Search Documents

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Gerhard Richter, Norbert Asamer, Gerwald Decker

At various stages during their manufacturing processes - from casting to finishing before delivery - semi-finished steel and special alloy products must be cut and surface-treated as well. The requirements for the individual conditioning steps, however, can be quite different. For example, the work piece can be hot, warm or cold. At any rate, the product must always be perfectly prepared for the next manufacturing step - reliably, in the shortest-possible time and at the lowest-possible cost. For cutting and grinding, BRAUN has developed innovative technologies and highly flexible, tailor-made solutions which meet these requirements in the most optimal way. In particular, BRAUN’s cutting and grinding technologies can also be used for large-scale products.

Oct 1, 2019

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By A. A. Schipaanboord, S. J. Dasselaar

"With the growing global demand for strategic metals, commodity prices are rising and the scarcity of some metals is increasing. Europe’s technology sector is also affected by this growing shortage of metals. Securing the supply of critical metals is now a major element in Europe’s economic strategy. The Blue Mining and Blue Nodules projects have been initiated to principally advance deep sea mining technology beyond current TRL-levels.These critical metals are found inside so-called “polymetallic nodules”, lying on the seafloor in deep-sea environment. These nodules have a typical abundance of 10-25 kg/m2 and a size range of 10-125 mm.Harvesting the polymetallic nodules is challenging. Two main methods of harvesting or collector equipment are distinguished: hydraulic and mechanical. Over the last year, Royal IHC has designed, build and tested a full-scale hydraulic collector. Meanwhile, a mechanical collector is being developed.First, a scaled version of the hydraulic collector was developed and tested in order to have a proof of principle. The development as well as optimization were aided by multiphase CFD simulations."

Jan 1, 2017

By O Bøckman, E Thisted, K H. Esbensen, U Thisted

Process industry measurement systems, once installed, are often interpreted as static black boxes delivering correct values as long as not proven otherwise. After first implementation and set-up with a distinct sampling frequency, they often run ‘forever’ without checking if this frequency is still appropriate with respect to changed raw materials characteristics, different process conditions or changed customer specifications. Failure detection is based on operator experience and skills (often close to an art form) and/or from control measurements of reference samples. This may well be too late for many industrial process contexts. An appropriate sampling frequency is a critical success factor for valid monitoring and control.Based on the methodology of variographic analysis we here illustrate how to design/re-design/optimise an industrial measurement system in terms of sampling frequency, discretisation and accuracy based on customer specifications. We also show how variographics can be used to monitor for deviations. We use experience from process industry to show how these methods can be used not only for product characterisation, but also for monitoring input factors, process indicators and measurement of these. The information hidden in the vast amounts of data that is continuously created in modern process industries can be utilised to cut costs in the measurement activities and at the same time contribute to early error detection. We illustrate by case examples from production processes at a nickel refinery, supporting the Lean and Six Sigma methodology. This will provide a standard operating procedure for monitoring the stability of measurement systems, and provide a basis with which to discuss how a variographic approach can be integrated with the Lean and Six Sigma approach as an online tool to map, characterise and validate measurement systems and thus avoid more cumbersome measurement system analysis in full detail.CITATION:Thisted, E, Thisted, U, Bøckman, O and Esbensen, K H, 2017. Variographic case study for designing, monitoring and optimising industrial measurement systems – the missing link in Lean and Six Sigma, in Proceedings Eighth World Conference on Sampling and Blending , pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M. Vondersaar, B. Bulnes

Quemetco, Inc.,. as a subsidiary of RSR Corporation, operates one of RSR's three secondary lead smelters in the City of Industry, California, next to a residential area within Los Angeles County. The Reverberatory furnace serves as the main reactor for melting lead grid and paste recovered by the battery crushing system. Feed material is introduced via screw conveyor after drying in an upstream rotary kiln. Slag produced by the Reverb flows directly to an electric arc furnace. Products from this one-pass furnace system consist of soft lead bullion from the reverb, hard lead bullion from the arc furnace, and a non-hazardous slag from the arc furnace. Furnace bullion is processed into finished product in a six-kettle refinery. An overview ·of plant operations is presented. Where applicable, references will be made to changes that have taken place during the last decade.

Jan 1, 2000

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By N. W. Xu, C. Sha, F. Dai, Y. G. Zhu, B. Li

Underground caverns stability and excavatability of rock masses are of significance in geotechnical engineering, in both design and construction stages. Risks associated with underground group caverns of Houziyan hydropower station in southwestern China are growing as a result of continuous excavation-induced unloading. To improve our understanding of the underground caverns instability and resolve the complex subsurface conditions of the highly fractured rock mass, a high resolution microseismic monitoring system was established in the deep underground caverns, pursuing the relationship between the measured data about microseismic activity and excavation damage zones of surrounding rock mass. Through analyzing the tempo-spatial distribution of microseismic activity, excavation damage zones and potential risk regions in underground caverns were identified. Furthermore, the correlation between microseismic activity and pre-existing geological structures, as well as traditional monitoring was analyzed. In order to validate the correlation between seismicity and potential slip surface of underground caverns, a model was implemented into numerical code to further evaluate the deformation and stability of surrounding rock mass. The monitoring results demonstrate that microseismic events mainly occur at high stress concentration regions, which coincides with the results obtained from numerical analysis. Therefore, the comprehensive method incorporating microseismic monitoring and numerical analysis, as well as traditional monitoring and filed observation has been proven to be very promising in deformation and even instability prediction of surrounding rock mass in underground caverns subject to delineation of potential slip surfaces and excavation damage zones.

Jan 1, 2015

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By A. C. Freeze

The first use of electric punched card accounting machines as an aid in calculating reserves at the Sullivan mine in Kimberly, B.C., was made in January, 1948. At that time their use was limited to totalling individual reserve blocks for the various reserve classes and for calculating total metal content. The immediate objective was to increase speed, improve accuracy, and to effect some savings in labor that could be employed more usefully elsewhere. It was recognized also that the potential for achieving even greater advantages was excellent. The initial experiment proved so successful that it was inevitable that the use of the method would expand. Thus, for the past nine years assay data from core hole and development headings have been processed by these machines and the results integrated with the program of calculating reserves. It was also learned that the machines could store and classify a large amount of other information concerning the mining characteristics of each reserve block in addition to tonnage and metal content. This has proven very useful for the preparation of monthly production reports as well as in long term planning, in forecasting production schedules, and in analysing the results achieved.

Jan 4, 1961

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003

By Bragg R, McMahon B, Lenton R

In 1992 environmental audits were carried out at seven coal mines operated by Oakbridge Limited in the Hunter Valley and Lithgow areas of NSW. The audit reports recommended a course of action designed to improve the environmental management system already in operation at the mines. This program started with training in environmental awareness for the Board of Directors, and the development and authorisation of an environmental policy. On-going programs at each mine were expanded to include environmental awareness training for all 2000 employees at the mines, and the development of a 20-module environmental training program which included air, water, soil and noise management, oil and chemical handling, sampling and monitoring, rehabilitation techniques and many more. Environmental incident reporting was introduced, and a system of reporting from the coal face through individual mine site environmental committees, to a Corporate Environmental Committee and up to the Board Environmental Committee became an effective part of a due diligence program. The Board resolved to undertake external independent environmental audits every two years, with internal reviews in the alternate years. An Environmental Management Group was formed, consisting of four internal environmental personnel and Oakbridge's appointed environmental consultant, to effectively resolve many of the environmental issues facing the Group. This program is continuing to evolve as an industry leader in environmental management Practice.

Jan 1, 1995

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By R Turner, P Hatherly, T Medhurst

Borehole geophysical logging data are routinely acquired during exploration of coal deposits in Australia. These data are commonly used qualitatively to identify and correlate coal seams and geotechnically significant interburden rock units. Some quantitative analysis, such as using sonic logs for rock strength estimation is becoming increasingly widespread. This paper discusses results from a project aimed at expanding the quantitative approach to more detailed mineralogical and lithological analysis, which leads to improved geotechnical characterisation for mine planning and mining hazard reduction. A standard suite of wireline logs measuring density, natural gamma, sonic and neutron were analysed from three coal mines in the Bowen Basin. Thirty-nine samples from cored sections of the boreholes were analysed by X-ray diffraction, spectral gamma counts and hyperspectral scanning. Using a standard petrophysical approach to calculating porosity, shale and matrix components from a combination of density, natural gamma and neutron logs, a good correlation with observed mineralogy was demonstrated. However, unusual mineralogies such as heavy minerals or low-potassium clays may distort this analysis. Simultaneous evaluation of all available geophysical logs by modern data mining methods was able to show how these ambiguities may be solved.

Jan 1, 2006

By J Boland

Polycrystalline diamond compacts (PDC) have been widely used as cutting elements in the drilling tools for the oil, gas, civil and mining industries because of their faster penetration rates and longer bit life. US Department of Energy reports that PDC bits account for more than one-third of the total footage drilled worldwide (US Department of Energy, 2004). However, non-thermally-stable diamond composites (NTSDC) have seldom been applied to geothermal drilling, since premature failures of such PDC cutters have been observed in hard rock formations. Several factors need to be considered to prevent premature failure of cutters and improve cutting performance when using PDC-based bits and other rock cutting tools. The first set of factors consists of the strength, density, stiffness, toughness and thermal resistance of the PDC and the rock. A second set relates to the complex behaviour of the bonding between the PDC cutter and the bit matrix, or the pick and the pick holder, which is vital in maintaining stable, reliable and durable adhesion of the cutters to their hubs. Finally, based on a better understanding of the cutting processes, the formulation of a predictive model would assist in further development of cutter design.

Jan 1, 2004

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970