Search Documents

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By P. S. Dash

With implementation of stringent environmental regulations, ultra clean coal technology development programs have gained significant importance worldwide. As far as Indian scenario is concerned, most of the coals present in India are of drift origin and low grade, containing high mineral matter varying from 15% to greater than 50%. The inorganic or ash constituents of Indian coals are finely disseminated through the organic or carbonaceous constituents so, that commonly used physical beneficiation techniques are of only limited value in affecting separation. Chemical processes involve addition of chemicals, which react with the mineral matter and allow its easy removal. The present study envisages the effect of aqueous alkali leaching followed by acid washing on the removal of mineral matter from two different captive coals of Tata Steel at elevated temperature and pressure. The experiments are conducted at desired conditions using a bench scale pressure reactor set up having proper data acquisition and control system. The research study revealed, that it is possible to reduce the ash content up to 70% by this method. The alkali content of the product clean coal does not increase whereas the silica and alumina content reduces by nearly 58% and 62% respectively. Significant reduction in the phosphorus content is observed after the acid treatment. The crucible swelling number of the feed coal improves after the treatment. The mechanism of demineralisation was evaluated by analyzing the coal samples before and after the alkali and acid treatment using scanning electron microscope (SEM). Because of the acidic nature of the silicates and aluminates, they dissolve into the NaOH solution and form sodalite. Sodalite is partially soluble in the alkali solution. The hydrates formed during alkali treatment are partially removed due to acid wash. This study in overall provides an insight into possible alternative methods of beneficiation for removal of ash from high ash Indian coals.

Sep 1, 2012

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen's Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By T M. Campos, H A. Petit, L M. Tavares, R Olympio

Much practical experience has been gathered in the last 30 years of application of high-pressure grinding rolls (HPGR) integrated with ball milling in size reduction of fine iron ore concentrates. The company Vale S.A, in Complexo de Tubarão (Brazil), was one of the pioneers applying the technology prior to pelletisation with an outstanding size reduction energy efficiency in the circuit and a significant increment in the specific surface area of the product. Recent studies by the authors demonstrated benefits of modelling and simulation to improve the performance of HPGRs in this particular application, with the model being able to describe HPGR performance under different operating conditions and under variations of feed size distribution. Despite these important advances, this modelling approach has only been used offline and under steady-state conditions. The present work applies the modified Torres and Casali model proposed by the authors in pseudodynamic simulations. The ability of the model to predict the characteristics of the product in real-time is evaluated using data available online for the pellet feed preparation circuit. Results demonstrated the model capabilities to map the physical operation and give a realistic representation of the process. Additionally, the model is demonstrated to be able to support the pellet feed production by providing extended real-time information of the process, making it a useful tool for improvement of the operational strategies and process stability.

Aug 24, 2022

By V. T. BERNER

THIS apparatus was designed primarily to meet the demand for a quick, efficient stopping to seal off the burning area temporarily during a mine fire, but it can be used in any circumstance where an immediate brattice is required for ventilation control. In using the old style brattice, mine-rescue workers have found it difficult, in smoke-laden drifts and stopes, to erect an effective stopping with wooden frame and canvas. Stulls must first be cut to the proper length, the canvas tacked in place, and the numerous irregularities of the walls and back must be caulked. This operation requires the employment of axes, saws, and hammers, which cannot easily and safely be handled in dense smoke. The fire fighters have often been forced to abandon their brattice, unfinished, because of the rapid approach of the fire, or because of the exhausted sup- ply of oxygen in their breathing apparatus. It is neces-

Jan 1, 1930

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division's Toronto meeting in April, 1960. In bringing the power engineer's viewpoint to the coal producers' attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By Brenton Cook, Daniel Mageau, Larry Applegate, Aaron McCain

"Ground freezing was successfully used to create an impermeable barrier wall along 3,000 feet of the downtown Seattle waterfront as part of the Seattle Seawall Replacement Project. This $360 million re-development involved removing the original 1930-era seawall and replacing it with a new, seismically resistant concrete wall supported on fill soil improved by jet-grout. The replacement wall was one of the largest construction projects in the state of Washington at the time. Ground freezing is typically used as both a structural shoring wall and groundwater cutoff. However, at this project it was used primarily as a cutoff wall to stop groundwater seepage into the 16-foot deep excavation from the landside areas.The project was divided into ten boxes (sections), each typically 200 to 600 feet in length. Only a few boxes were under construction at one time to reduce the impact on tourist-dependent local businesses. Soil conditions in the freeze zone consisted of sand, gravel and silt fill with abundant wood and debris. Tidally influenced groundwater, much of it contaminated, was difficult and expensive to control using wells during initial stages of construction. For all subsequent stages, a frozen soil wall extending to about 35 feet in depth was used to stop groundwater seepage into the excavation. An additional benefit of ground freezing included elimination of potential settlement beneath nearby buildings, utilities, and the Alaskan Way Viaduct that would likely have occurred with the use of conventional dewatering wells. The frozen soil wall crossed more than 130 buried utility locations (including water, sewer, storm, electrical, fiber optic, phone, gas, steam) with no damage. The frozen soil wall was very successful and limited groundwater influx from the landside to the seawall excavation to a negligible amount so that pumping, storage and treatment of contaminated groundwater was essentially eliminated."

Jan 1, 2016

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006