Search Documents

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By James R. Dunn

The mineral industry" has made and will continue to make important contributions to the growth of our economy. However, the industry is presently under continuous and increasingly severe attacks by organizations and individuals interested in the preservation of our environment. Yet neither the public interest value of preservation nor the public interest value of our mineral industry is known. In the absence of such values, judgments about best land use where minerals are involved are nearly always made on emotional grounds. An example of the sort of problem that has been created is in the New York Metropolitan Area. Because of institutionally-created shortages stemming largely from zoning decisions and building over deposits, the effective cost of fine aggregate delivered at dockside at Manhattan rose from $2. 65/cubic yard in July, 1969, to $4.10/cubic yard in May, 1970, this in spite of approximately ;l0,000 years of reserves on Long Island. The cost of fine aggregate for New York City alone has "Increased over $S million annually within one year, with the cost increase for the Tri-State Metropolitan Area (coastal Connecticut, New Jersey, and New York)" exceeding $10 million annually. The ab0ve situation has created a cost increase which is clearly the result of non-conservation of a mineral resource. That is, in readily measurable values, it Is costing the public about $10 million per year because good conservation practices were ignored-a public-interest loss. Admittedly, this is not the whole story because the public is simultaneously obtaining other values from the land surface that would otherwise have had to be dedicated, temporarily to be sure, to mineral recovery-a public-interest gain. However, the point is that we do not know where the balance lies-the net public interest value; it may lie one way for deposits zoned out of existence by a growing suburb, another for areas designed as permanent greenbelts, and still another for areas under new highways

Jan 1, 1971

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By R. J. Visintainer, J. M. Furlan

"Due to the time-consuming nature of froth testing in a laboratory environment, practical limitations require the development of a method of applying a single set of performance test data (Visintainer and Whitlock, 2012) obtained for a single froth pump at a given speed to a range of froth pump speeds and sizes, % air content and liquid viscosities. Head, efficiency and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique that can be used to interpolate from existing test data in order to predict froth performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal, as well as the insights gained from analysis of the resulting regressions, are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute standard for the effects of liquid viscosity on centrifugal pump performance (ANSI, 2010).IntroductionPump performance data (Visintainer and Whitlock, 2012) has been collected for a froth pump using an experimental loop outfitted with an array of pressure transducers, mass flow meters, an inverted U-loop, magnetic flow meter and an assortment of other instrumentation. Experiments were performed on pure water, water and air, pure corn syrup, and corn syrup and air. Data was obtained for % air contents of 0-30% and viscosities of 1- 15,000 cSt at eight specific valve positions (eight different flows as a percentage of best efficiency flow points) and the viscosity was changed by allowing the system temperature to increase during testing. The test pump is a 710-mm diameter impeller, GIW HVF, open shrouded, vented design that has its discharge axis oriented at 45° upward from the horizontal. A schematic diagram of the froth pump test loop can be seen in Fig. 1."

Jan 1, 2015

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By R. L. Grayson, W. E. Wallace, M. D. Attfield, A. Q. Wearden, P. Bolsaitis, R. D. Kennedy, M. J. Keane, J. C. Harrison

"Respirable high-silica particles from four coal mines. a clay mine and a tunnelling site were analysed for silicon vs aluminum composition by performing scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDS) at electron accelerating voltages of 20 kiloelectron volts (keV). The same particles were analysed at 5 keV to determine possible differences in surface vs bulk composition. In some cases high-silica particles exhibited a decrease in the ratio of silicon to aluminium K-alpha line intensities with decreasing electron beam accelerating voltage. This behaviour is consistent with aluminosilicate surface contamination or occlusion of a silica particle. Some 20 high-silica particles were analysed from each of 10 samples. Powdered aluminosilicate glass was used as a control for the behaviour of silica with a homogeneous distribution of aluminium in the particle. Significant differences were found between the control and sample means for an Illinois bituminous coal mine dust, two western and one central Pennsylvania bituminous coal mine dust low-temperature ashes. and a clay mine and mill dust sample, but not for an anthracite coal mine dust and two central Pennsylvania bituminous coal mine dust low-temperature ashes. INTRODUCTIONRESPIRABLE dust quartz content commonly is measured on bulk samples by using i.r. spectroscopy or X-ray diffraction. For research purposes, individual particle-by particle SEM-EDS analysis at 20-30 keV electron beam accelerating potential may be used also. Such measurements have not provided an unambiguous association of quartz content with occupational pulmonary disease prevalence in exposed workers (WALTON et al., 1977). Rather, there is evidence that coal rank modifies the relationship between dust exposure and pneumoconiosis development (WAL TON et al., 1977; ROBOCK and BAUER, 1990; ATTFIELD and MORRING, in press). SEM-EDS analysis was performed to measure the silicon fraction, Si/(Si +Ai), at 20 and at 5 keV on high-silica particles to determine if some respirable quartz particles generated by mining exhibit heterogenous composition with depth (WALLACE et al., 1990), which might affect the bioavailability of the quartz surface."

Dec 1, 1995

By E. M. Murphy

(Presented by invitation at a meeting of the Spokane Local Section of the Institute, Feb. 17, 1912.) EIGHT years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Coeur d'Alène district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8 by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown ; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Coeur d'Alènes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Sep 1, 1912

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By Du Sichen, S. Seetharaman, J. A. Bustnes

"The present study deals with the kinetic studies of reduction of some selected transition metal tungstates with hydrogen. The measurements were carried out by the isothermal thermogravimetric method. Shallow powder beds were employed in order to avoid the effects due to transport phenomena affecting the reaction rate. In this way, the chemical reaction rates could be selectively studied. The experiments were carried out in the temperature range 873 - 1173 K. From the experimental data, the activation energies were evaluated and were found to be around 88 kJ / mol in the case of both iron as well as cobalt tungstates indicating the similarities in W-O bonds in both cases. The activation energies obtained are discussed in the light of the position of the transition metal in the periodic table as well as the thermodynamic stabilities of the various tungstates.IntroductionThe tungsten containing hard metals, characterized by high density, belong to a class of two-phase metal matrix composites. While these types of materials have traditionally found their applications within the defence industry as armour-piercing projectiles, counterbalance in helicopters and military aircrafts, outer casings of hand-grenades, etc., commercial applications for this class of alloys also exist, including radiation shields, penetrators for the oil industry, turbines for turbo-jet engines and a wide range of sports related parts. A possible route to the production of these alloys is to reduce the tungstates such as FeW04, Co W04 and NiW04 using a reductant like hydrogen or carbon monoxide. In order to have a better understanding of the processes involved in the production, it is important to have a knowledge of the reduction kinetics for these tungstates. According to the knowledge of the present authors, while the reduction ofNiW04 by hydrogen gas has been investigated earlier in the present laboratorypl no systematic reduction study has been carried out previously for the tungstates of iron, cobalt."

Jan 1, 1996

By S Hawker, M Gibbs, A Craven

Current climate change projections suggest both an increase in the intensity of significant rainfall events and an increase in the variability of rainfall in some regions of Australia. It is necessary for mine site owners and operators to understand the effects that this potential shift in climate may have on their operations. The ability to maintain compliance with discharge regulations and operational security for those sites that rely on surface water run-off harvesting may be negatively impacted if some current climate change projections are realised. Although current regulations require the preparation of water management plans, these are generally developed using historical climate records for the site in question and as such do not give any indication of a siteÆs resilience to the influences of climate change.This study compares design and operational considerations for a case study mine site using historical rainfall records and modified records representing climate change projections. The future climate models are invariably broad scale and are limited in their capacity to be downscaled to a reasonable resolution for developing a site water balance. Instead the local historical data set has been modified to concentrate precipitation to peak periods and propagated through the model. The study looks at the siteÆs response to the potential changes in climate.It is shown that if current climate change projections are realised, this will have a significant effect on both the necessary size of designed surface water infrastructure and operational considerations on-site. A discussion is presented on the potential risks that climate change presents to mine sites and the range of options that could be considered to mitigate these risks. Depending on a number of factors, including location and risk profile of the owner/operator, resilience to climate change can be addressed as either a capital or operational expenditure (CAPEX/OPEX).CITATION:Craven, A, Hawker, S and Gibbs, M, 2013. Site water balance response to variable climatic conditions, in Proceedings Water in Mining 2013 , pp 211-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By FRABK HERVEY PETTINGELL

THE stock exchange and its functions is about as well understood by the average individual as the fourth dimension. What is a stock exchange? Divested of the rules and regulations by which it is governed, and the facilities it provides for the convenient handling of securities, it would be in its nude state nothing more or less than a meeting place for brokers. The stock exchange in America dates back to 1752, when a group of merchants of New York established a meeting place at the foot of Broad Street for the purpose of dealing in meal and slaves. The first definite orgarization, however, had its beginning in 1792 when 24 New York brokers signed an agreement not to buy or sell public stock for less than one quarter per cent. commission. From this small group has grown by gradual degrees, the greatest organized security market in the world, namely, the New York Stock Exchange. At the present time there are 27 stock exchanges in the United States and 5 in Canada. Based on the volume of business transacted, the Los Angeles Stock Exchange ranks 6th among them. This is attributable to the fact that strictly speaking Los Angeles has never been a stock exchange town, like some other large cities. Take for instance San Francisco, which supported one stock exchange from 1862 to .1882 and has since supported two. No city, by the way, should tolerate two stock exchanges at the same time. It is an economic folly and a senseless duplication that can be compared with rival telephone companies or competing street railway systems, paralleling each other's lines and always leads to trouble and confusion, and sooner or later one or the other falls by the wayside. While Los Angeles has had stock exchanges of one kind or another since 1896, none of them attracted much attention until 1899 when the present exchange was organized and it did not get well under way until along in 1906.

Jan 1, 1925

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By M. Härting, D. T. Britton, M. Nzikou Mamboukou

"Copper containing different types of nanocomposites have been characterized for nanolabelling and ID. Three types of the rare earth nanoparticles were used for this study, the oxide and the sulphur compound of the Eu and Tb. Characterization techniques uses SEM, and Raman for morphology, chemical composition, and optical characterization respectively. It has been shown that it is possible to include the rare earth particle in a copper matrix without damaging its physical properties. INTRODUCTIONThe development of new materials, often involves the addition of new properties without changing the beneficial properties of the original material (Chen et al., 2009; Khana et al., 2007; Patil et al., 2008). Nanocomposites are nanostructured materials, whose structural elements including clusters, crystallites or molecules, of dimensions ranging between 1 to 100 nm (Moriarty, 2001), or a composite material where one of the phases is a one, two or three dimensionally nanostructured material (Nanotechnology, 2006; Wang, 2001). Nanocomposite materials research is a fast growing area due to the high demand for materials for specialized applications (Edelstein & Cammarata, 1998), such as biolabelling, magnetic storage media, solar energy transformation (Jisen et al., 2004), and resistance welding applications (Bessergenev et al., 1997; Kwon et al.,2006).The properties of the nanocomposite materials depend not only on the properties of their individual parent materials, but also on their morphology and the interfacial characteristics. Thus, significant efforts have been focused on the control of the nanoscale structures via innovative synthesis approaches. Therefore, novel materials of unique properties may be obtained by combining properties from the parent constituents into a single material (Balan, 2006; Garcia et al., 2009). Possible effects of nanocomposites in the original material may include changes in the mechanical properties such as hardness , wear resistance (Rafaja et al., 1987), and electrical properties (Britton et al., 2003). The inclusion process may therefore be used to tailor materials to have particular mechanical, electrical and optical properties (Das et al., 2009). However, to fully understand the nanocomposite, it is necessary to study the fundamental properties of both the host matrix and the inclusions (Li, 2008)."

Jan 1, 2012