Search Documents

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By Robert T. Langland

The Bureau of Mines, at its Denver, Colo., research center, has developed a computer program to solve nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship assumed, the unknown parameters may be evaluated by the Newton-Raphson method of iteration. Variances and covariances of the parameters are derived, based on the propagation of errors. A creep function is established from shale test data as an example of program utility. Program accuracy is compared to the accuracies of other programs in present day use.

Jan 1, 1974

By Mantsevich M, Ivanov V, Volkov V, Ponomarov G

A new ecologically promising technology for the copper-nickel ore benefication using insert gases and pyrrhotite depression is under consideration. The finely dispersed nickel-containing sulphides and the pyrrhotite are easily oxidised during the process of flotation resulting in deterioration of selectivity and valuable component loss in the tailings. One of the ways to improve the benefication is the flotation of easily-oxidising minerals in an inert atmosphere. In the experiments nitrogen was taken as the inert gas supposing that in the industrial scale operations nitrogen generating, as a by-product of the oxigen production. will be used (Rybas et at, 1989). The most wide-spread mineral in the Norilsk rich sulphide copper-nickel ores is pyrrhotite containing iron, sulphur, nickel and platinum group metals. Up to 30 per cent of the pyrrhotite sulphur is recovered into the nickel concentrate causing the high sulphur dioxide emission in the further pyrometallurgical process of nickel production. This is the reason why the problem of the pyrrhotite removal during the ore concentration should be solved, the critical factor of the problem being the lowest possible nickel content in the pyrrhotite. According to the data of the geological and mineralogical mapping the nickel content in the pyrrhotites of rich ores varies from 0.3 to 1.8 per cent, with the mean value equal to 0.6 - 0.8 per cent. This assures the technological and economical effectiveness of the low-grade pyrrhotite removal during the flotation process.

Jan 1, 1993

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"INTRODUCTION The design, development, fabrication, and test of cryogenic breathing apparatus is part of a much larger effort funded by the National Institute for Occupational Safety and Health (NIOSH) and managed through a Space Act Agreement with the National Aeronautics and Space Administration (NASA) at the Kennedy Space Center (KSC) in Florida. This effort is designed to create cryogenically based life support equipment that is responsive to the needs of miners as required by the Miner Act of 2006. Our goal was to design and build a liquid air based self-contained breathing apparatus (SCBA) that lasted 2 hours and would be used for the egress of miners during a mining accident and be refillable while worn. Therefore, the current report describes tests of an Advanced Cryogenic Breathing Apparatus (termed the ACryoBA) designed to provide miners egressing an emergency situation with a two-hour open-circuit SCBA. The ACryoBA utilizes low pressure cryogenic liquid air instead of high pressure compressed air commonly used in most commercially available SCBA. The ACryoBA can also be self-filled from strategically placed Cryogenic Air Supply and Fill Stations (CryoASFS) initially, and thereafter on the egress route approximately every 1 hour and 30 minutes with a 30 minute air reserve. The ACryoBA evolved originally from a one hour Liquid Air Pack (LAP) developed in the 1980’s for Space Shuttle Rescue forces allowing for longer duration and cool air (Figure 1). It was used successfully for many years, through the end of the Space Shuttle Program. The first attempt at a mine egress pack was the Cryogenic Breathing Apparatus (Figure 2). It was to have a low profile, two hours of breathing, attitude independence, and a simple rapid refill while in use. The CryoBA met the two hour criteria, but with difficulty due to excessive heat leakage caused by the dual 4 liter Dewar design. Much of the stored air was lost as it vaporized faster than it could be used. However, the pack was successful in demonstrating both attitude independence and a simple rapid refill capability. The ACryoBA project was designed to continue the progression and address the deficiencies in the CryoBA. The ACryoBA pack was designed to last 2 hours. It minimizes the heat leakage with a single Dewar and thereby requires less liquid air. The single Dewar design also minimizes weight, making it much more manageable by the user (Figure 3). The ACryoBA complies with 42 CFR part 84 NIOSH certification test requirements. One critical requirement for the ACryoBA is operation in positions other than vertical for periods up to 1/4 (i.e. 30 minutes) of the rated service life of 2 hours; this was accomplished by use of new technology called the “attitude independent pickup” which is abbreviated “AIP.” The AIP, developed by BCS Life Support LLC (patent #8,899,226), has a tube going from the top flange down through the center of the Dewar. At the end it has a flexible bellows and a weighted end. Due to the flexible nature of the bellows, the pickup at the end is free to rotate and follow the liquid level around within +/- 90o of vertical."

Jan 1, 2016

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By Olav Moklebust

The R-N Process is an outgrowth of the development by the National Lead Company&apos;s Norwegian subsidiary Titania A/S, of a process for producing metallic iron and a high titanium content co-product from ilmenite. Development of the process for the treatment of iron ores was continued as a joint project of the Republic Steel Corporation and the National Lead Company in 1953. More recently in July, 1957, the R-N Corporation was created by these two companies to undertake the commercial promotion of the results of this joint project. This paper has been prepared with the permission and encouragement of these three companies. The R-N process has as its objective the making of metallic iron from iron ores or iron ore concentrates. The general principles of the process have already been disclosed in technical papers and patents. In general the process comprises the following steps: 1. Iron oxide in crushed natural iron ores or iron ore concentrates is reduced to about 95% metallic iron, without fusion in a rotary kiln in the presence of solid carbonaceous fuel,*such as, coke or char, limestone and combustible gases. 2. The kiln discharge, consisting of metallized ore, coke, lime and coke ashes, is cooled. The excess coke is regenerated and recycled to the kiln feed.

Jan 1, 1959

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By Brian Lindner, Lidia Auret, Niel Knoblauch

In this paper, a fault detection and identification framework based on feature extraction and topology extraction methods is proposed, and evaluated on a simulated base metals refinery high pressure leaching process. Feature extraction methods included linear and kernel principal component analysis, while process topology information was extracted with linear cross-correlation, partial cross-correlation and transfer entropy. Connectivity maps were constructed to identify possible fault propagation paths to aid root cause analysis. The results indicate that process topology can enhance the fault identification capability of data-based process monitoring methods. The study of the considered base metals refinery pressure leaching process is ongoing, with future work including the creation of a fault library which would lead to further critical evaluation of the proposed fault detection and identification framework.

Jan 1, 2014

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By W. A. Griffith

Fractional replication of factorial design, a general method for planning experimentation and for analysis of data obtained, is described as applied to a flotation investigation. This method leads to determination of optimum process conditions with minimum experimental effort. Its advantages over simple factorial design are demonstrated. A METHOD for planning experimentation and for analyzing the data secured will be demonstrated. This method, termed fractional replication of factorial design, employs a relatively small number of individual experiments to determine which of a large number of process variables are controlling, to determine which combination of levels of these variables is most likely to produce optimum results, and also to predict what results will be obtained with a particular combination of conditions not already tested. Although the general method is not new, having been developed by Finney in 1945,&apos; the extent to which it can improve the effectiveness of applied research generally has not been recognized by metallurgists. The fractional replication procedure is particularly useful in flotation experimentation and an example from such an investigation will be used in the paper. However, it has equal value in any investigation in which similar experimental difficulties are encountered. In developing a flotation process for a particular mineral separation, the investigator is inevitably confronted with the following difficulties: 1—There are a large number of potentially important process variables. 2—Results of individual experiments are not highly reproducible, due in part to the difficulty in precisely controlling all the variables. 3—Considerable effort is expended in conducting individual experiments. 4—There are practical limits on the number of individual experiments which can be made. In situations of just such a type, modern statistical methods of planning experimentation and analyzing data have their greatest value. Applications of one such technique, called factorial design, to problems of this type have been described by Dorenfeld and others.&apos;-&apos; The simple factorial design is an efficient procedure when the investigator hopes to provide a comprehensive understanding of the effects and interrelationships of a small number of variables over a limited range. In applied research, this is seldom the main objective. Rather, the investigator usually wishes to determine which of the many potentially important variables are in fact controlling, which levels of the controlling variables will provide opti- mum metallurgical results, and what these results will be at optimum conditions. Interest in detailed trends is limited to the controlling variables and to levels in the region of optimum conditions. Simple factorial design has serious deficiencies for such objectives and is not the most efficient method of experimental design. Deficiencies of Factorial Design In a simple factorial design, an experiment must be made at every possible combination of each level of every variable, once these have been chosen and the levels of each to be included have been decided upon. As the number of variables or levels of each increases, the experimental program quickly reaches prohibitive size. For example, an investigation of only four variables, each at four levels, requires 256 individual experiments. Often upon completion of such an extensive program, it is found that one or more of the variables has metallurgically unimportant effects or that a poor estimate has been made as to the appropriate range of levels to be investigated. The result is that only a small proportion of the data obtained falls in the range of real metallurgical interest. Indeed, it frequently can be anticipated that certain combinations of levels of variables will not produce results of interest, but they still must be included so that the essential balance, or orthogonality, of the design will be retained. It may be true that factorial design will provide the greatest amount of information from a given number of experiments, but it does not necessarily follow that it will lead to the desired information with a minimum number of experiments. Much of the information provided may be of little value. Advantages of Fractional Replication The disadvantages of simple factorial design are overcome to a great extent by a modification known as fractional replication. This is a technique for sampling systematically the potential data of a full factorial experiment, that is, the data which would have been obtained if the complete factorially designed program had been completed. Only a fraction of the total array of experiments is made, but the experiments are chosen in such a way that the important advantages of factorial design and the accompanying analysis of variance are retained. The data obtained from the first group of experiments are used to determine which of several variables are controlling and which levels of these variables are most likely to produce the desired result. Unimportant variables and levels of variables then may be

Jan 1, 1956

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024