hydrolysis in aqueous solutions. Magnetic interactions between mixed carboxylate complexes are thought to be responsible for the homogenous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1986

By Richard R. Klimpel

This paper takes the liberation model recently developed by Klimpel and Austin for liberation from a binary system and reduces the over-all model form to a number of useful limiting cases. General use of the complete model form, while quite broad in utility, requires a numerical integration computer program for prediction of liberation given a specified minor component grain size distribution coupled with an optimization algorithm such as linear programming in order to back- calculate the associated grain size distribution from experimental data. In this paper, analytical solutions to the model are achieved for various assumed distributions of the minor component. These solutions are algebraic equations capable of predictive use with a hand calculator and back-calculation with very simple trial and error search procedures. The use of these special model solutions is illustrated on several sets of experimental liberation data, and the approach is shown to have practical utility.

Jan 1, 1984

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

By L. L. Karafiath, S. G. Vick, E. A. Nowatzki

Computer analyses of the trafficability of copper mine tailings by four different commercially available BWEs were performed. A mathematical model incorporating the tailings' Coulomb strength parameters and the vehicles' geometry and operational characteristics was used to study the vehicle terrain interaction. The computer output provides the maximum tractive force (net drawbar pull) that each BWE can develop for given tailings conditions without bnngzng about a state of plastic failure in the tailings. Estimates of sinkage are also provided. The theoretical results for the BWEs and tailings studied compare favorably with the operating experience of similar BWEs used for remining gold tailings in South Africa. This lends some confidence to the validity of the mathematical model. The results of such analyses may be wed to evaluate, on a relative basis, which of a number of different machines would perform better than others under given conditions of a tailings deposit.

Jan 1, 1982

By Martina Balic

Dynamic properties of the drilled shaft foundations supporting Doremus Avenue Bridge were determined by forced vibration testing. The main objectives of the substructure testing at Doremus Avenue Bridge were: (1) site evaluation with respect to the dynamic soil properties, and, (2) shaft evaluation for the purpose of definition of their dynamic stiffness. The site characterization entailed crosshole testing for the purpose of evaluation of the shear modulus profile. The drilled shaft impedance evaluation was done through forced excitation using an electromagnetic shaker. The responses of the tested shaft, as well as the response of adjacent shafts, were measured for the purpose of evaluation of the shaft interaction. To gain a better insight into the shaft dynamics, one of the shafts was instrumented with five triaxial geophones distributed along the full length of the shaft. The scope and results of the site characterization, shaft impedance and shaft interaction evaluation are presented.

Jan 1, 2004

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967