Search Documents

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Harold M. Smith

This publication summarizes the literature on the composition of petroleum, with special emphasis on naphtha and gas oil, and provides a source book for the known qualitative and quantitative facts on crude oil composition. The discussion points out the known facts from supposition, and suggests new researches needed in various areas.

Jan 1, 1968

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By Rob Jameson

"Although seismic retrofit is recognized as a key micropile application, widely-used reference documents do not clearly address design and testing recommendations for micropiles that are loaded primarily under seismic conditions. The principles of micropile design and construction and their application to seismic retrofit projects are well understood and executed by leaders in the field. As the micropiling market grows, a wider audience relies on the information presented by DFI and similar industry groups. State-of-practice updates appear periodically in conference proceedings, but examination of recent bid documents makes it clear that there are opportunities to improve the specification of load, deflection, testing and acceptance criteria on many seismic retrofit projects. Updates to the FHWA Manual or DFI Sample Specification that specifically address seismic retrofit cases would be useful tools to disseminate information and enhance the state of practice.Micropile Survey UnderwayAs one step in this process, I am distributing surveys to contractors and designers prior to DFI Super Pile ’09 (June 4-6, San Francisco) seeking recommendations for design and testing procedures applicable to seismically loaded micropiles. I am also requesting any existing references that could be promoted as a standard for these cases. Anyone interested in participating in this survey, should contact me at rjameson@malcolmdrilling.com. Seismic RetrofittingMicropiles are ideally suited to seismic retrofit applications. Their high-tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. They can be installed within and around the access limitations of existing structures, and can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones.Seismic retrofits have included micropiles since the early 1990s, and they are now widely specified in the Western U.S. In the San Francisco Bay Area alone, thousands of micropiles have been installed for seismic upgrades of highway and transit aerial structures, and retrofits of commercial, residential and public buildings. Micropile use is growing in both public and private sectors, with large-scale retrofit projects currently underway for both the Bay Area Rapid Transit (BART) system-wide upgrades and renovations at San Francisco Airport."

Jan 1, 2009

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By Atmesh K. Sinha

The demand for thermal coal both nationally and internationally is projected to increase rapidly. The marketability of high ETU thermal coal produced in the USA is, however, limited by its high sulfur content. Fortunately, over 70 percent of the sulfur exists in pyritic form. The research conducted at Southern Illinois University indicates that over 90 percent of the pyrite can be removed by simple devices such as concentrating tables, cyclones, or froth flotation cells and the desulfurized coal can be blended with low sulfur western coal to produce EPA compliance coal. Thus, both the low BTU western coal and the high sulfur midwestern coal can be rendered competitive in the utility markets, here and abroad due to improved utilization.

Jan 1, 1983

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By G T. Jemwa, F Rousseau, F J. Wolfaardt, J A. M Rademan, P W. Smit

Mining companies are increasingly faced with the challenge of reducing operating costs while maximising throughput and profitability. At the same time, the grade and quality of treated ores are becoming poorer and more variable, resulting in suboptimal process performance.It is now widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In particular, progress in plant automation and control systems has seen a trend towards unified frameworks for control and optimisation of mineral processing plants. These frameworks seek to seamlessly integrate different roles and tasks involved in process operations - IT, automation, plant maintenance and operations. An integrated solution framework for reducing process variability, increasing process efficiencies and maximising plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis ægapÆ evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.Resolving these problems can potentially avoid unplanned downtimes, process instabilities and other operational surprises, thus ensuring optimal plant throughput and optimal process behaviour for improved recoveries. Integrating control systems and plant automation with advanced analytics to analyse and optimise processes enables operations to achieve reductions in the variability of key process parameters. In addition, early detection of equipment malfunction or suboptimal process conditions leads to improved equipment availability and reliability. Ultimately, these operational gains reflect in profitability because of plant throughput and recovery gains. These benefits are demonstrated using data from a South African gold mining operation, where such an integrated asset and process health monitoring framework for process optimisation has been implemented.CITATION:Jemwa, G T, Wolfaardt, F J, Smit, P W, Rademan, J A M and Rousseau, F, 2013. Towards an integrated framework for asset and process health monitoring and optimisation on a milling circuit, in Proceedings World Gold 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

The topic for my address is Sharemarket Floats - Issues for Expert Valuers. I've decided to focus on three areas where current practice in the preparation of prospectus valuation reports for resource companies might be improved. My central theme is that the valuer for a float should augment the usual assessments of the value of the company or its assets, with some input on the way the share market might value the company's shares when they are listed. I will then look at the valuer's role in relation to vendor consideration, last I will look at his role in providing investors with some input on the risk dimensions of the new company.

Jan 1, 1989

By Elizabeth Gardiner

Tailings and water management facilities are integral components of mine and mill operations. They must be managed for the long term to ensure that safe and environmentally responsible stewardship is achieved. The Mining Association of Canada (MAC) has developed and published two manuals to provide guidance to mining companies on sound practices for the safe and environmentally responsible management of tailings facilities: ???A Guide to the Management of Tailings Facilities; and ???Developing an Operation, Maintenance and Surveillance Manual for Tailings and Water Management Facilities. The Guides were designed to help companies develop and implement tailings management systems that include environmental and safety criteria, to improve the consistency of application of sound engineering and management principles to tailings and water management facilities through their full life cycle, and to demonstrate this to regulators and the public.

May 1, 2003

By Minna Päällysaho

For the first time, the idea of sustainable development was recognised at a high political level at the UN Conference on Environment and Development held in Rio de Janeiro in 1992 (UNEP, 1992). Then the governments of the world committed themselves to promote sustainable development in their national activities and international co-operation. In 2001, the European Council approved the EU Strategy for Sustainable Development (European commission, 2011). This complements and supports the EU?s so-called Lisbon Strategy (European council, 2000) on competitiveness. The revised Strategy for Sustainable Development was approved in June 2006. Recently sustainability has had an important role in policy and decision-making while the public awareness towards limits of the environment has been rising. However, the indicators of industrial sustainability satisfy primarily the needs of corporate management and global investors. The information is often broad and non-specific and might occasionally even give a false impression. Moreover, contradictions between environmental, economical and social aspects also point out the unreliability of existing sustainability indexes. Therefore, the current state of affairs serves the interests of neither the industry nor the policy makers. Current corporate sustainability indexes and indicator systems need to be assessed with scientific methods encompassing the identification of their strengths and weaknesses. This requires quantitative and qualitative assessment and synthesis of existing indexes and indicator systems, providing new data on the functionality of existing corporate sustainability indicators. Therefore, the assessment lays the foundation for the development of new, more balanced sustainability index. Our first aim in this multidisciplinary article is to analyse existing global sustainability indexes for process industry. Second, we will introduce a first version of a new sustainability index for process industry, which includes the environmental, social and economic impacts of the plant, as well as legislation aspects.

Sep 1, 2012

By S. Wimpfen

El presente texto señala la adecuación de las reservas y recursos mundiales de cobre y aluminio para abastecer las necesidades mundiales de los mismos hasta el año 2000 a través del registro y análisis de las relaciones históricas que existen entre el crecimiento de la población y el crecimiento económico, consumo del metal, producción, reservas y recursos durante el período de la Post Guerra II. Así como la comparación de los requerimientos acumulativos de cobre y aluminio con los últimos estimados de reservas y recursos mundiales, según el Departamento de Minas de U.S.A. y el Levantamiento Geológico de U.S.A.

Sep 1, 1978