Search Documents

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By Yuchen Wu, Purushotham Thkkaraja, Marek Borowski, Jie Liu, Jianwei Cheng, WANCHENG ZHENG, Yu Wang, Weidong Lu, Gang Zhao, Zhanyou Sa, Huan Yang, Yuhang Wu, Hui Wang

The abstract discusses the importance of gas drainage in coal mines for safety, environmental protection, and resource utilization. It highlights the significance of borehole sealing technology for efficient gas drainage. The study introduces a new inorganic retarding sealing material and investigates its properties, including stability, thermal stability, fluidity, and thixotropy. The material's diffusion performance in cracks is tested using a self-designed system. Field tests in a coal mine demonstrate the material's effectiveness in improving borehole sealing compared to traditional materials.

May 1, 2022

By B. Stewart

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods, and better hang up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste rock loads on chutes, walls, gates, and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mock-up of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com-pared. Loads on an active ore pass chute were measured.

Jan 1, 1998

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By Cemal Can Maslak, Vijaya Bhushan Rao, Vidyaranya Bandi, Karsten Beckhaus

A Large Earth Cum Rock Fill, ECRF Dam is under construction at Polavaram in the state of Andhra Pradesh in India as part of an irrigation project. The Embankment crest width of the dam is 12.5m and base width is of approximately 136.75m with a stepped sloping height of 27m on both upstream/downstream sides. Once the 1.2m Thick Plastic concrete cut-off wall is constructed below the dam along the longitudinal central axis to avoid seepage, this magnificent structure will be supported on a series of Deep Mixing Columns and Stone Columns that are evenly arranged under the footprint of ECRF Dam forming a smooth transition of gradually reducing stiffness moduli of treated ground from the center of the embankment, where the foundation stresses are high, towards the edges in order to be able to progressively limit the settlements under the dam to a specified allowable limit. As such the required post treatment stiffness in case of stone columns is 2 times of the in-situ stiffness of foundation soil, whereas it is expected to be 5 times improvement for Deep Mixing as per project specifications. Laboratory testing and Field Trials undertaken successfully to verify the design.

Sep 1, 2022

By R Shaw, T T. Neidel, C Adams

Sampling equipment manufacturers endeavour to ensure that the mechanical equipment installed in sampling systems are designed and manufactured to adhere to the requirements of the International Organization for Standardization (ISO) or other standards relevant to the application. The mechanical parameters necessary to achieve these standards can be well controlled and requirements such as constant speed can be met through good mechanical design and engineering. However, when the equipment is installed and put into operation, the ISO compliance of the system is out of the hands of the equipment manufacturer and handed to the operator, who may be a generalist control system integrator.Making a sampling system perform according to standards, and being able to monitor and report on compliance require that the sampling system knowledge and the control integration is combined and applied in an integrated approach. Using a dedicated library of control routines developed for sampling can change a system from having compliant equipment to being a compliant system. The library has to include monitoring of relevant parameters and control and reporting on sampling parameters.CITATION:Neidel, T T, Adams, C and Shaw, R, 2014. Control and monitoring of International Organization for Standardization compliance for industrial sampling systems, in Proceedings Sampling 2014 , pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By A. P. Squelch

The high incidence of accidents and fatalities in the South African mining industry, in particular those associated with falls of ground, is often attributed to ineffective and/or inappropriate training methods and material. Recently introduced mine health and safety legislation in South Africa also requires that all mine workers receive appropriate and effective training to enable them to operate safely in their given mining environment. There can, therefore, be no doubt that methods to provide effective training, in particular safety related training, are urgently required in the South African mining industry. In the search for alternative and improved training approaches, attention has fallen on virtual reality (VR) technology as a possible solution. VR has found acceptance in a number of industries as an effective method of training for a variety of work place activities, including those of a safety related nature. VR has successfully been applied in a number of industries to improve the effectiveness of safety and hazard awareness training. The CSIR: Division of Mining Technology (CSIR Miningtek), in conjunction with the Safety in Mines Research Advisory Committee (SIMRAC), therefore evaluated the potential of VR to be used as a training medium in the South African gold and platinum mining industry. Aspects of the evaluation included an assessment of the technical capability of VR to represent a typical underground mining environment with sufficient realism and the relevance of the VR training concept for a largely illiterate workforce. For these purposes, a prototype PC-based VR hazard awareness training simulator has been developed by CSIR Miningtek, and a series of evaluation sessions conducted at a typical deep level gold mine. The conclusion from this evaluation work is that virtual reality technology has the potential to provide effective training systems that are relevant to the South African mining industry. Keywords: Virtual reality, mine training, safety training.

Jan 1, 2001

By Phillip A. Armstrong, Charles A. Lewinsohn, John H. Gordon

"This paper describes the opportunity offered by employing systems based on mixed conductive ceramics, in particular, ceramics conductive to oxygen ions and electrons, in reducing CO2 emissions from metallurgical production. Membranes based on these mixed conducting properties enable commercial viability of several attractive metallurgical processes. One of these processes utilizes modular, ceramic-membrane structures for the generation of pure oxygen, in tonnage quantity. The membrane-based systems offer significant capital savings and operating efficiencies in various metallurgical processes. The current status of this technology is summarized below.IntroductionCryogenic oxygen supply technology is currently the state-of-the-art for applications that require large quantities of oxygen (hundreds to thousands of tons per day). Cryogenic technology, however, requires substantial energy inputs and, hence, adds significant costs and emissions to processes. Furthermore, cryogenic oxygen supply technology is mature and there is relatively little potential for substantial capital cost reduction or efficiency improvement in coming decades. Non-cryogenic technologies offer a means to reduce the environmental footprint and cost of the oxygen supply facility in various applications.Ion Transport membranesCommercially available non-cryogenic air separation technologies, such as adsorption-based and polymeric membrane-based methods, do not afford the economies of scale that the cryogenic distillation enjoys. Therefore, industrial gas industry researchers began searching for alternatives to the relatively inactive and unselective polymeric membrane materials available. In the late 1980’s, Air Products began developing a new class of highly selective membrane materials with exceptionally high activity for oxygen transport. The materials constitute a class of oxide ceramics, and conduct both oxygen (as oxygen ions) and electrons in the same membrane, separating oxygen from air electrochemically. Numerous detailed process economics studies have shown that, based on these ion-transport membranes (ITM’s), the cost of oxygen can be reduced by approximately one-third relative to that obtained from state-of-the-art cryogenic oxygen supply technology, through a combination of capital cost savings and efficiency improvements. [1,2,3]"

Jan 1, 2008

By B. Mishra

Calcium and lithium gallides have been synthesized by powder metallurgy techniques in the stoichiometries that can be used as reduction alloys for the Rocky Flats Plant Salt-Scrub (SS) process. The SS process is performed to recover valuable metals from salts generated in the electrorefining and the molten salt extraction processes. Combustion synthesis has been optimized for variable heating rates up to the reaction ignition temperature and for green densities of the powder compacts in terms of the ignition temperature and the exothermic heating of the product in an effort to develop LiGa and CaGaz alloys. The problems arising from the melting point and density differences of calcium, lithium and gallium have also been studied. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. The efficiency of the intermetallic alloy, Ca-17 wt. pct. Ga, as a reductant and the effect of gallium on salt clean- up has been discussed. Measurement of actinide recovery has been studied with cerium as the surrogate for the actinide metal. The development of an alloy for SS reduces a major contaminated waste disposal problem besides recovering the valuable reactive metal.

Jan 1, 1993

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M. Beus, S. Stewart, S. Iverson

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods and better hang-up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mockup of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were compared Loads on an active ore pass chute were measured

Jan 1, 2000

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By Andrew P. Gize

The analytical approaches used to solve a specific problem are dependent upon the information required, coupled with limitations imposed by available facilities, costs, and time. The organic matter associated with ore deposits has the potential to yield information for two problems. Information can be obtained to provide guidelines for prospecting, and, secondly, to solve genetic problems. A major potential of organic matter in providing prospecting guides lies in the high thermal sensitivity of organic matter in sediments which are metamorphosed at grades lower than greenschist facies. The organic matter can then be used to map thermal anomalies potentially associated with mineralization. The analytical approach is to determine the thermal maturity of the total organic matter, or of specific fractions, using techniques which are relatively quick and inexpensive. Consideration of genetic models (for example, reduction, complexing, involvement of oil field brines) generally requires more specific information than the overall thermal maturity of the organic matter, necessitating infor¬mation on molecular composition and structure. The facilities, time, and cost of this information are greater than for mapping thermal anomalies. The analytical techniques discussed include elemental analyses, spectroscopy (infra-red, visible and ultra-violet), Fourier Transform infra-red, nuclear magnetic resonance, extraction, pyrolysis techniques, chromatography and mass spectrometry.

Jan 1, 2013

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By M. Scobie, T. Atkinson

"This paper reviews the development of new designs in extensible and high angle conveyor systems. These aim to overcome the limitations of prior alternative concepts in design. The application of such systems in strip, terrace, open pit and mountain mining is reviewed. IntroductionTruck haulage costs have tended to escalate in recent years. This has been primarily due to operations generally moving to greater depths with associated increases in haul distances . Periods of high inflation rates have also been experienced for diesel fuel oil, tires and other petroleum based products. Recent international political events have tended to regenerate concerns over future oil supply and price stability. For such reasons, conveyor based transport is becoming increasingly attractive. Truck haulage maintains an inherent flexibility and improvements continue to be made in performance and capacity. Doubts must exist, however, over the extent to which further economies of scale may be made. Conversely, belt conveyor systems do not suffer this constraint and have the following advantages:• Electrical power is used and the specific energy consumption is at least half that required for truck haulage.• Operating costs and skilled labour requirements are lower.• Equipment has superior longevity and is ""inflation proof"" .• Access roads can be steeper and narrower in most mine environments, reducing construction and maintenance costs.• They are less prone to breakdown and bad weather delays .• In long haul, high capacity operations conveyors can save substantially on capital cost.• Environmental impact is improved with reduced noise level, dust and atmospheric pollution. Although conveyor systems are less flexible in operation than truck haulage and although a breakdown in any part of the system can immobilize the total system, mechanical availabilities of + 80% are constantly reported by large operators. There would appear in the past to have been some prejudice against conveyor systems in hard rock mines due to lack of experience. Apparent reservations would apply equally 10 underground coal mines, yet practically all of these mines (and some underground hard rock mines) find conveyor systems more economical than other transport systems."

Jan 1, 1991

By Patrick R. Taylor

Glass is used for immobilization of radioactive and hazardous wastes due to its durability and ability to accept a variety of waste constituents into its network structure. Alternative high temperature vitrification techniques have the advantage of increased throughput, increased waste loading and being applicable to variable and heterogeneous waste streams. However, the increased processing temperature places further concerns on the increased volatilization of contaminants, and increased corrosion and erosion of me Iter components. A database of melt properties at higher temperatures, such as partitioning, viscosity, density and electrical conductivity, in the temperature range of 1400-20000 K are being developed.

Jan 1, 2000

By R Coleman

The flotation mechanism plays a key role in the flotation process. It is used to provide the contact between solid particles and bubbles and also the energy for these particles and bubbles to attach. The mechanism must therefore provide sufficient mixing to keep the solids in suspension so that they can be transported into the froth and recovered to the concentrate. The design of the mechanism is critical and over the past decade Outotec has developed and optimised a new mechanism design to improve metallurgical and energy performance. The FloatForce® mechanism consists of a rotor and stator arrangement and has been specifically designed to provide sustained mixing at higher air flows and lower power inputs.Over 500 FloatForce® mechanisms have been installed in existing and new operations. This paper outlines the technological aspects of the FloatForce® mechanism and provides metallurgical, operational and energy performance results from a number of flotation circuits in which these have been installed.

Aug 8, 2011